Provided by: conserver-server_8.1.16-1_i386
conserver - console server daemon
conserver [-7dDEFhinoRSuvV] [-a type] [-m max] [-M master] [-p port]
[-b port] [-c cred] [-C config] [-P passwd] [-L logfile] [-O min] [-U
Conserver is the daemon that manages remote access to system consoles
by multiple users via the console(1) client program and (optionally)
log the console output. It can connect to consoles via local serial
ports, Unix domain sockets, TCP sockets (for terminal servers and the
like), or any external program.
When started, conserver reads the conserver.cf(5) file for details of
each console. The console type, logging options, serial or network
parameters, and user access levels are just a few of the things that
can be specified. Command-line options are then applied, possibly
overriding conserver.cf(5) settings. Conserver categorizes consoles
into two types: those it should actively manage, and those it should
just know about, so it can refer clients to other conserver instances.
If the master value of a console matches the hostname or ip address of
the local machine, conserver will actively manage the console.
Otherwise, it’s considered a ‘‘remote’’ console and managed by a
different server. Conserver forks a child for each group of consoles
it must manage and assigns each process a port number to listen on.
The maximum number of consoles managed by each child process is set
using the -m option. The console(1) client program communicates with
the master console server process to find the port (and host, in a
multi-server configuration) on which the appropriate child is
listening. Conserver restricts connections from clients based on the
host access section of its conserver.cf(5) file, restricts users based
on the console access lists of the conserver.cf(5) file, and
authenticates users against its conserver.passwd(5) file. Conserver
can also restrict clients using the tcp-wrappers package (enabled using
--with-libwrap). This authentication is done before consulting the
conserver.cf(5) access list.
When Unix domain sockets are used between the client and server
(enabled using --with-uds), authentication checks are done on the
hardcoded address ‘‘127.0.0.1’’. Automatic client redirection is also
disabled (as if the -R option was used) since the client cannot
communicate with remote servers. The directory used to hold the
sockets is checked to make sure it’s empty when the server starts. The
server will not remove any files in the directory itself, just in case
the directory is accidentally specified as ‘‘/etc’’ or some other
critical location. The server will do its best to remove all the
sockets when it shuts down, but it could stop ungracefully (crash,
‘‘kill -9’’, etc) and leave files behind. It would then be up to the
admin (or a creative startup script) to clean up the directory before
the server will start again.
Conserver completely controls any connection to a console. All escape
sequences given by the user to console are passed to the server without
interpretation. The server recognizes and processes all escape
The conserver parent process will automatically respawn any child
process that dies. The following signals are propagated by the parent
process to its children.
SIGTERM Close all connections and exit.
SIGHUP Reread the configuration file. New consoles are managed by
forking off new children, deleted consoles (and their
clients) are dropped, and changes to consoles are done "in
place", resetting the console port (bringing it down and up)
only when necessary. The console name is used to determine
when consoles have been added/removed/changed. All actions
performed by SIGUSR2 are also performed.
SIGUSR1 Try to connect to any consoles marked as down. This can come
in handy if you had a terminal server (or more) that wasn’t
accepting connections at startup and you want conserver to
try to reconnect to all those downed ports.
SIGUSR2 Close and reopen all console logfiles and, if in daemon mode
(-d option), the error logfile (see the -L option). All
actions performed by SIGUSR1 are also performed.
Consoles which have no current client connection might produce
important error messages. With the -u option, these ‘‘unloved’’ errors
are labeled with a machine name and output on stdout (or, in daemon
mode, to the logfile). This allows a live operator or an automated log
scanner to find otherwise unseen errors by watching in a single
Conserver must be run as root if it is to bind to a port under 1024 or
if it must read protected password files (like shadow passwords) for
authentication (see conserver.passwd(5)). Otherwise, it may be run by
any user, with -p used to specify a port above 1024.
If encryption has been built into the code (--with-openssl), encrypted
client connections (without certificate exchanges) happen by default.
To add certificate exchanges, use the -c option with the client and
server. For authentication of the certificates to work, the signing
certificate must be properly trusted, which usually means the public
portion is in OPENSSL_ROOT/ssl/certs (on both the client and server
sides). See the sample self-signing certificate making script
contrib/maketestcerts for further clues. To allow non-encrypted client
connections (in addition to encrypted client connections), use the -E
Options may be given as separate arguments (e.g., -n -d) or clustered
(e.g., -nd). Options and their arguments may be separated by optional
white space. Option arguments containing spaces or other characters
special to the shell must be quoted.
-7 Strip the high bit off of all data received, whether from
the console client or from the console device, before any
-atype Set the default access type for incoming connections from
console clients: ‘r’ for refused (the default), ‘a’ for
allowed, or ‘t’ for trusted. This applies to hosts for
which no matching entry is found in the access section of
-bport Set the base port for children to listen on. Each child
starts looking for free ports at port and working upward,
trying a maximum number of ports equal to twice the maximum
number of groups. If no free ports are available in that
range, conserver exits. By default, conserver lets the
operating system choose a free port.
-ccred Load an SSL certificate and key from the PEM encoded file
-Cconfig Read configuration information from the file config. The
default config may be changed at compile time using the
-d Become a daemon. Disconnects from the controlling terminal
and sends all output (including any debug output) to the
logfile (see -L).
-D Enable debugging output, sent to stderr. Multiple -D
options increases debug output.
-E If encryption has been built into the code (--with-
openssl), encrypted client connections are a requirement.
This option allows non-encrypted clients (as well as
encrypted clients) to connect to consoles.
-F Do not automatically reinitialize failed (unexpectedly
closed) consoles. If the console is a program (‘|’ syntax)
and it closes with a zero exit status, the console is
reinitialized regardless of this option. Without this
option, a console is immediately reopened, and if that
fails, retried every minute until successful. This option
has no effect on the -o and -O options.
-h Output a brief help message.
-i Initiate console connections on demand (and close them when
-Llogfile Log errors and informational messages to logfile after
startup in daemon mode (-d). This option does not apply
when not running in daemon mode. The default logfile may
be changed at compile time using the --with-logfile option.
-mmax Set the maximum consoles managed per process. The default
max may be changed at compile time using the --with-maxmemb
-Mmaster Normally, this allows conserver to bind to a particular IP
address (like ‘127.0.0.1’) instead of all interfaces. The
default is to bind to all addresses. However, if --with-
uds was used to enable Unix domain sockets for
client/server communication, this points conserver to the
directory where it should store the sockets. The default
master directory (‘‘/tmp/conserver’’) may be changed at
compile time using the --with-uds option.
-n Obsolete (now a no-op); see -u.
-o Normally, a client connecting to a ‘‘downed’’ console does
just that. Using this option, the server will
automatically attempt to open (‘‘bring up’’) the console
when the client connects.
-Omin Enable periodic attempts (every min minutes) to open
(‘‘bring up’’) all downed consoles (similar to sending a
SIGUSR1). Without this option, or if min is zero, no
periodic attempts occur.
-pport Set the TCP port for the master process to listen on. This
may be either a port number or a service name. The default
port, ‘‘conserver’’ (typically 782), may be changed at
compile time using the --with-port option. If the --with-
uds option was used, this option is ignored.
-Ppasswd Read the table of authorized user data from the file
passwd. The default passwd may be changed at compile time
using the --with-pwdfile option.
-R Disable automatic client redirection to other conserver
hosts. This means informational commands like -w and -i
will only show the status of the local conserver host and
attempts to connect to remote consoles will result in an
informative message to the user.
-S Do not run the server, just perform a syntax check of
configuration file and exit with a non-zero value if there
is an error. Using more than one -S will cause conserver
to output various information about each console in 5
colon-separated fields, enclosed in curly-braces. The
philosophy behind the output is to provide information to
allow external detection of multiple consoles access the
same physical port. Since this is highly environment-
specific, conserver cannot do the check internally.
name The name of the console.
master The hostname of the master conserver host for the
aliases The console aliases in a comma-separated list.
type The type of console. Values will be a ‘/’ for a
local device, ‘|’ for a command, ‘!’ for a remote
port, ‘%’ for a Unix domain socket, and ‘#’ for a
details Multiple values are comma-separated and depend on
the type of the console. Local devices will have
the values of the device file and baud
rate/parity. Commands will have string to invoke.
Remote ports will have the values of the remote
hostname and port number. Unix domain sockets
will have the path to the socket. Noop consoles
will have nothing.
-u Send unloved console output to conserver’s stdout (which,
in daemon mode, is redirected to the logfile). This
applies to all consoles to which no user is attached,
independent of whether logging of individual consoles is
enabled via conserver.cf entries.
-Ulogfile Copy all console data to the ‘‘unified’’ logfile. The
output is the same as the -u output, but all consoles, not
just those without a user, are logged. Each line of output
is prefixed with the console name. If a user is attached
read/write, a ‘*’ is appended to the console name, to allow
log watching utilites to ignore potential user-introduced
-v Echo the configuration as it is being read (be verbose).
-V Output the version number and settings of the conserver
program and then exit.
The protocol used to interact with the conserver daemon has two basic
styles. The first style is the initial line-based mode, which occurs
before connecting to a console. The second style is the character-
based, escape-sequence mode, while connected to a console.
The initial line-based mode begins the same for both the master process
and its children. Upon a successful (non-rejected) client connection,
an ‘‘ok’’ is sent. The client then issues a command and the server
responds to it with a result string (‘‘ok’’ being the sign of success
for most commands). The commands available are ‘‘help’’, ‘‘ssl’’ (if
SSL was built into the code), ‘‘login’’, and ‘‘exit’’. Using the
‘‘login’’ command, the client authenticates and gains access to the
extended command set. This is where the master process and its
children differ. The master process gives the client access to global
commands, and the child provides commands for interacting with the
consoles it manages. The ‘‘help’’ command, in both cases, will provide
a complete list of commands and a short description of what they do.
The second, character-based, style of interaction occurs when the
client issues the ‘‘call’’ command with a child process. This command
connects the client to a console and, at that point, relays all traffic
between the client and the console. There is no more command-based
interaction between the client and the server, any interaction with the
server is done with the default escape sequence.
This is, by no means, a complete description of the entire
client/server interaction. It is, however, a brief explanation in
order to give a idea of what the program does. See the PROTOCOL file
in the distribution for further details.
The following default file locations may be overridden at compile time
or by the command-line options described above. Run conserver -V to
see the defaults set at compile time.
/etc/conserver.cf description of console terminal lines and
client host access levels; see
/etc/conserver.passwd users allowed to access consoles; see
/var/run/conserver.pid the master conserver process ID
/var/log/conserver log of errors and informational messages
/tmp/conserver directory to hold Unix domain sockets (if
Additionally, output from individual consoles may be logged to separate
files specified in conserver.cf(5).
I’m sure there are bugs, I just don’t know where they are. Please let
me know if you find any.
Thomas A. Fine, Ohio State Computer Science
Kevin S Braunsdorf, Purdue University Computing Center
Bryan Stansell, conserver.com
console(1), conserver.cf(5), conserver.passwd(5)