Provided by: net-tools_1.60-19ubuntu1_i386
route - show / manipulate the IP routing table
route [-v] [-A family] add [-net|-host] target [netmask Nm] [gw Gw]
[metric N] [mss M] [window W] [irtt I] [reject] [mod] [dyn]
[reinstate] [[dev] If]
route [-v] [-A family] del [-net|-host] target [gw Gw] [netmask Nm]
[metric N] [[dev] If]
route [-V] [--version] [-h] [--help]
Route manipulates the kernel’s IP routing tables. Its primary use is
to set up static routes to specific hosts or networks via an interface
after it has been configured with the ifconfig(8) program.
When the add or del options are used, route modifies the routing
tables. Without these options, route displays the current contents of
the routing tables.
use the specified address family (eg ‘inet’; use ‘route --help’
for a full list).
-F operate on the kernel’s FIB (Forwarding Information Base)
routing table. This is the default.
-C operate on the kernel’s routing cache.
-v select verbose operation.
-n show numerical addresses instead of trying to determine symbolic
host names. This is useful if you are trying to determine why
the route to your nameserver has vanished.
-e use netstat(8)-format for displaying the routing table. -ee
will generate a very long line with all parameters from the
del delete a route.
add add a new route.
target the destination network or host. You can provide IP addresses in
dotted decimal or host/network names.
-net the target is a network.
-host the target is a host.
when adding a network route, the netmask to be used.
gw GW route packets via a gateway. NOTE: The specified gateway must
be reachable first. This usually means that you have to set up a
static route to the gateway beforehand. If you specify the
address of one of your local interfaces, it will be used to
decide about the interface to which the packets should be routed
to. This is a BSDism compatibility hack.
set the metric field in the routing table (used by routing
daemons) to M.
mss M set the TCP Maximum Segment Size (MSS) for connections over this
route to M bytes. The default is the device MTU minus headers,
or a lower MTU when path mtu discovery occurred. This setting
can be used to force smaller TCP packets on the other end when
path mtu discovery does not work (usually because of
misconfigured firewalls that block ICMP Fragmentation Needed)
set the TCP window size for connections over this route to W
bytes. This is typically only used on AX.25 networks and with
drivers unable to handle back to back frames.
irtt I set the initial round trip time (irtt) for TCP connections over
this route to I milliseconds (1-12000). This is typically only
used on AX.25 networks. If omitted the RFC 1122 default of 300ms
reject install a blocking route, which will force a route lookup to
fail. This is for example used to mask out networks before
using the default route. This is NOT for firewalling.
mod, dyn, reinstate
install a dynamic or modified route. These flags are for
diagnostic purposes, and are generally only set by routing
dev If force the route to be associated with the specified device, as
the kernel will otherwise try to determine the device on its own
(by checking already existing routes and device specifications,
and where the route is added to). In most normal networks you
won’t need this.
If dev If is the last option on the command line, the word dev
may be omitted, as it’s the default. Otherwise the order of the
route modifiers (metric - netmask - gw - dev) doesn’t matter.
route add -net 127.0.0.0 netmask 255.0.0.0 dev lo
adds the normal loopback entry, using netmask 255.0.0.0 and
associated with the "lo" device (assuming this device was
previously set up correctly with ifconfig(8)).
route add -net 184.108.40.206 netmask 255.255.255.0 dev eth0
adds a route to the local network 192.56.76.x via "eth0". The
word "dev" can be omitted here.
route del default
deletes the current default route, which is labeled "default" or
0.0.0.0 in the destination field of the current routing table.
route add default gw mango-gw
adds a default route (which will be used if no other route
matches). All packets using this route will be gatewayed
through "mango-gw". The device which will actually be used for
that route depends on how we can reach "mango-gw" - the static
route to "mango-gw" will have to be set up before.
route add ipx4 sl0
Adds the route to the "ipx4" host via the SLIP interface
(assuming that "ipx4" is the SLIP host).
route add -net 220.127.116.11 netmask 255.255.255.0 gw ipx4
This command adds the net "192.57.66.x" to be gatewayed through
the former route to the SLIP interface.
route add -net 18.104.22.168 netmask 240.0.0.0 dev eth0
This is an obscure one documented so people know how to do it.
This sets all of the class D (multicast) IP routes to go via
"eth0". This is the correct normal configuration line with a
route add -net 10.0.0.0 netmask 255.0.0.0 reject
This installs a rejecting route for the private network
The output of the kernel routing table is organized in the following
The destination network or destination host.
The gateway address or ’*’ if none set.
The netmask for the destination net; ’255.255.255.255’ for a
host destination and ’0.0.0.0’ for the default route.
Flags Possible flags include
U (route is up)
H (target is a host)
G (use gateway)
R (reinstate route for dynamic routing)
D (dynamically installed by daemon or redirect)
M (modified from routing daemon or redirect)
A (installed by addrconf)
C (cache entry)
! (reject route)
Metric The ’distance’ to the target (usually counted in hops). It is
not used by recent kernels, but may be needed by routing
Ref Number of references to this route. (Not used in the Linux
Use Count of lookups for the route. Depending on the use of -F and
-C this will be either route cache misses (-F) or hits (-C).
Iface Interface to which packets for this route will be sent.
MSS Default maximum segment size for TCP connections over this
Window Default window size for TCP connections over this route.
irtt Initial RTT (Round Trip Time). The kernel uses this to guess
about the best TCP protocol parameters without waiting on
(possibly slow) answers.
HH (cached only)
The number of ARP entries and cached routes that refer to the
hardware header cache for the cached route. This will be -1 if a
hardware address is not needed for the interface of the cached
route (e.g. lo).
Arp (cached only)
Whether or not the hardware address for the cached route is up
ifconfig(8), netstat(8), arp(8), rarp(8)
Route for Linux was originally written by Fred N. van Kempen,
<email@example.com> and then modified by Johannes Stille and
Linus Torvalds for pl15. Alan Cox added the mss and window options for
Linux 1.1.22. irtt support and merged with netstat from Bernd
Currently maintained by Phil Blundell <Philip.Blundell@pobox.com> and
Bernd Eckenfels <firstname.lastname@example.org>.