Provided by: ipmiutil_3.1.5-1_amd64 bug

NAME

       ipmiutil_reset - perform a hardware reset on the system

SYNOPSIS

       ipmiutil reset [-bcdDefhijmnoprsuwxy -N node -U user -P/-R pswd -EFJTVY]

DESCRIPTION

       ipmiutil  reset  is  a  program that uses IPMI commands to perform a hardware reset of the
       chassis, or boot to a specific device.  This utility can use either the /dev/ipmi0  driver
       from  OpenIPMI,  the  /dev/imb  driver  from  Intel, the /dev/ipmikcs driver from valinux,
       direct user-space IOs, or the IPMI LAN interface if -N.

OPTIONS

       Command line options are described below.

       -c     Power Cycle the system chassis

       -d     Power Down the system chassis

       -n     Send NMI to the system

       -u     Power Up the system chassis

       -r     Hard Reset the system chassis

       -D     Do a soft shutdown of the OS, and then power down.  Note that remote soft  shutdown
              (-D -N) for Intel S5000 baseboard requires ipmiutil getevt -a running on the target
              server.

       -o     Do a soft shutdown of the OS, and then reset.  Note that remote soft  shutdown  (-o
              -N)  for  Intel  S5000  baseboard requires ipmiutil getevt -a running on the target
              server.

       -k     Do a cold reset to restart the BMC firmware.

       -m 002000s
              Perform these function for a specific MC  (e.g.  bus  00,  sa  20,  lun  00).   The
              trailing character, if present, indicates SMI addressing if 's', or IPMB addressing
              if 'i' or not present.

       -b     Do a hard reset and reboot to the BIOS Setup menu, for this reboot only.

       -e     Do a hard reset to EFI, if IPMI EFI boot is enabled, for this reboot only.

       -f     Do a hard reset to Floppy/Removable, for this reboot only.

       -h     Do a hard reset to a Hard Disk, for this reboot only.

       -i     Set the boot Initiator mailbox string, usually for PXE use.   The  string  must  be
              less than 78 characters.

       -j     Set the IANA number used for the boot Initiator mailbox string.

       -p     Do a hard reset and network boot to PXE server, for this reboot only.

       -s     Do  a  hard  reset  and reboot to the Service/Diagnostic Partition, for this reboot
              only.  Reboots to the default if no service partition is configured.

       -v     Do a hard reset to DVD/CDROM Media, for this reboot only.

       -w     Wait for BMC ready after a reset before exiting the utility.

       -x     Causes extra debug messages to be displayed.

       -y     Yes, try to persist any boot options used  [-befhprsv].   This  requires  the  IPMI
              firmware  to ask the BIOS to change boot order settings, so it may not be supported
              by all BMC firmware vendors.

       -N nodename
              Nodename or IP address of the remote target system.  If a  nodename  is  specified,
              IPMI  LAN  interface  is  used.  Otherwise the local system management interface is
              used.

       -P/-R rmt_pswd
              Remote password for the nodename given.  The default is a null password.

       -U rmt_user
              Remote username for the nodename given.  The default is a null username.

       -E     Use the remote password from Environment variable IPMI_PASSWORD.

       -F drv_t
              Force the driver type to one of the followng: imb, va,  open,  gnu,  landesk,  lan,
              lan2,  lan2i, kcs, smb.  Note that lan2i means lan2 with intelplus.  The default is
              to detect any available driver type and use it.

       -J     Use  the  specified  LanPlus  cipher   suite   (0   thru   17):   0=none/none/none,
              1=sha1/none/none,   2=sha1/sha1/none,   3=sha1/sha1/cbc128,   4=sha1/sha1/xrc4_128,
              5=sha1/sha1/xrc4_40, 6=md5/none/none, ... 14=md5/md5/xrc4_40.  Default is 3.

       -T     Use a specified IPMI LAN Authentication  Type:  0=None,  1=MD2,  2=MD5,  4=Straight
              Password, 5=OEM.

       -V     Use  a  specified  IPMI  LAN  privilege  level.  1=Callback  level,  2=User  level,
              3=Operator level, 4=Administrator level (default), 5=OEM level.

       -Y     Yes, do prompt the user for the IPMI LAN remote  password.   Alternatives  for  the
              password are -E or -P.

SEE ALSO

       ipmiutil(8)  ialarms(8)  iconfig(8)  icmd(8)  idiscover(8) ievents(8) ifru(8) igetevent(8)
       ihealth(8) ilan(8) isel(8) isensor(8) iserial(8) isol(8) iwdt(8)

WARNINGS

       See http://ipmiutil.sourceforge.net/ for the latest version of ipmiutil and  any  bug  fix
       list.

COPYRIGHT

       Copyright (C) 2009  Kontron America, Inc.

       See the file COPYING in the distribution for more details regarding redistribution.

       This utility is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY.

AUTHOR

       Andy Cress <arcress at users.sourceforge.net>

                                     Version 1.5: 01 Jul 2011                           IRESET(8)