Provided by: smp-utils_0.98-1_amd64 bug

NAME

       smp_rep_phy_err_log - invoke REPORT PHY ERROR LOG SMP function

SYNOPSIS

       smp_rep_phy_err_log    [--help]    [--hex]    [--interface=PARAMS]    [--phy=ID]   [--raw]
       [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]

DESCRIPTION

       Sends a SAS Serial Management Protocol (SMP) REPORT PHY ERROR LOG function request  to  an
       SMP  target. The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on
       the interface, the SAS_ADDR may be deduced from the SMP_DEVICE.  The  mpt  interface  uses
       SMP_DEVICE  to  identify  a  HBA  (an  SMP  initiator)  and  needs  the  additional  ,N to
       differentiate between HBAs if there are multiple present.

OPTIONS

       Mandatory arguments to long options are mandatory for short options as well.

       -h, --help
              output the usage message then exit.

       -H, --hex
              output the response (less the CRC field) in hexadecimal.

       -I, --interface=PARAMS
              interface specific parameters. In this case "interface" refers to the path  through
              the  operating  system  to  the  SMP initiator. See the smp_utils man page for more
              information.

       -p, --phy=ID
              phy identifier. ID is a value between 0 and 254. Default is 0.

       -r, --raw
              send the response (less the CRC field) to stdout in binary. All error messages  are
              sent to stderr.

       -s, --sa=SAS_ADDR
              specifies  the SAS address of the SMP target device. Typically this is an expander.
              This option may not be needed if the SMP_DEVICE has the target's SAS address within
              it.  The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To
              give a number in hexadecimal either prefix it with '0x' or put a  trailing  'h'  on
              it.

       -v, --verbose
              increase the verbosity of the output. Can be used multiple times

       -V, --version
              print the version string and then exit.

       -z, --zero
              zero the Allocated Response Length field in the request. This option also zeros the
              Request  Length  field  in  the  request.  This  is  required  for  strict  SAS-1.1
              compliance.  However  this  option should not be given in SAS-2 and later; if it is
              given an abridged response may result.

NOTES

       Similar information is maintained for SAS SSP target phys (e.g. on a SAS disk). It can  be
       obtained from the Protocol Specific Port log page with the sg_logs utility.

       Similar  information  may  be  obtained  for SAS initiator phys (e.g. on a SAS HBA). As an
       example  in  Linux  2.6.28  error   information   can   be   found   in   this   directory
       /sys/class/sas_phy/phy-4:0 (for the phy 0 in SCSI/SAS host 4).

       Similar  information  may be obtained for SATA device phys (e.g. on a SATA disk). If there
       is a SAT layer between OS and the SATA device then the sg_sat_phy_event utility can  fetch
       the information.

CONFORMING TO

       The  SMP  REPORT  PHY  ERROR  LOG function was introduced in SAS-1 .  The "Expander change
       count" field was added in SAS-2 .

AUTHORS

       Written by Douglas Gilbert.

REPORTING BUGS

       Report bugs to <dgilbert at interlog dot com>.

COPYRIGHT

       Copyright © 2006-2011 Douglas Gilbert
       This software is distributed under a FreeBSD license. There is NO warranty; not  even  for
       MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

SEE ALSO

       smp_utils, smp_phy_control(smp_utils), sg_logs(sg3_utils), sg_sat_phy_event(sg3_utils)