Provided by: libsane-common_1.0.27-3.2ubuntu3_all bug


       sane-st400 - SANE backend for Siemens ST/Highscan flatbed scanners


       The  sane-st400  library implements a SANE (Scanner Access Now Easy) backend that provides
       access to Siemens ST400 flatbed scanners  and  compatibles.   At  present,  the  following
       scanners are supported by this backend:

              Siemens ST400 (6 bit gray scale)
              Siemens ST800 (6 bit gray scale)

       The driver supports line art and gray scans up to 8bpp.

       The Siemens ST/Highscan series includes several more models, e.g. the ST300 and ST600.  If
       you own one of these scanners, or a scanner other than the ones listed  above  that  works
       with  this  backend,  please let us know by sending the scanner's model name, SCSI ID, and
       firmware   revision   to     Have    a    look    at concerning subscription to sane-devel.


       This backend expects device names of the form:


       Where  special  is  either the path-name for the special device that corresponds to a SCSI
       scanner. For SCSI scanners, the special device name must be a generic  SCSI  device  or  a
       symlink  to such a device.  Under Linux, such a device name could be /dev/sga or /dev/sge,
       for example.  See sane-scsi(5) for details.


       The contents of the st400.conf file is a list of device names that correspond  to  Siemens
       scanners.   Empty  lines  and  lines  starting with a hash mark (#) are ignored.  A sample
       configuration file is shown below:

              # this is a comment

       The default configuration file that is distributed with SANE looks like this:

              scsi SIEMENS "ST 400" Scanner * * 3 0

       In this configuration, the driver can only access the ST400 model at SCSI ID 3 LUN 0  (see
       section "BUGS" below for the reason).  To use the driver with other scanner models, add an
       appropriate line to the configuration file.  For example, to use it with an ST800 at  SCSI
       ID 3 LUN 0, add the line:

              scsi SIEMENS "ST 800" Scanner * * 3 0


              The backend configuration file (see also description of SANE_CONFIG_DIR below).

              The static library implementing this backend.

              The  shared  library  implementing  this  backend  (present on systems that support
              dynamic loading).


              This environment variable specifies the list of directories that  may  contain  the
              configuration  file.   Under  UNIX, the directories are separated by a colon (`:'),
              under OS/2, they are separated by a semi-colon (`;').  If this variable is not set,
              the  configuration  file is searched in two default directories: first, the current
              working directory (".") and then in /etc/sane.d.  If the value of  the  environment
              variable  ends with the directory separator character, then the default directories
              are searched after the explicitly  specified  directories.   For  example,  setting
              SANE_CONFIG_DIR  to  "/tmp/config:"  would result in directories "tmp/config", ".",
              and "/etc/sane.d" being searched (in this order).

              If the library was compiled with debug support enabled, this  environment  variable
              controls  the debug level for this backend. E.g., a value of 128 requests all debug
              output to be printed. Smaller levels reduce verbosity.


       Everything but the most basic stuff.


       Currently, the backend does not check if the attached device really is a ST400.   It  will
       happily  accept  everything that matches the configuration entries.  This makes it easy to
       test the backend with other scanners: Just add an appropriate line  to  the  configuration
       file.   The  configuration  file as distributed (see above) only works with the ST400.  Be
       careful: If there is no config file at all, the backend defaults to /dev/scanner.

       The ST400 answers on all eight SCSI LUNs.  Normally this is not a problem, as LUN  support
       is  usually  disabled  in  SCSI  drivers,  but if you are seeing multiple instances of the
       scanner in a device list, either disable LUNs in your SCSI setup or change  the  entry  in
       the configuration file to match LUN 0 only.


       If you encounter a bug please set the environment variable SANE_DEBUG_ST400 to 128 and try
       to regenerate the problem. Then send me a report with the log attached.

       If you encounter a SCSI bus error or trimmed and/or displaced images please also  set  the
       environment variable SANE_DEBUG_SANEI_SCSI to 128 before sending me the report.


       sane(7), sane-scsi(5)


       Ingo Wilken <>

@PACKAGEVERSION@                           14 Jul 2008                              sane-st400(5)