Provided by: mii-diag_2.11-1_i386 bug

NAME

       mii-diag - Network adapter control and monitoring

SYNOPSIS

       mii-diag [options]<interface>

DESCRIPTION

       This manual page documents briefly the mii-diag network adapter control
       and monitoring  command.   Addition  documentation  is  available  from
       http://scyld.com/diag/index.html.

       This mii-diag command configures, controls and monitors the transceiver
       management registers for  network  interfaces,  and  configures  driver
       operational  parameters.   For  transceiver  control  mii-diag uses the
       Media Independent Interface (MII) standard (thus the command name).  It
       also  has  additional Linux-specific controls to communicate parameters
       such as message enable settings and  buffer  sizes  to  the  underlying
       device driver.

       The  MII  standard  defines  registers  that control and report network
       transceiver capabilities, link settings and errors.  Examples are  link
       speed,  duplex, capabilities advertised to the link partner, status LED
       indications and link error counters.

OPTIONS

       The mii-diag command supports both single  character  and  long  option
       names.   Short  options  use a single dash (´-´) in front of the option
       character.  For options without parameters,  multiple  options  may  be
       concatenated  after  a  single  dash.  Long options are prefixed by two
       dashes (´--´), and may be abbreviated with a  unique  prefix.   A  long
       option may take a parameter of the form --arg=param or --arg param.

       A summary of options is as follows.

       -A, --advertise <speed|setting>
               -F, --fixed-speed <speed|setting>

              Speed  is one of: 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-
              HD, 10baseT, 10baseT-FD, 10baseT-HD.  For more  precise  control
              an explict numeric register setting is also allowed.

       -a, --all-interfaces
              Show   the  status  of  all  interfaces.   This  option  is  not
              recommended with any other option, especially ones  that  change
              settings.

       -s,--status
              Return exit status 2 if there is no link beat.

       -D     Increase  the  debugging  level.  This may be used to understand
              the actions the command is taking.

       -g, --read-parameters
              Show driver-specific parameters.

       -G, --set-parameters value[,value...]
              Set  driver-specific   parameters.    Set   a   adapter-specific
              parameters.    Parameters  are  comma  separated,  with  missing
              elements retaining the existing value.

       -v     Increase the verbosity level.  Additional "-v" options  increase
              the level further.

       -V     Show the program version information.

       -w, --watch
              Continuously monitor the transceiver and report changes.

       -?     Emit usage information.

DESCRIPTION

       Calling  the  command  with  just the interface name (which defaults to
       capabilities, configuration and current status.

       The ’--monitor’ option allows scripting link beat changes.

       This option  is  similar  to  --watch,  but  with  lower  overhead  and
       simplifed  output.   It  polls the interface only once a second and the
       output format is a single line per link change with three fixed words
         <unknown|down||negotiating|up> <STATUS> <PARTNER-CAP>

       Example output:  mii-diag --monitor eth0
          down         0x7809 0x0000
          negotiating  0x7829 0x45e1
          up           0x782d 0x45e1
          down         0x7809 0x0000

       This may be used as
         mii-diag --monitor eth0 |
           while read linkstatus bmsr linkpar; do
            case $linkstatus in
               up)   ifup eth0 ;;
               down) ifdown eth0 ;;
            esac
           done

       It may be useful to shorten the DHCP client daemon timeout if  it  does
       not   receive   an   address   by   adding  the  following  setting  to
       /etc/sysconfig/network: DHCPCDARGS="-t 3"

SEE ALSO

       ether-wake(8),net-diag(8),mii-tool(8).
       Addition        documentation         is         available         from
       http://scyld.com/diag/index.html.

KNOWN BUGS

       The  --all-interfaces  option  is  quirky.  There are very few settings
       that are usefully applied to all interfaces.

AUTHOR

       The manual pages, diagnostic commands, and many of the underlying Linux
       network  drivers were written by Donald Becker for the Scyld Beowulf(™)
       cluster system.