Provided by: gdbmtool_1.14.1-6_amd64 
NAME
gdbmtool - examine and modify a GDBM database
SYNOPSIS
gdbmtool [-lmNnqrs] [-b SIZE] [-c SIZE] [-f FILE] [--block-size=SIZE]
[--cache-size=SIZE] [--file FILE] [--newdb] [--no-lock]
[--no-mmap] [--norc]
[--quiet] [--read-only] [--synchronize] [DBFILE]
gdbmtool [-Vh] ][--help] [--usage] [--version]
DESCRIPTION
The gdbmtool utility allows you to view and modify an existing GDBM database or to create
a new one.
The DBFILE argument supplies the name of the database to open. If not supplied, the
default name junk.gdbm is used instead. If the named database does not exist, it will be
created. An existing database can be cleared (i.e. all records removed from it) using the
--newdb option (see below).
Unless the -N (--norc) option is given, after startup gdbmtool looks for file named
.gdbmtoolrc first in the current working directory, and, if not found there, in the home
directory of the user who started the program. If found, this file is read and
interpreted as a list of gdbmtool commands.
Then gdbmtool starts a loop, in which it reads commands from the standard input, executes
them and prints the results on the standard output. If the standard input is attached to
a console, the program runs in interactive mode.
The program terminates when the quit command is given, or end-of-file is detected on its
standard input.
A gdbmtool command consists of a command verb, optionally followed by one or more
arguments, separated by any amount of white space. A command verb can be entered either
in full or in an abbreviated form, as long as that abbreviation does not match any other
verb.
Any sequence of non-whitespace characters appearing after the command verb forms an
argument. If the argument contains whitespace or unprintable characters it must be
enclosed in double quotes. Within double quotes the usual escape sequences are
understood, as shown in the table below:
Escape Expansion
\a Audible bell character (ASCII 7)
\b Backspace character (ASCII 8)
\f Form-feed character (ASCII 12)
\n Newline character (ASCII 10)
\r Carriage return character (ASCII 13)
\t Horizontal tabulation character (ASCII 9)
\v Vertical tabulation character (ASCII 11)
\\ Single slash
In addition, a backslash immediately followed by the end-of-line character effectively
removes that character, allowing to split long arguments over several input lines.
OPTIONS
-b, --block-size=SIZE
Set block size.
-c, --cache-size=SIZE
Set cache size.
-f, --file=FILE
Read commands from FILE, instead of from the standard input.
-l, --no-lock
Disable file locking.
-m, --no-mmap
Do not use mmap(2).
-n, --newdb
Create the database, truncating it if it already exists.
-q, --quiet
Don't print initial banner.
-r, --read-only
Open database in read-only mode.
-s, --synchronize
Synchronize to disk after each write.
-h, --help
Print a short usage summary.
--usage
Print a list of available options.
-V, --version
Print program version
SHELL COMMANDS
avail Print the avail list.
bucket NUM
Print the bucket number NUM and set is as the current one.
cache Print the bucket cache.
close Close the currently open database.
count Print the number of entries in the database.
current
Print the current bucket.
delete KEY
Delete record with the given KEY.
dir Print hash directory.
export FILE-NAME [truncate] [binary|ascii]
Export the database to the flat file FILE-NAME. This is equivalent to
gdbm_dump(1).
This command will not overwrite an existing file, unless the truncate parameter is
also given. Another optional parameter determines the type of the dump (*note Flat
files::). By default, ASCII dump will be created.
fetch KEY
Fetch and display the record with the given KEY.
first Fetch and display the first record in the database. Subsequent records can be
fetched using the next command (see below).
hash KEY
Compute and display the hash value for the given KEY.
header Print file header.
help or ?
Print a concise command summary, showing each command letter and verb with its
parameters and a short description of what it does. Optional arguments are
enclosed in square brackets.
history
Shows the command history list with line numbers. This command is available only
if the program was compiled with GNU Readline.
history COUNT.
Shows COUNT latest commands from the command history.
history N COUNT.
Shows COUNT commands from the command history starting with Nth command.
import FILE-NAME [replace] [nometa]
Import data from a flat dump file FILE-NAME. If the replace argument is given, any
records with the same keys as the already existing ones will replace them. The
nometa argument turns off restoring meta-information from the dump file.
list List the contents of the database.
next [KEY]
Sequential access: fetch and display the next record. If the KEY is given, the
record following the one with this key will be fetched.
open FILE
Open the database file FILE. If successful, any previously open database is
closed. Otherwise, if the operation fails, the currently opened database remains
unchanged.
This command takes additional information from the variables open, lock, mmap, and
sync. See the section VARIABLES, for a detailed description of these.
quit Close the database and quit the utility.
reorganize
Reorganize the database.
set [VAR=VALUE...]
Without arguments, lists variables and their values. If arguments are specified,
sets variables. Boolean variables can be set by specifying variable name,
optionally prefixed with no, to set it to false.
source FILE
Read commands from the given FILE.
status Print current program status.
store KEY DATA
Store the DATA with the given KEY in the database. If the KEY already exists, its
data will be replaced.
unset VARIABLE...
Unsets listed variables.
version
Print the version of gdbm.
DATA DEFINITIONS
The define statement provides a mechanism for defining key or content structures. It is
similar to the C struct declaration:
define key|content { defnlist }
The defnlist is a comma-separated list of member declarations. Within defnlist the
newline character looses its special meaning as the command terminator, so each
declaration can appear on a separate line and arbitrary number of comments can be inserted
to document the definition.
Each declaration has one of the following formats
type name
type name [N]
where type is a data type and name is the member name. The second format defines the
member name as an array of N elements of type.
The supported types are:
type meaning
char single byte (signed)
short signed short integer
ushort unsigned short integer
int signed integer
unsigned unsigned integer
uint ditto
long signed long integer
ulong unsigned long integer
llong signed long long integer
ullong unsigned long long integer
float a floating point number
double double-precision floating point number
string array of characters (see the NOTE below)
stringz null-terminated string of characters
The following alignment declarations can be used within defnlist:
offset N
The next member begins at offset N.
pad N Add N bytes of padding to the previous member.
For example:
define content {
int status,
pad 8,
char id[3],
stringz name
}
To define data consisting of a single data member, the following simplified construct can
be used:
define key|content type
where type is one of the types discussed above.
NOTE: The string type can reasonably be used only if it is the last or the only member of
the data structure. That's because it provides no information about the number of
elements in the array, so it is interpreted to contain all bytes up to the end of the
datum.
VARIABLES
confirm, boolean
Whether to ask for confirmation before certain destructive operations, such as
truncating the existing database. Default is true.
ps1, string
Primary prompt string. Its value can contain conversion specifiers, consisting of
the % character followed by another character. These specifiers are expanded in
the resulting prompt as follows:
Sequence Expansion
%f name of the db file
%p program name
%P package name (gdbm)
%_ horizontal space (ASCII 32)
%v program version
%% %
The default prompt is %p>%_.
ps2, string
Secondary prompt. See ps1 for a description of its value. This prompt is
displayed before reading the second and subsequent lines of a multi-line command.
The default value is %_>%_.
delim1, string
A string used to delimit fields of a structured datum on output (see the section
DATA DEFINITIONS).
Default is , (a comma). This variable cannot be unset.
delim2, string
A string used to delimit array items when printing a structured datum.
Default is , (a comma). This variable cannot be unset.
pager, string
The name and command line of the pager program to pipe output to. This program is
used in interactive mode when the estimated number of output lines is greater then
the number of lines on your screen.
The default value is inherited from the environment variable PAGER. Unsetting this
variable disables paging.
quiet, boolean
Whether to display welcome banner at startup. This variable should be set in a
startup script file.
The following variables control how the database is opened:
cachesize, numeric
Sets the cache size. By default this variable is not set.
blocksize, numeric
Sets the block size. Unset by default.
open, string
Open mode. The following values are allowed:
newdb Truncate the database if it exists or create a new one. Open it in read-
write mode.
wrcreat or rw
Open the database in read-write mode. Create it if it does not exist. This
is the default.
reader or readonly
Open the database in read-only mode. Signal an error if it does not exist.
lock, boolean
Lock the database. This is the default.
mmap, boolean
Use memory mapping. This is the default.
SEE ALSO
gdbm_dump(1), gdbm_load(1), gdbm(3).
REPORTING BUGS
Report bugs to <bug-gdbm@gnu.org>.
COPYRIGHT
Copyright © 2013 Free Software Foundation, Inc
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it. There is NO WARRANTY,
to the extent permitted by law.