Provided by: postgresql-client-10_10.5-1_amd64 bug

NAME

       pg_recvlogical - control PostgreSQL logical decoding streams

SYNOPSIS

       pg_recvlogical [option...]

DESCRIPTION

       pg_recvlogical controls logical decoding replication slots and streams data from such
       replication slots.

       It creates a replication-mode connection, so it is subject to the same constraints as
       pg_receivewal(1), plus those for logical replication (see Chapter 48).

       pg_recvlogical has no equivalent to the logical decoding SQL interface's peek and get
       modes. It sends replay confirmations for data lazily as it receives it and on clean exit.
       To examine pending data on a slot without consuming it, use pg_logical_slot_peek_changes.

OPTIONS

       At least one of the following options must be specified to select an action:

       --create-slot
           Create a new logical replication slot with the name specified by --slot, using the
           output plugin specified by --plugin, for the database specified by --dbname.

       --drop-slot
           Drop the replication slot with the name specified by --slot, then exit.

       --start
           Begin streaming changes from the logical replication slot specified by --slot,
           continuing until terminated by a signal. If the server side change stream ends with a
           server shutdown or disconnect, retry in a loop unless --no-loop is specified.

           The stream format is determined by the output plugin specified when the slot was
           created.

           The connection must be to the same database used to create the slot.

       --create-slot and --start can be specified together.  --drop-slot cannot be combined with
       another action.

       The following command-line options control the location and format of the output and other
       replication behavior:

       -E lsn
       --endpos=lsn
           In --start mode, automatically stop replication and exit with normal exit status 0
           when receiving reaches the specified LSN. If specified when not in --start mode, an
           error is raised.

           If there's a record with LSN exactly equal to lsn, the record will be output.

           The --endpos option is not aware of transaction boundaries and may truncate output
           partway through a transaction. Any partially output transaction will not be consumed
           and will be replayed again when the slot is next read from. Individual messages are
           never truncated.

       -f filename
       --file=filename
           Write received and decoded transaction data into this file. Use - for stdout.

       -F interval_seconds
       --fsync-interval=interval_seconds
           Specifies how often pg_recvlogical should issue fsync() calls to ensure the output
           file is safely flushed to disk.

           The server will occasionally request the client to perform a flush and report the
           flush position to the server. This setting is in addition to that, to perform flushes
           more frequently.

           Specifying an interval of 0 disables issuing fsync() calls altogether, while still
           reporting progress to the server. In this case, data could be lost in the event of a
           crash.

       -I lsn
       --startpos=lsn
           In --start mode, start replication from the given LSN. For details on the effect of
           this, see the documentation in Chapter 48 and Section 52.4. Ignored in other modes.

       --if-not-exists
           Do not error out when --create-slot is specified and a slot with the specified name
           already exists.

       -n
       --no-loop
           When the connection to the server is lost, do not retry in a loop, just exit.

       -o name[=value]
       --option=name[=value]
           Pass the option name to the output plugin with, if specified, the option value value.
           Which options exist and their effects depends on the used output plugin.

       -P plugin
       --plugin=plugin
           When creating a slot, use the specified logical decoding output plugin. See
           Chapter 48. This option has no effect if the slot already exists.

       -s interval_seconds
       --status-interval=interval_seconds
           This option has the same effect as the option of the same name in pg_receivewal(1).
           See the description there.

       -S slot_name
       --slot=slot_name
           In --start mode, use the existing logical replication slot named slot_name. In
           --create-slot mode, create the slot with this name. In --drop-slot mode, delete the
           slot with this name.

       -v
       --verbose
           Enables verbose mode.

       The following command-line options control the database connection parameters.

       -d database
       --dbname=database
           The database to connect to. See the description of the actions for what this means in
           detail. This can be a libpq connection string; see Section 33.1.1 for more
           information. Defaults to user name.

       -h hostname-or-ip
       --host=hostname-or-ip
           Specifies the host name of the machine on which the server is running. If the value
           begins with a slash, it is used as the directory for the Unix domain socket. The
           default is taken from the PGHOST environment variable, if set, else a Unix domain
           socket connection is attempted.

       -p port
       --port=port
           Specifies the TCP port or local Unix domain socket file extension on which the server
           is listening for connections. Defaults to the PGPORT environment variable, if set, or
           a compiled-in default.

       -U user
       --username=user
           User name to connect as. Defaults to current operating system user name.

       -w
       --no-password
           Never issue a password prompt. If the server requires password authentication and a
           password is not available by other means such as a .pgpass file, the connection
           attempt will fail. This option can be useful in batch jobs and scripts where no user
           is present to enter a password.

       -W
       --password
           Force pg_recvlogical to prompt for a password before connecting to a database.

           This option is never essential, since pg_recvlogical will automatically prompt for a
           password if the server demands password authentication. However, pg_recvlogical will
           waste a connection attempt finding out that the server wants a password. In some cases
           it is worth typing -W to avoid the extra connection attempt.

       The following additional options are available:

       -V
       --version
           Print the pg_recvlogical version and exit.

       -?
       --help
           Show help about pg_recvlogical command line arguments, and exit.

ENVIRONMENT

       This utility, like most other PostgreSQL utilities, uses the environment variables
       supported by libpq (see Section 33.14).

EXAMPLES

       See Section 48.1 for an example.

SEE ALSO

       pg_receivewal(1)