Provided by: freebsd-manpages_6.2-1_all
ahc - Adaptec VL/EISA/PCI SCSI host adapter driver
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
For one or more VL/EISA cards:
For one or more PCI cards:
To allow PCI adapters to use memory mapped I/O if enabled:
To configure one or more controllers to assume the target role:
options AHC_TMODE_ENABLE <bitmask of units>
Alternatively, to load the driver as a module at boot time, place the
following lines in loader.conf(5):
This driver provides access to the SCSI bus(es) connected to the Adaptec
AIC77xx and AIC78xx host adapter chips.
Driver features include support for twin and wide busses, fast, ultra or
ultra2 synchronous transfers depending on controller type, tagged
queueing, SCB paging, and target mode.
Memory mapped I/O can be enabled for PCI devices with the
“AHC_ALLOW_MEMIO” configuration option. Memory mapped I/O is more
efficient than the alternative, programmed I/O. Most PCI BIOSes will map
devices so that either technique for communicating with the card is
available. In some cases, usually when the PCI device is sitting behind
a PCI->PCI bridge, the BIOS may fail to properly initialize the chip for
memory mapped I/O. The typical symptom of this problem is a system hang
if memory mapped I/O is attempted. Most modern motherboards perform the
initialization correctly and work fine with this option enabled.
Individual controllers may be configured to operate in the target role
through the “AHC_TMODE_ENABLE” configuration option. The value assigned
to this option should be a bitmap of all units where target mode is
desired. For example, a value of 0x25, would enable target mode on units
0, 2, and 5. A value of 0x8a enables it for units 1, 3, and 7.
Per target configuration performed in the SCSI-Select menu, accessible at
boot in non-EISA models, or through an EISA configuration utility for
EISA models, is honored by this driver. This includes
synchronous/asynchronous transfers, maximum synchronous negotiation rate,
wide transfers, disconnection, the host adapter’s SCSI ID, and, in the
case of EISA Twin Channel controllers, the primary channel selection.
For systems that store non-volatile settings in a system specific manner
rather than a serial eeprom directly connected to the aic7xxx controller,
the BIOS must be enabled for the driver to access this information. This
restriction applies to all EISA and many motherboard configurations.
Note that I/O addresses are determined automatically by the probe
routines, but care should be taken when using a 284x (VESA local bus
controller) in an EISA system. The jumpers setting the I/O area for the
284x should match the EISA slot into which the card is inserted to
prevent conflicts with other EISA cards.
Performance and feature sets vary throughout the aic7xxx product line.
The following table provides a comparison of the different chips
supported by the ahc driver. Note that wide and twin channel features,
although always supported by a particular chip, may be disabled in a
particular motherboard or card design.
Chip MIPS Bus MaxSync MaxWidth SCBs Features
aic7770 10 EISA/VL 10MHz 16Bit 4 1
aic7850 10 PCI/32 10MHz 8Bit 3
aic7860 10 PCI/32 20MHz 8Bit 3
aic7870 10 PCI/32 10MHz 16Bit 16
aic7880 10 PCI/32 20MHz 16Bit 16
aic7890 20 PCI/32 40MHz 16Bit 16 3 4 5 6 7 8
aic7891 20 PCI/64 40MHz 16Bit 16 3 4 5 6 7 8
aic7892 20 PCI/64 80MHz 16Bit 16 3 4 5 6 7 8
aic7895 15 PCI/32 20MHz 16Bit 16 2 3 4 5
aic7895C 15 PCI/32 20MHz 16Bit 16 2 3 4 5 8
aic7896 20 PCI/32 40MHz 16Bit 16 2 3 4 5 6 7 8
aic7897 20 PCI/64 40MHz 16Bit 16 2 3 4 5 6 7 8
aic7899 20 PCI/64 80MHz 16Bit 16 2 3 4 5 6 7 8
1. Multiplexed Twin Channel Device - One controller servicing two
2. Multi-function Twin Channel Device - Two controllers on one
3. Command Channel Secondary DMA Engine - Allows scatter gather
list and SCB prefetch.
4. 64 Byte SCB Support - SCSI CDB is embedded in the SCB to
eliminate an extra DMA.
5. Block Move Instruction Support - Doubles the speed of certain
6. ‘Bayonet’ style Scatter Gather Engine - Improves S/G prefetch
7. Queuing Registers - Allows queueing of new transactions
without pausing the sequencer.
8. Multiple Target IDs - Allows the controller to respond to
selection as a target on multiple SCSI IDs.
The ahc driver supports the following SCSI host adapter chips and SCSI
· Adaptec AIC7770 host adapter chip
· Adaptec AIC7850 host adapter chip
· Adaptec AIC7860 host adapter chip
· Adaptec AIC7870 host adapter chip
· Adaptec AIC7880 host adapter chip
· Adaptec AIC7890 host adapter chip
· Adaptec AIC7891 host adapter chip
· Adaptec AIC7892 host adapter chip
· Adaptec AIC7895 host adapter chip
· Adaptec AIC7896 host adapter chip
· Adaptec AIC7897 host adapter chip
· Adaptec AIC7899 host adapter chip
· Adaptec 274X(W)
· Adaptec 274X(T)
· Adaptec 284X
· Adaptec 2910
· Adaptec 2915
· Adaptec 2920
· Adaptec 2930C
· Adaptec 2930U2
· Adaptec 2940
· Adaptec 2940J
· Adaptec 2940N
· Adaptec 2940U
· Adaptec 2940AU
· Adaptec 2940UW
· Adaptec 2940UW Dual
· Adaptec 2940UW Pro
· Adaptec 2940U2W
· Adaptec 2940U2B
· Adaptec 2950U2W
· Adaptec 2950U2B
· Adaptec 19160B
· Adaptec 29160B
· Adaptec 29160N
· Adaptec 3940
· Adaptec 3940U
· Adaptec 3940AU
· Adaptec 3940UW
· Adaptec 3940AUW
· Adaptec 3940U2W
· Adaptec 3950U2
· Adaptec 3960
· Adaptec 39160
· Adaptec 3985
· Adaptec 4944UW
· NEC PC-9821Xt13 (PC-98)
· NEC RvII26 (PC-98)
· NEC PC-9821X-B02L/B09 (PC-98)
· NEC SV-98/2-B03 (PC-98)
· Many motherboards with on-board SCSI support
SCSI CONTROL BLOCKS (SCBs)
Every transaction sent to a device on the SCSI bus is assigned a ‘SCSI
Control Block’ (SCB). The SCB contains all of the information required
by the controller to process a transaction. The chip feature table lists
the number of SCBs that can be stored in on-chip memory. All chips with
model numbers greater than or equal to 7870 allow for the on chip SCB
space to be augmented with external SRAM up to a maximum of 255 SCBs.
Very few Adaptec controller configurations have external SRAM.
If external SRAM is not available, SCBs are a limited resource. Using
the SCBs in a straight forward manner would only allow the driver to
handle as many concurrent transactions as there are physical SCBs. To
fully utilize the SCSI bus and the devices on it, requires much more
concurrency. The solution to this problem is SCB Paging, a concept
similar to memory paging. SCB paging takes advantage of the fact that
devices usually disconnect from the SCSI bus for long periods of time
without talking to the controller. The SCBs for disconnected
transactions are only of use to the controller when the transfer is
resumed. When the host queues another transaction for the controller to
execute, the controller firmware will use a free SCB if one is available.
Otherwise, the state of the most recently disconnected (and therefore
most likely to stay disconnected) SCB is saved, via dma, to host memory,
and the local SCB reused to start the new transaction. This allows the
controller to queue up to 255 transactions regardless of the amount of
SCB space. Since the local SCB space serves as a cache for disconnected
transactions, the more SCB space available, the less host bus traffic
consumed saving and restoring SCB data.
aha(4), ahb(4), cd(4), da(4), sa(4), scsi(4)
The ahc driver appeared in FreeBSD 2.0.
The ahc driver, the AIC7xxx sequencer-code assembler, and the firmware
running on the aic7xxx chips was written by Justin T. Gibbs.
Some Quantum drives (at least the Empire 2100 and 1080s) will not run on
an AIC7870 Rev B in synchronous mode at 10MHz. Controllers with this
problem have a 42 MHz clock crystal on them and run slightly above 10MHz.
This confuses the drive and hangs the bus. Setting a maximum synchronous
negotiation rate of 8MHz in the SCSI-Select utility will allow normal
Although the Ultra2 and Ultra160 products have sufficient instruction ram
space to support both the initiator and target roles concurrently, this
configuration is disabled in favor of allowing the target role to respond
on multiple target ids. A method for configuring dual role mode should
Tagged Queuing is not supported in target mode.
Reselection in target mode fails to function correctly on all high
voltage differential boards as shipped by Adaptec. Information on how to
modify HVD board to work correctly in target mode is available from