Provided by: shorewall_5.1.12.2-1_all bug

NAME

       arprules - Shorewall ARP rules file

SYNOPSIS

       /etc/shorewall/arprules

DESCRIPTION

       IPv4 only.

       This file was added in Shorewall 4.5.12 and is used to describe low-level rules managed by
       arptables (8). These rules only affect Address Resolution Protocol (ARP), Reverse Address
       Resolution Protocol (RARP) and Dynamic Reverse Address Resolution Protocol (DRARP) frames.

       The columns in the file are as shown below. MAC addresses are specified normally (6
       hexadecimal numbers separated by colons).

       ACTION
           Describes the action to take when a frame matches the criteria in the other columns.
           Possible values are:

           ACCEPT
               This is the default action if no rules matches a frame; it lets the frame go
               through.

           DROP
               Causes the frame to be dropped.

           SNAT:ip-address
               Modifies the source IP address to the specified ip-address.

           DNAT:ip-address
               Modifies the destination IP address to the specified ip-address.

           SMAT:mac-address
               Modifies the source MAC address to the specified mac-address.

           DMAT:mac-address
               Modifies the destination MAC address to the specified mac-address.

           SNATC:ip-address
               Like SNAT except that the frame is then passed to the next rule.

           DNATC:ip-address
               Like DNAT except that the frame is then passed to the next rule.

           SMATC:mac-address
               Like SMAT except that the frame is then passed to the next rule.

           DMATC:mac-address
               Like DMAT except that the frame is then passed to the next rule.

       SOURCE - [interface[:[!]ipaddress[/ipmask][:[!]macaddress[/macmask]]]]
           Where

           interface
               Is an interface defined in shorewall-interfaces(5).

           ipaddress
               is an IPv4 address. DNS names are not allowed.

           ipmask
               specifies a mask to be applied to ipaddress.

           macaddress
               The source MAC address.

           macmask
               Mask for MAC address; must be specified as 6 hexadecimal numbers separated by
               colons.

           When '!' is specified, the test is inverted.

           If not specified, matches only frames originating on the firewall itself.

               Caution
               Either SOURCE or DEST must be specified.

       DEST - [interface[:[!]ipaddress[/ipmask][:[!]macaddress[/macmask]]]]
           Where

           interface
               Is an interface defined in shorewall-interfaces(5).

           ipaddress
               is an IPv4 address. DNS Names are not allowed.

           ipmask
               specifies a mask to be applied to frame addresses.

           macaddress
               The destination MAC address.

           macmask
               Mask for MAC address; must be specified as 6 hexadecimal numbers separated by
               colons.

           When '!' is specified, the test is inverted and the rule matches frames which do not
           match the specified address/mask.

           If not specified, matches only frames originating on the firewall itself.

           If both SOURCE and DEST are specified, then both interfaces must be bridge ports on
           the same bridge.

               Caution
               Either SOURCE or DEST must be specified.

       OPCODE - [[!]opcode]
           Optional. Describes the type of frame. Possible opcode values are:

           1
               ARP Request

           2
               ARP Reply

           3
               RARP Request

           4
               RARP Reply

           5
               Dynamic RARP Request

           6
               Dynamic RARP Reply

           7
               Dynamic RARP Error

           8
               InARP Request

           9
               ARP NAK

           When '!' is specified, the test is inverted and the rule matches frames which do not
           match the specified opcode.

EXAMPLE

       The eth1 interface has both a public IP address and a private address (10.1.10.11/24).
       When sending ARP requests to 10.1.10.0/24, use the private address as the IP source:

           #ACTION                SOURCE                  DEST                ARP OPCODE
           SNAT:10.1.10.11        -                       eth1:10.1.10.0/24   1

FILES

       /etc/shorewall/arprules

SEE ALSO

       shorewall(8)