Provided by: siggen_2.3.10-1_i386
swgen - a simple swept frequency signal generator
swgen [-2] [-s samples] [-8/-16|-b 8/16] [sweepwaveform]
sweepfreq [sweptwaveform] minfreq maxfreq
swgen [-2] [-s samples] [-8/-16|-b 8/16] [sweepwaveform]
sweepfreq [sweptwaveform] centrefreq percent%
waveform, either sweep or swept,
is sine, cosine, square, triangle, sawtooth, noise
for full list of options see below.
swgen generates a swept frequency waveform on the LINUX /dev/dsp
device. The swept and sweep waveform can be seperately specified, as
can the sweep frequency range and the sweeping frequency. Sweep
frequency range can be specified either by giving the minimum (start)
and maximum (end) frequency in Hertz; or by giving the centre frequency
and the percentage frequency variation below and above. The percentage
is given as an integer value from 0 to 100.
The default sweep waveform is a sawtooth (ramp), and the default swept
waveform is a sine. If the soundcard can do 16 bit samples, swgen will
do 16 bit by default.
8 or 16 bit samples can be generated, in mono or stereo. In stereo, one
channel carries the swept frequency signal, while the second channel
carries the sweeping signal. This can be useful fed to the X input of
an oscilloscope when displaying frequency response curves etc.
The samples can be written in raw or WAV format to files instead of to
the sound device.
The frequency is specified as an integer number of Hertz. Fractional
Hertz frequencies are not supported. Of course, only frequencies less
than half the samplerate (number of samples/sec) can be generated.
The waveforms that can be generated are:
sine A standard sine wave
cosine a sine wave with a 90 degree phase shift
square a standard square wave with a 50% mark space ratio
a ramp waveform with ’infinitely’ fast flyback (:-) An ideal
oscilloscope timebase signal.
shaped like equally spaced teeth on a saw (:-)
noise This is weak. All it consists of is one second of pseudo-
randomly generated samples, played repeatedly. I’d love to do
proper white/pink noise, but I don’t know enough, and I don’t
think the structure of the program is conducive to accurate
swgen creates one second’s worth of generated output in a buffer and
plays the buffer repeatedly, until it is terminated.
A lot of thought has gone into the algorithms for generating the
waveforms. I believe the sin/cos wave to be very pure (modulo your
sound card :-), but I don’t have access to a THD meter to measure it.
For best signal accuracy NEVER use the gain factor option (-A). The
generator will then make the wave’s peak value fit the maximum digital
values allowed. Use a mixer program to control the output volume, or an
The gain factor option can be useful for simulating a signal that has
been subject to clipping. Specify a gain of > 100%. In fact a trapezoid
signal can be made by generating a clipped triangular wave. The greater
the gain, the closer the signal approaches a square wave (the rise and
fall times decrease).
output to /dev/dsp, 22050 samples/sec, mono, 16 bit samples if
possible, else 8 bit.
-h display usage and help info
-v be verbose
-f,-a force overwrite/append of/to file.
use "file" as the local configuration file (see below).
write digital sample to file (’-’ is stdout)
as ’-o’ but written as a WAVE format file. -a (append) is not
valid with this option.
generate with samplerate of samples/sec
-8/-16 or -b 8|16
force 8 bit or 16 bit mode.
-1,-2 mono (def), or special stereo mode (see above).
-A n scale samples by n/100, def. n is 100 (i.e. percentage of full
generate output for either N secs or Nm millisecs only.
-x10 or -x100
Scale frequencies down by a factor of 10 or 100. This allows
fractional Hz values to be generated. See EXAMPLES below for its
use. It is a Kludge.
swgen -v 2 100 1000
sweep a sin wave from 100Hz to 1000Hz using a sawtooth wave
twice a second, at 22050 samples/sec, 16bit samples on 16 bit
card, 8 bit samples on an 8 bit card.
swgen -v -s 44100 -w sweep.wav 2 100 1000
as above but at a samplerate or 44100/sec and save one second of
samples as a WAVE file in sweep.wav
swgen -v -2 squ 10 1000 20%
generate a sine wave switched by a 10Hz squarewave between 800Hz
and 1200Hz. The swept signal is on one channel and the 10Hz
square wave is on the second channel.
swgen -v -x10 5 4400 4500
generate a swept sine wave from 440Hz (4400/10) to 450Hz
(4500/10), being swept at a frequency of 0.5Hz (5/10). Yes it’s
a royal pain remembering to scale all freqs. up by a factor of
10, but I needed it in a hurry and didn’t have time to do it
Three possible configuration files can be used: a LOCAL config file
(usually in current directory), a HOME config file in user’s $HOME
directory and a GLOBAL config file.
All the siggen suite of programs are compiled with the names of the
config files built in. By default the configuration files are:
is the LOCAL config file.
is the HOME config file.
is the GLOBAL config file.
will indicate which config files will be searched for.
The config files do not have to exist. If they exist and are readable
by the program they are used, otherwise they are simply ignored.
The config files are always searched for configuration values in the
order LOCAL, HOME, GLOBAL. This allows a scheme where the sysadmin sets
up default config values in the GLOBAL config file, but allows a user
to set some or all different values in their own HOME config file, and
to set yet more specific values when run from a particular directory.
If no configuration files exist, the program provides builtin default
values, and most of these values can be set by appropriate command line
switches and flags.
See siggen.conf(5) for details of the configuration files.
swgen looks for configuration values CHANNELS, DACFILE, SAMPLERATE,
sets either mono or stereo mode like the ’-1|-2’ options.
allows the name of the DAC/DSP/PCM device to be changed from
sets the number of samples/sec for the DAC device
sets whether 8 or 16 bit samples to be generated
sets whether or not to run in verbose mode.
Copyright 1995-2008 Jim Jackson
The software described by this manual is covered by the GNU General
Public License, Version 2, June 1991, issued by :
Free Software Foundation, Inc.,
675 Mass Ave,
Cambridge, MA 02139, USA
Permission is granted to make and distribute verbatim copies of this
manual provided the copyright notice and this permission notice are
preserved on all copies.
Permission is granted to copy and distribute modified versions of this
manual under the conditions for verbatim copying, provided that the
entire resulting derived work is distributed under the terms of a
permission notice identical to this one.
Permission is granted to copy and distribute translations of this
manual into another language, under the above conditions for modified
versions, except that this permission notice may be included in
translation instead of in the original English.