Provided by: tnat64_0.05-1build1_amd64 bug

NAME

       tnat64  -  Library  for  intercepting  outgoing  network  connections and redirecting them
       through the NAT64.

SYNOPSIS

       Set LD_PRELOAD to load the library then use applications as normal

       The syntax to force preload of the library for different shells is specified below:

       Bash, Ksh and Bourne shell -

       export LD_PRELOAD=/usr/lib/tnat64/libtnat64.so

       C Shell -

       setenv LD_PRELOAD=/usr/lib/tnat64/libtnat64.so

       This process can be automated (for Bash, Bourne and Korn shell users) for a single command
       or for all commands in a shell session by using the tnat64(1) script

       You  can  also  setup tnat64 in such a way that all processes automatically use it, a very
       useful configuration. For more information on this configuration see the  CAVEATS  section
       of this manual page.

DESCRIPTION

       tnat64  is  a  library  to  allow  IPv4-only application to access IPv4 hosts on IPv6-only
       systems by using NAT64. It wraps the normal  connect()  function.  When  a  connection  is
       attempted,  it  consults  the  configuration  file (which is defined at configure time but
       defaults to /etc/tnat64.conf) and determines if the IP address specified is local.  If  it
       is  not,  the  library redirects the connection to an IPv6 address inside the NAT64 prefix
       that is specified in the configuration file. The redirection  is  performed  only  if  the
       destination  host  is  unreachable  (when there's no route to host). Also, after the first
       successful redirection all the following connection attempts  are  redirected  immediately
       without  even  trying to connect to the host via IPv4. When the destination host cannot be
       reached via IPv6, the redirection is disabled.

       tnat64 avoids the need to recompile applications so they can use reach hosts even if  they
       do not support IPv6 and there's no IPv4 connectivity.

       tnat64  is  heavily based on the source code of tsocks, a library that intercepts outgoing
       TCP connections and redirects them though SOCKS proxy.  Many  thanks  for  tsocks  author,
       Shaun Clowes!

   ARGUMENTS
       Most  arguments to tnat64 are provided in the configuration file (the location of which is
       defined  at  configure  time  by  the  --with-conf=<file>   argument   but   defaults   to
       /etc/tnat64.conf). The structure of this file is documented in tnat64.conf(8)

       Some  configuration  options  can  be specified at run time using environment variables as
       follows:

       TNAT64_CONF_FILE
              This  environment  variable  overrides  the  default   location   of   the   tnat64
              configuration  file. This variable is not honored if the program tnat64 is embedded
              in is setuid. In addition this environment variable can be compiled out  of  tnat64
              with the --disable-envconf argument to configure at build time

       TNAT64_DEBUG
              This  environment  variable sets the level of debug output that should be generated
              by tnat64 (debug output is generated in the form of output to standard  error).  If
              this  variable  is  not  present  by  default  the  logging level is set to 0 which
              indicates that only error messages should be output.  Setting it to  higher  values
              will  cause tnat64 to generate more messages describing what it is doing. If set to
              -1 tnat64 will output absolutely no error  or  debugging  messages.  This  is  only
              needed if tnat64 output interferes with a program it is embedded in. Message output
              can be permanently compiled out of tnat64 by specifying the --disable-debug  option
              to configure at build time

       TNAT64_DEBUG_FILE
              This option can be used to redirect the tnat64 output (which would normally be sent
              to standard error) to a file. This variable is not honored if the program tnat64 is
              embedded  in  is  setuid.  For  programs where tnat64 output interferes with normal
              operation  this  option  is  generally  better  than   disabling   messages   (with
              TNAT64_DEBUG = -1)

   ERRORS
       tnat64  will generate error messages and print them to stderr when there are problems with
       the configuration file if the TNAT64_DEBUG environment variable is not set to  -1  or  and
       --disable-debug  was  not  specified  at compile time. This output may cause some problems
       with programs that redirect standard error.

   CAVEATS
       tnat64 will not in  the  above  configuration  be  able  to  provide  proxying  to  setuid
       applications or applications that are not run from a shell. You can force all applications
       to LD_PRELOAD the library by placing the path to libtnat64 in  /etc/ld.so.preload.  Please
       make sure you correctly enter the full path to the library in this file if you do this. If
       you get it wrong, you will be UNABLE TO DO ANYTHING with the machine and will have to boot
       it with a rescue disk and remove the file (or try the saveme program, see the INSTALL file
       for more info).  THIS IS A ***WARNING***, please be careful. Also be sure the  library  is
       in  the  root  filesystem  as  all  hell will break loose if the directory it is in is not
       available at boot time.

BUGS

       tnat64 can only proxy outgoing TCP connections

       tnat64 does NOT work correctly with asynchronous sockets (though it  does  work  with  non
       blocking  sockets).  This  bug  would  be very difficult to fix and there appears to be no
       demand for it (I know of no major application that uses asynchronous sockets)

       tnat64 uses ELF dynamic loader features to intercept dynamic function calls from  programs
       in  which  it  is embedded.  As a result, it cannot trace the actions of statically linked
       executables, non-ELF executables, or executables that make system calls directly with  the
       system call trap or through the syscall() routine.

FILES

       /etc/tnat64.conf - default tnat64 configuration file

SEE ALSO

       tnat64.conf(5) tnat64(1)

AUTHORS

       Andrew O. Shadura (bugzilla@tut.by), Shaun Clowes (delius@progsoc.uts.edu.au)

COPYRIGHT

       Copyright 2011 Andrew O. Shadura

       Original tsocks manual page, copyright 2000 Shaun Clowes

       tnat64  and  its  documentation  may  be  freely  copied under the terms and conditions of
       version 2 of the GNU General Public License, as published by the Free Software  Foundation
       (Cambridge, Massachusetts, United States of America).

       This  documentation  is  heavily  based  on  the  documentation  for  tsocks,  transparent
       SOCKSification library, whose documentation itself  is  based  on  the  documentation  for
       logwrites, another shared library interceptor. One line of code from it was used in tsocks
       and a lot of the documentation :) logwrites is by adam@yggdrasil.com (Adam J. Richter) and
       can be had from ftp.yggdrasil.com pub/dist/pkg