Provided by: shorewall_5.1.12.2-1_all bug

NAME

       policy - Shorewall policy file

SYNOPSIS

       /etc/shorewall[6]/policy

DESCRIPTION

       This file defines the high-level policy for connections between zones defined in
       shorewall-zones[1](5).

           Important
           The order of entries in this file is important

           This file determines what to do with a new connection request if we don't get a match
           from the shorewall-blrules[2](5) or shorewall-rules[3](5) files. For each
           source/destination pair, the file is processed in order until a match is found ("all"
           will match any source or destination).

           Important
           Intra-zone policies are pre-defined

           For $FW and for all of the zones defined in shorewall-zones[1](5), the POLICY for
           connections from the zone to itself is ACCEPT (with no logging or TCP connection rate
           limiting) but may be overridden by an entry in this file. The overriding entry must be
           explicit (specifying the zone name in both SOURCE and DEST) or it must use "all+"
           (Shorewall 4.5.17 or later).

           Similarly, if you have IMPLICIT_CONTINUE=Yes in shorewall.conf[4](5), then the
           implicit policy to/from any sub-zone is CONTINUE. These implicit CONTINUE policies may
           also be overridden by an explicit entry in this file.

       The columns in the file are as follows (where the column name is followed by a different
       name in parentheses, the different name is used in the alternate specification syntax).

       SOURCE - zone[,...[+]]|$FW|all|all+
           Source zone. Must be the name of a zone defined in shorewall-zones[1](5), $FW, "all"
           or "all+".

           Support for "all+" was added in Shorewall 4.5.17. "all" does not override the implicit
           intra-zone ACCEPT policy while "all+" does.

           Beginning with Shorewall 5.0.12, multiple zones may be listed separated by commas. As
           above, if '+' is specified after two or more zone names, then the policy overrides the
           implicit intra-zone ACCEPT policy if the same zone appears in both the SOURCE and DEST
           columns.

       DEST - zone[,...[+]]|$FW|all|all+
           Destination zone. Must be the name of a zone defined in shorewall-zones[1](5), $FW,
           "all" or "all+". If the DEST is a bport zone, then the SOURCE must be "all", "all+",
           another bport zone associated with the same bridge, or it must be an ipv4 zone that is
           associated with only the same bridge.

           Support for "all+" was added in Shorewall 4.5.17. "all" does not override the implicit
           intra-zone ACCEPT policy while "all+" does.

           Beginning with Shorewall 5.0.12, multiple zones may be listed separated by commas. As
           above, if '+' is specified after two or more zone names, then the policy overrides the
           implicit intra-zone ACCEPT policy if the same zone appears in both the SOURCE and DEST
           columns.

       POLICY -
       {ACCEPT|DROP|REJECT|BLACKLIST|CONTINUE|QUEUE|NFQUEUE[(queuenumber1[:queuenumber2])]|NONE}[:{[+]policy-action[:level][,...]|None}]
           Policy if no match from the rules file is found.

           If the policy is neither CONTINUE nor NONE then the policy may be followed by ":" and
           one of the following:

            1. The word "None" or "none". This causes any default action defined in
               shorewall.conf[4](5) to be omitted for this policy.

            2. The name of an action with optional parameters enclosed in parentheses. The action
               will be invoked before the policy is enforced.

           Actions can have parameters specified.

           Beginning with Shorewall 4.5.10, the action name can be followed optionally by a colon
           and a log level. The level will be applied to each rule in the action or body that
           does not already have a log level.

           Beginning with Shorewall 5.1.2, multiple action[:level] specification may be listeded,
           separated by commas. The actions are invoked in the order listed. Also beginning with
           Shorewall 5.1.2, the policy-action list can be prefixed with a plus sign ("+")
           indicating that the listed actions are in addition to those listed in the related
           _DEFAULT setting in shorewall.conf[4](5).

           Possible policies are:

           ACCEPT
               Accept the connection.

           DROP
               Ignore the connection request.

           REJECT
               For TCP, send RST. For all other, send an "unreachable" ICMP.

           BLACKLIST
               Added in Shorewall 5.1.1 and requires that the DYNAMIC_BLACKLIST setting in
               shorewall.conf[4](5) specifies ipset-based dynamic blacklisting. The SOURCE IP
               address is added to the blacklist ipset and the connection request is ignored.

           QUEUE
               Queue the request for a user-space application such as Snort-inline.

           NFQUEUE
               Queue the request for a user-space application using the nfnetlink_queue
               mechanism. If a queuenumber1 is not given, queue zero (0) is assumed. Beginning
               with Shorewall 4.6.10, a second queue number (queuenumber2) may be given. This
               specifies a range of queues to use. Packets are then balanced across the given
               queues. This is useful for multicore systems: start multiple instances of the
               userspace program on queues x, x+1, .. x+n and use "x:x+n". Packets belonging to
               the same connection are put into the same nfqueue.

           CONTINUE
               Pass the connection request past any other rules that it might also match (where
               the source or destination zone in those rules is a superset of the SOURCE or DEST
               in this policy). See shorewall-nesting[5](5) for additional information.

           NONE
               Assume that there will never be any packets from this SOURCE to this DEST.
               Shorewall will not create any infrastructure to handle such packets and you may
               not have any rules with this SOURCE and DEST in the /etc/shorewall/rules file. If
               such a packet is received, the result is undefined. NONE may not be used if the
               SOURCE or DEST columns contain the firewall zone ($FW) or "all".

       LOGLEVEL (loglevel) - [log-level|ULOG|NFLOG]
           Optional - if supplied, each connection handled under the default POLICY is logged at
           that level. If not supplied, no log message is generated. See syslog.conf(5) for a
           description of log levels.

           You may also specify ULOG or NFLOG (must be in upper case). This will log to the ULOG
           or NFLOG target and will send to a separate log through use of ulogd
           (http://www.netfilter.org/projects/ulogd/index.html).

           For a description of logging, see shorewall-logging(5)[6].

           If you don't want to log but need to specify the following column, place "-" here.

       RATE (rate) - [-|limit]
           where limit is one of:
               [-|[{s|d}:[[name]:]]]rate/{sec|min|hour|day}[:burst]
               [name1]:rate1/{sec|min|hour|day}[:burst1],[name2]:rate2/{sec|min|hour|day}[:burst2]
           If passed, specifies the maximum TCP connection rate and the size of an acceptable
           burst. If not specified, TCP connections are not limited. If the burst parameter is
           omitted, a value of 5 is assumed.

           When s: or d: is specified, the rate applies per source IP address or per destination
           IP address respectively. The name may be chosen by the user and specifies a hash table
           to be used to count matching connections. If not give, the name shorewall is assumed.
           Where more than one POLICY or rule specifies the same name, the connections counts for
           the policies are aggregated and the individual rates apply to the aggregated count.

           Beginning with Shorewall 4.6.5, two limits may be specified, separated by a comma. In
           this case, the first limit (name1, rate1, burst1) specifies the per-source IP limit
           and the second limit specifies the per-destination IP limit.

           Example: client:10/sec:20,:60/sec:100

       CONNLIMIT - limit[:mask]
           May be used to limit the number of simultaneous connections from each individual host
           to limit connections. While the limit is only checked on connections to which this
           policy could apply, the number of current connections is calculated over all current
           connections from the SOURCE host. By default, the limit is applied to each host
           individually but can be made to apply to networks of hosts by specifying a mask. The
           mask specifies the width of a VLSM mask to be applied to the source address; the
           number of current connections is then taken over all hosts in the subnet
           source-address/mask.

EXAMPLE

        1. All connections from the local network to the internet are allowed

        2. All connections from the internet are ignored but logged at syslog level KERNEL.INFO.

        3. All other connection requests are rejected and logged at level KERNEL.INFO.

                   #SOURCE         DEST            POLICY          LOG           BURST:LIMIT
                   #                                               LEVEL
                   loc             net             ACCEPT
                   net             all             DROP            info
                   #
                   # THE FOLLOWING POLICY MUST BE LAST
                   #
                   all             all             REJECT          info

FILES

       /etc/shorewall/policy

       /etc/shorewall6/policy

SEE ALSO

       http://www.shorewall.net/configuration_file_basics.htm#Pairs[7]

       shorewall(8)

NOTES

        1. shorewall-zones
           http://www.shorewall.net/manpages/shorewall-zones.html

        2. shorewall-blrules
           http://www.shorewall.net/manpages/shorewall-blrules.html

        3. shorewall-rules
           http://www.shorewall.net/manpages/shorewall-rules.html

        4. shorewall.conf
           http://www.shorewall.net/manpages/shorewall.conf.html

        5. shorewall-nesting
           http://www.shorewall.net/manpages/shorewall-nesting.html

        6. shorewall-logging(5)
           http://www.shorewall.net/shorewall_logging.html

        7. http://www.shorewall.net/configuration_file_basics.htm#Pairs
           http://www.shorewall.net/configuration_file_basics.htm#Pairs