Provided by: libsane_1.0.17-1ubuntu4_i386 bug


       sane-gphoto2 - SANE backend for gphoto2 supported cameras


       The  sane-gphoto2  library  implements a SANE (Scanner Access Now Easy)
       backend that provides  access  to  the  digital  cameras  supported  by
       gphoto2.   This  backend has only been tested with a handful of cameras
       so far.  Patches to support other models are welcome.

       Because of the limited testing of this backend, it is commented out  in
       /etc/sane.d/dll.conf  by default.  Either the comment character must be
       removed or the backend must be called explicitly.  E.g.  ‘scanimage  -d
       gphoto2’ or ‘xscanimage gphoto2’.


       The  current  version  of  the  backend  only  allows  one camera to be
       connected.  The device name is always "0".


       The contents of the gphoto2.conf specify  the  characteristics  of  the
       camera  to be used.   Resolutions (high resolution, low resolution, and
       thumbnail size)  are  required  since  they  are  needed  by  the  sane
       frontends,  but can’t be obtained through the gphoto2 interface.  Valid
       ports and cameras can  be  obtained  by  "gphoto2  --list-cameras"  and
       "gphoto2 --list-ports".

       The  dumpinquiry  line  causes  some information about the camera to be

       Empty lines and lines starting with a hash mark  (#)  are  ignored.   A
       sample configuration file is shown below:

       The  "topfolder" line specifies the "fixed" part of the file path.  For
       example, on the  Kodak  DC-240,  files  are  stored  in  the  directory
       /DCIM/100DC240.   The  /DCIM  portion  is  constant,  but 100DC240 will
       change and must be read from the camers.  In this case, the line  would
       read "topfolder=/DCIM"

       Some cameras don’t implement a file structure and store all pictures in
       the "/" directory.  This  is  indicated  by  setting  "subdirs=0"  with

              camera=Kodak DC240
              # this is a comment


              The   backend   configuration  file  (see  also  description  of
              SANE_CONFIG_DIR below).

              The static library implementing this backend.

              The shared library implementing this backend (present on systems
              that support dynamic loading).


              This environment variable specifies the list of directories that
              may contain the configuration file.  Under UNIX, the directories
              are  separated  by a colon (‘:’), under OS/2, they are separated
              by a semi-colon  (‘;’).   If  this  variable  is  not  set,  the
              configuration  file  is  searched  in  two  default directories:
              first,  the  current  working  directory  (".")  and   then   in
              /etc/sane.d.  If the value of the environment variable ends with
              the directory separator character, then the default  directories
              are  searched  after  the explicitly specified directories.  For
              example, setting SANE_CONFIG_DIR to "/tmp/config:" would  result
              in   directories  "tmp/config",  ".",  and  "/etc/sane.d"  being
              searched (in this order).

              If the library was compiled with debugging support enabled, this
              environment  variable controls the debug level for this backend.
              A value of 128 requests maximally copious debug output;  smaller
              levels reduce verbosity.

              Set  to 1, 2, or 3, to enable various levels of debugging within
              the gphoto2 libraries.




       Peter S. Fales

       The manpage was largeley copied from the dc210 manpage.


       Many, no doubt.

       More general comments, suggestions, and inquiries  about  frontends  or
       SANE   should   go   to   the   SANE   Developers   mailing  list  (see for details).  You  must
       be  subscribed  to  the  list, otherwise your mail won’t be sent to the