Provided by: isdnactivecards_3.8.2005-12-06-2ubuntu4_i386 bug

NAME

       divaload - configure Eicon Diva active ISDN card

SYNOPSIS

       divaload controller protocol [options]

DESCRIPTION

       divaload  is  used  to  setup  the  Eicon  Diva  card  for  the  proper
       configuration.

OPTIONS

       controller
              selects the controller (card). This can be either:
              -c n
              where n is the controller number, or
              -all
              to operate on all cards.

       protocol
              can be one of the following:
                -f 1TR6     Germany, old protocol for PABX................ PRI & BRI
                -f ETSI     DSS1, Europe (Germany, ...)................... PRI & BRI
                -f FRANC    VN3, France, old protocol for PABX............ PRI & BRI
                -f BELG     NET3, Belgien, old protocol for PABX.......... PRI & BRI
                -f SWED     DSS1 with CRC4 off, Sweden, Benelux........... PRI
                -f NI       NI1, NI2, North America, National ISDN........ PRI & BRI
                -f 5ESS     5ESS, North America, AT&T..................... PRI & BRI
                -f JAPAN    Japan, INS-NET64.............................. PRI & BRI
                -f ATEL     ATEL, Australia, old TPH1962.................. PRI & BRI
                -f US       North America, Auto Detect....................       BRI
                -f ITALY    DSS1, Italy................................... PRI & BRI
                -f TWAN     DSS1, Taiwan.................................. PRI & BRI
                -f AUSTRAL  Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI
                -f 4ESS_SDN 4ESS Software Defined Network................. PRI
                -f 4ESS_SDS 4ESS Switched Digital Service................. PRI
                -f 4ESS_LDS 4ESS Long Distance Service.................... PRI
                -f 4ESS_MGC 4ESS Megacom.................................. PRI
                -f 4ESS_MGI 4ESS Megacom International.................... PRI
                -f HONGKONG Hongkong...................................... PRI & BRI
                -f RBSCAS   Robbed Bit Signaling, CAS..................... PRI
                -f QSIG     QSIG, Intra PABX link protocol................ PRI & BRI

       The following options may be given to divaload.

       -e [1,2,3]
              set Layer 1 framing on PRI Adapter

              1 - doubleframing (NO CRC4)
              2 - multiframing (CRC4)
              3 - autodetection

       -x     set PRI Adapter in NT mode; default mode is TE

       -z     set PRI  Adapter  in  High  Impedance  state  until  first  user
              application does request interface activation

       -l [1...30]
              set  starting  channel  number  on  PRI Adapter.  By default the
              allocation of channels is  made  on  a  high-to-low  basis.   By
              specifying  -l  you  select  a low-to-high allocation policy (in
              addition)

       -q [0..3]
              select QSIG options

              0 - CR and CHI 2 Bytes long (default)
              1 - CR 1 byte, CHI 2 bytes
              2 - CR is 2 bytes, CHI is 1 byte
              3 - CR and CHI 1 byte
              (CR - Call Reference, CHI - B-Channel Ident.)

       -n [0...20]
              select NT2 mode and default length of DIDN (DIDN - Direct Inward
              Dial Number)

       -o     turn off order checking of information elements

       -p [1,2]
              establish    a    permanent   connection   (e.g.   leased   line
              configuration)

              1 - TE <-> TE mode, structured line
              2 - NT <-> TE mode, raw line

       -s [0,1,2,3]
              D-Channel Layer 2 activation policy on BRI Adapter

              0 - On demand
              1 - Deactivation only by NT side, preferred, default
              2 - Always active
              3 - Always active, mode 2

       -t [0...63]
              specifies  a  fixed  TEI  value  (Default  is  a  automatic  TEI
              assignment)

       -u     select point to point mode on BRI Adapter; uses default TEI ’0’,
              NT2 mode is on

       -[1...8]oad|osa|spid
              BRI Adapter B-Channel options Specify  the  Originating  Address
              (OAD),  Originating  Sub-address  (OSA)  and/or  Service Profile
              Identifier (SPID) for each B-channel (1 or 2 by  BRI,  1...8  by
              4BRI)
              Example: -1oad 123456 -1spid 1234560001

       -d     display protocol options summary

       -w     select alternative protocol code directory.
              default directory: "/usr/share/isdn"

       -h or -?
              help

AUTHOR

       manpage written from -h output by Paul Slootman <paul@debian.org>.