Provided by: bluez-utils_2.24-0ubuntu6_i386 bug

NAME

       hciconfig - configure Bluetooth devices

SYNOPSIS

       hciconfig -h
       hciconfig [-a]
       hciconfig [-a] <hciX> [command [command parameters]]

DESCRIPTION

       hciconfig is used to configure Bluetooth devices. <hciX> is the name of
       a Bluetooth device installed in the system. If  <hciX>  is  not  given,
       hciconfig  prints  name  and  basic information about all the Bluetooth
       devices installed in the system. If <hciX> is given but no  command  is
       given,  it  prints  basic  information  on  device  <hciX>  only. Basic
       information is interface type, BD address, ACL MTU, SCO MTU, flags (up,
       init,  running,  raw, page scan enabled, inquiry scan enabled, inquiry,
       authentication enabled, encryption enabled).

OPTIONS

       -h     Gives a list of possible commands.

       -a     Other than the basic info, print  features,  packet  type,  link
              policy, link mode, name, class, version.

COMMANDS

       up     Open and initialize HCI device.

       down   Close HCI device.

       reset  Reset HCI device.

       rstat  Reset statistic counters.

       auth   Enable authentication (sets device to security mode 3).

       noauth Disable authentication.

       encrypt
              Enable encryption (sets device to security mode 3).

       noencrypt
              Disable encryption.

       secmgr Enable security manager (current kernel support is limited).

       nosecmgr
              Disable security manager.

       piscan Enable page and inquiry scan.

       noscan Disable page and inquiry scan.

       iscan  Enable inquiry scan, disable page scan.

       pscan  Enable page scan, disable inquiry scan.

       ptype [type]
              With no type , displays the current packet types. Otherwise, all
              the packet types specified by type are set.  type  is  a  comma-
              separated  list of packet types, where the possible packet types
              are DM1, DM3, DM5, DH1, DH3, DH5, HV1, HV2, HV3.

       name [name]
              With no name, prints local name. Otherwise, sets local  name  to
              name.

       class [class]
              With  no class, prints class of device. Otherwise, sets class of
              device to class.  class is a 24-bit hex  number  describing  the
              class  of  device,  as specified in section 1.2 of the Bluetooth
              Assigned Numers document.

       voice [voice]
              With no voice,  prints  voice  setting.  Otherwise,  sets  voice
              setting  to  voice.  voice is a 16-bit hex number describing the
              voice setting.

       iac [iac]
              With no iac, prints the current IAC setting. Otherwise, sets the
              IAC to iac.

       inqmode [mode]
              With  no  mode,  prints out the current inquiry mode. Otherwise,
              sets inquiry mode to mode.

       inqdata [data]
              With no name, prints out the current  inquiry  data.  Otherwise,
              sets inquiry data to data.

       inqtype [type]
              With  no  type,  prints  out  the  current  inquiry  scan  type.
              Otherwise, sets inquiry scan type to type.

       inqparms [win:int]
              With no  win:int,  prints  inquiry  scan  window  and  interval.
              Otherwise,  sets  inquiry  scan  window to win slots and inquiry
              scan interval to int slots.

       pageparms [win:int]
              With  no  win:int,  prints  page  scan  window   and   interval.
              Otherwise,  sets  page  scan  window  to win slots and page scan
              interval to int slots.

       pageto [to]
              With no to, prints page timeout. Otherwise, sets page timeout to
              to slots.

       afhmode [mode]
              With  no  mode, prints out the current AFH mode. Otherwise, sets
              AFH mode to mode.

       aclmtu <mtu:pkt>
              Sets ACL MTU to to mtu bytes and ACL buffer size to pkt packets.

       scomtu <mtu:pkt>
              Sets SCO MTU to to mtu bytes and SCO buffer size to pkt packets.

       putkey <bdaddr>
              This command stores the link key for bdaddr on the device.

       delkey <bdaddr>
              This command deletes the stored link key  for  bdaddr  from  the
              device.

       commands
              Display supported commands.

       features
              Display device features.

       version
              Display version information.

       revision
              Display revision information.

       lm [mode]
              With  no  mode  ,  prints  link  mode.   MASTER  or  SLAVE mean,
              respectively, to ask to become master or to remain slave when  a
              connection request comes in. The additional keyword ACCEPT means
              that baseband  connections will be accepted even if there are no
              listening  AF_BLUETOOTH  sockets.   mode  is  NONE  or  a comma-
              separated list of keywords, where possible keywords  are  MASTER
              and  ACCEPT .  NONE sets link policy to the default behaviour of
              remaining slave and  not  accepting  baseband  connections  when
              there  are  no  listening  AF_BLUETOOTH  sockets.  If  MASTER is
              present, the device will ask to become master  if  a  connection
              request  comes  in. If ACCEPT is present, the device will accept
              baseband  connections  even  when   there   are   no   listening
              AF_BLUETOOTH sockets.

AUTHORS

       Written  by  Maxim  Krasnyansky <maxk@qualcomm.com> and Marcel Holtmann
       <marcel@holtmann.org>

       man page by Fabrizio Gennari <fabrizio.gennari@philips.com>