NAME

       Config::Model::models::LCDd::picolcd - Configuration class LCDd::picolcd

DESCRIPTION

       Configuration classes used by Config::Model

       generated from LCDd.conf

Elements

   Backlight
       Sets the initial state of the backlight upon start-up.  Optional. Type boolean.

       upstream_default value :
           on

   Brightness
       Set the initial brightness . Works only with the 20x4 device.  Optional. Type integer.

       upstream_default value :
           1000

   Contrast
       Set the initial contrast  Optional. Type integer.

       upstream_default value :
           1000

   Key0Light
       If Keylights is on, the you can unlight specific keys below: Key0 is the directional pad.
       Key1 - Key5 correspond to the F1 - F5 keys.  There is no LED for the +/- keys.  This is a
       handy way to indicate to users which keys are disabled.   Optional. Type boolean.

       upstream_default value :
           on

   Key1Light
        Optional. Type uniline.

       default value :
           on

   Key2Light
        Optional. Type uniline.

       default value :
           on

   Key3Light
        Optional. Type uniline.

       default value :
           on

   Key4Light
        Optional. Type uniline.

       default value :
           on

   Key5Light
        Optional. Type uniline.

       default value :
           on

   KeyRepeatDelay
       Key auto repeat is only available if the picoLCD driver is built with libusb-1.0. Use
       KeyRepeatDelay and KeyRepeatInterval to configure key auto repeat.

       Key auto repeat delay (time in ms from first key report to first repeat). Use zero to
       disable auto repeat.  Optional. Type integer.

       upstream_default value :
           300

   KeyRepeatInterval
       Key auto repeat interval (time in ms between repeat reports). Only used if KeyRepeatDelay
       is not zero.  Optional. Type integer.

       upstream_default value :
           200

   KeyTimeout
       KeyTimeout is only used if the picoLCD driver is built with libusb-0.1. When built with
       libusb-1.0 key and IR data is input asynchronously so there is no need to wait for the USB
       data.  KeyTimeout is the time in ms that LCDd spends waiting for a key press before
       cycling through other duties.  Higher values make LCDd use less CPU time and make key
       presses more detectable.  Lower values make LCDd more responsive but a little prone to
       missing key presses.  500 (.5 second) is the default and a balanced value.  Optional. Type
       integer.

       upstream_default value :
           500

   Keylights
       Light the keys?  Optional. Type boolean.

       upstream_default value :
           on

   LinkLights
       Link the key lights to the backlight?  Optional. Type boolean.

       upstream_default value :
           on

   LircFlushThreshold
       Threshold in microseconds of the gap that triggers flushing the IR data to lirc If
       LircTime_us is on values greater than 32.767ms will disable the flush If LircTime_us is
       off values greater than 1.999938s will disable the flush.  Optional. Type integer.

       upstream_default value :
           8000

   LircHost
       Host name or IP address of the LIRC instance that is to receive IR codes If not set, or
       set to an empty value, IR support is disabled.  Optional. Type uniline.

       upstream_default value :
           127.0.0.1

   LircPort
       UDP port on which LIRC is listening  Optional. Type integer.

       upstream_default value :
           8765

   LircTime_us
       UDP data time unit for LIRC On:  times sent in microseconds (requires LIRC UDP driver that
       accepts this).  Off: times sent in 'jiffies' (1/16384s) (supported by standard LIRC UDP
       driver).  Optional. Type boolean.

       upstream_default value :
           off

   OffBrightness
       Set the brightness while the backlight is 'off' .  Works only with the 20x4 device.
       Optional. Type integer.

       upstream_default value :
           0

SEE ALSO

       •   cme