Provided by: picocom_1.4-1_i386 bug

NAME

       picocom - minimal dumb-terminal emulation program

SYNOPSIS

       picocom [ options ] device

DESCRIPTION

       As  its  name  suggests,  picocom  is a minimal dumb-terminal emulation
       program. It is, in principle, very much like  minicom(1)  ,  only  it’s
       "pico" instead of "mini"! It was designed to serve as a simple, manual,
       modem configuration, testing, and debugging tool. It  has  also  served
       (quite   well)  as  a  low-tech  "terminal-window"  to  allow  operator
       intervention in PPP connection scripts (something like  the  ms-windows
       "open  terminal  window before / after dialing" feature). It could also
       prove useful in many other similar tasks.

       When picocom starts it opens the terminal (serial device) given as  its
       non-option argument. Unless the --noinit option is given, it configures
       the device to the settings specified by  the  option-arguments  (or  to
       some  default  settings),  and  sets  it  to "raw" mode. If --noinit is
       given, the initialization and configuration is skipped; the  device  is
       just  opened.  Following  this,  picocom  sets  the  standard-input and
       standard-output to raw mode. Having done so, it goes in a loop where it
       listens  for  input from stdin, or from the serial port. Input from the
       serial port is copied to the  standard  output  while  input  from  the
       standard  input  is  copied to the serial port.  picocom also scans its
       input stream for a user-specified control character, called the "escape
       character"  (being  by default "C-a"). If the escape character is seen,
       then instead of sending it to the  serial-device,  the  program  enters
       "command  mode"  and  waits for the next character (which is called the
       "function  character").  Depending  on  the  value  of   the   function
       character,  picocom  performs  one  of  the operations described in the
       "Commands" section below.

COMMANDS

       Commands are given to picocom by first keying  the  "espace  character"
       which  by  default  is "C-a" (see "Options" below on how to change it),
       and then keying one for the function (command) characters shown here.

       [escape character]
          Send  the  escape  character  to  the  serial  port  and  return  to
          "transparent"  mode. This means that if the escape character ("C-a",
          by default) is typed twice, the program sends the  escape  character
          to  the  serial port, and remains in transparent mode. This is a new
          behavior implemented in v1.4. Previously picocom used to ignore  the
          escape-character when it was entered as a function character.

       C-x
          Exit  the  program: if the "--noreset" option was not given then the
          serial port is reset to its original settings before exiting; if  it
          was given the serial port is not reset.

       C-q
          Quit  the  program *without* reseting the serial port, regardless of
          the "--noreset" option.

       C-p
          Pulse the DTR line. Lower it for 1 sec, and then raise it again.

       C-t
          Toggle the DTR line. If DTR is up, then lower it.  If  it  is  down,
          then raise it.

       C-\
          Generate  a  break  sequence on the serial line. A break sequence is
          usually generated by marking (driving to logical one) the serial  Tx
          line  for  an  amount  of  time  coresponding  to  several character
          durations.

       C-u
          Baud up. Increase the baud-rate. The  list  of  baud-rates  stepped-
          through by this command is: 300, 600, 1200, 2400, 4800, 9600, 19200,
          38400, 57600, 115200.

       C-d
          Baud down. Decrease the baud-rate. The list of  baud-rates  stepped-
          through by this command is the same as for the "baud-up" command.

       C-f
          Cycle through flow-control settings (RTS/CTS, XON/XOFF, none).

       C-y
          Cycle through parity settings (even, odd, none).

       C-b
          Cycle through databits-number settings (5, 6, 7, 8).

       C-v
          Show  program  options  (like  baud  rate, data bits, etc). Only the
          options that can be modified online (through  commands)  are  shown,
          not those that can only be set at the command-line.

       C-s
          Send (upload) a file (see "Sending and Receiving Files" below)

       C-r
          Receive (download) a file (see "Sending and Receiving Files" below)

       After  performing  one  of  the above operations the program leaves the
       command mode and enters transparent  mode.  Example:  To  increase  the
       baud-rate by two steps, you have to type:

       C-a, C-u, C-a, C-u

       assuming of-course that "C-a" is the escape character.

SENDING AND RECEIVING FILES

       picocom  can send and receive files over the serial port using external
       programs that implement the  respective  protocols.  In  Linux  typical
       programs for this purpose are:

       —  rx(1) - receive using the X-MODEM protocol

       —  rb(1) - receive using the Y-MODEM protocol

       —  rz(1) - receive using the Z-MODEM protocol

       —  sx(1) - send using the X-MODEM protocol

       —  sb(1) - send using the Y-MODEM protocol

       —  sz(1) - send using the Z-MODEM protocol

       —  ascii-xfr(1) - receive or transmit ASCII files

       The  name  of,  and the command-line options to, the program to be used
       for transmitting files are given by the "--send-cmd" option.  Similarly
       the  program  to  receive  files,  and  its  argumets, are given by the
       "--receive-cmd" option. For  example,  in  order  to  start  a  picocom
       session that uses "sz" to transmit files, and "rz" to receive, you have
       to say something like this:

       picocom --send-cmd "sz -vv" --receive-cmd "rz -vv"

       During the picocom session, if you key the "send" or "receive" commands
       (e.g.  by  pressing  C-a,  C-s, or C-a, C-r) you will be prompted for a
       filename. At this prompt you can enter one or more file-names, and  any
       additional  arguments  to  the transmission or reception program. After
       that, picocom will start the the external program as specified  by  the
       "--send-cmd",  or  "--receive-cmd"  option,  and with any filenames and
       additional arguments you may have  supplied.  The  standard  input  and
       output  of  the  external program will be connected to the serial port.
       The standard error of the external program will  be  connected  to  the
       terminal   which---while   the  program  is  running---will  revert  to
       canonical mode. Pressing ’C-c’ while the external  program  is  running
       will prematurely terminate it, and return control to picocom

OPTIONS

       picocom accepts the following command-line options

       --baud | -b
          Defines the baud-rate to set the serial-port (terminal) to.

       --flow | -f
          Defines the flow-control mode to set the serial-port to. Must be one
          of:

          —  ´x’ for xon/xoff (software) mode

          —  ´h’ for hardware flow control (RTS/CTS)

          —  ´n’ for no flow control

          (Default: ’n’)

       --parity | -p
          Defines the parity mode to set the serial-port to. Must be one of:

          —  ´o’ for odd parity mode.

          —  ´e’ for even parity mode.

          —  ´n’ for no parity, mode.

          (Default: ’n’)

       --databits | -d
          Defines the number of data bits in every character. Must be one  of:
          5, 6, 7, 8

          (Default: 8)

       --esacpe | -e
          Defines the character that will make picocom enter command-mode (see
          description above). If ’x’ is given,  then  C-x  will  make  picocom
          enter command mode.

          (Default: ’a’)

       --noinit | -i
          If  given,  picocom  will not initialize, reset, or otherwise meddle
          with the serial port at start-up. It will  just  open  it.  This  is
          useful,  for  example,  for  connecting picocom to already-connected
          modems,  or  already  configured  ports  without   terminating   the
          connection,  or  altering  the  settings.  If  required  serial port
          parameters can then be adjusted at run-time by commands.

       --noreset | -r
          If given, picocom will not *reset* the serial port when exiting.  It
          will just close the filedes and do nothing more. This is useful, for
          example, for leaving modems connected when exiting  picocom  picocom
          using the "Quit" command (instead of "Exit"), which never resets the
          serial port. If "--noreset" is given then "Quit" and  "Exit"  behave
          essentially the same.

       --nolock | -l
          If  given, picocom will *not* attempt to lock the serial port before
          opening it. Normally picocom attempts to get a UUCP-style  lock-file
          (e.g. "/var/lock/LCK..ttyS0") before opening the port. Failing to do
          so, results in the program exiting after emitting an  error-message.
          It  is  possible  that  your picocom binary is compiled without this
          option.

       --send-cmd | -s
          Specifies the external program (and any arguments to it)  that  will
          be used for transmitting files.

          Default: "sz -vv"

       --receive-cmd | -v
          Specifies  the  external program (and any arguments to it) that will
          be used for receiving files.

          (Default: "rz -vv")

       --help | -h
          Print a short help message describing the command-line options.

AUTHOR

       picocom was written by Nick Patavalis (npat@efault.net)

AVAILABILITY

       The   latest   version   of   "picocom"   can   be   downloaded   from:
       http://efault.net/npat/hacks/picocom/

                                                                    picocom(8)