Provided by: dar_2.6.8-1_amd64 
NAME
dar_split - dar helper to split an archive over several tapes
SYNOPSIS
dar_split { split_input | [-s] split_output } <filename>
dar_split -v
dar_split -h
DESCRIPTION
dar_split is to be used with dar to read or write a large archive from or to several
tapes.
COMMANDS
dar_split has two modes of operation: split_input and split_output
split_input in this mode dar_split copies <filename> to its standard output.
<filename> may be a special device like /dev/tape or any other inode
that has the ability to access removeable volumes. When dar_split
reaches the end of <filename> it suspends and waits for the user to
press the return key in order to continue. In the meanwhile the user
can rewind and change the tape. When dar_split is awaken again, it
reopens <filename> and sends its content to its standard output as if
it was the continuation of what was read so far before reaching the
end of file.
split_output in this mode dar_split copies its standard input to <filename>.
However if <filename> is full, dar_split suspends and waits for the
user to press the return key in order to continue. In the meanwhile,
the user can rewind and change the tape. When dar_split is awaken
again, it reopens <filename> and continues to copy to <filename> what
was not yet written previously.
OPTIONS
-s is only available for split_output mode an leads dar_split to perform sync writes in
place of normal writes. This has the drawback to drastically reduce performances but may
be necessary under certain circumstances where the operating system cache reports a write
operation as successful while the cache underlying medium is already full.
EXAMPLES OF USE
creating an archive over several tapes
dar -c - ...possibily other dar options... | dar_split split_output /dev/tape
Here dar generates the archive to its standard output which is read by dar_split and
copied to /dev/tape. When the tape reaches its send, dar_split asks for the user to hit
return to continue.
reading an archive splitted over several tapes
dar_split split_input /dev/tape | dar -t - --sequential-read ...possibily other dar
options...
Here dar_split reads /dev/tape and sends its content to dar which *must* be used in
--senquential-read mode in order to read an archive from its standard input without the
help of dar_slave. When the tape reaches its end, dar_split asks for the user to hit
return to continue.
Note that dar_split can also be used with tar for the same purpose as with dar:
tar -cz ... | dar_split split_output /dev/tape
without -f option nor TAPE environment variable, tar sends the tar archive to stdout,
which get fet to dar_split for slicing
dar_split split_input /dev/tape | tar -tz
without -f option nor TAPE environement variable, tar read the tar archive from stdin,
however you must specify the correct option corresponding to the compression used at
archive creation time.
The advantage here is to be able to save a huge dar or tar archive on several tapes that
could be either partially filled or having different sizes, without having to calculate in
advance the size of slices to specify. The drawback is that this implies sequential
reading for dar (for tar also, but tar cannot do else).
With or without filesystem
You can use dar_split with floppies, zip/jazz disks or usb key too, but it has many
disadvantages compared to the normal way of using this media: doing that way avoids you
relying on a filesystem, thus you cannot have direct access to file contents, which dar
knows how to take advantage of, and you are instead stuck with sequential read access
which is long as it requires reading the whole archive (same way as tar does).
When instead using dar alone in normal mode (non sequential reading mode using filenames
instead of standard input/output), you have the opportunity to create redundancy data
beside dar slices thanks to par2, which is not possible without a filesystem. At
restoration time, thanks to dar archive's catalog, dar can directly seek to the file's
data you want to restore, which is very quick compared to
reading/unciphering/uncompressing the whole archive...
Note that copying tape contents generated by dar_split to different files which name would
correspond to dar slices, does not make a valid multi-sliced archive because the slice
header is missing in slices (except in the first). You can however concatenate all the
pieces of data generated by dar_split and have a valid single sliced dar archive that you
can use in direct access mode. However attention must be paied not to add any extra data
after data generated by dar through dar_split (in particular if the last tape was not
full), in that case you can only read the archive with --sequential-read mode.
EXIT CODES
dar_split exists with the following codes:
0 upon normal execution
1 syntax error on command-line
2 could not open source or destination files
SIGNALS
Any signal sent to dar_split except SIG_PIPE will abort the program immediately
SEE ALSO
dar(1), dar_xform(1), dar_manager(1), dar_slave(1), dar_cp(1)
KNOWN BUGS
http://sourceforge.net/p/dar/bugs/
AUTHOR
http://dar.linux.free.fr/
Denis Corbin
France
Europe