Provided by: nas_1.9.1-4_i386
nasd.conf - Configuration file for NAS servers.
nasd.conf Is a file that can be used to configure the behaiviour of the
NAS server, including what devices it will attempt to use, the minimum
& maximum frequencies used, if the device should be used in 8bit or
16bit mode, what fragment size and number of fragments should be used
(useful for tuning the server’s latency) and if the server should be
verbose when starting or output debugging information. Not all options
are supported for all servers, see the /etc/nas/nasd.conf.eg file for
information on what options are supported for which servers.
THE CONFIG FILE SYNTAX
There are up to three section in the config file. The first section
deals with global options, some of which just turn on verbose messages
when parsing the config file, and setting debug messages on. The
remaining two sections will, if present, adjust various parameters of
the input and output devices, for those servers that understand them.
verbose Sets a flag telling the server to report what it’s trying to do
with each setting in the config file. This option is off by default.
debug <number> Sets the debug flag, which will provide a trace of the
server’s activities on stderr. Set <number> to 0 to disable debug
messages, 99 for *alot* of debug messages. This option defaults to 0.
ReleaseDevice YES | NO Set to YES or NO. Defines whether the server
should release the audio device when finished playing or recording a
sound. This option defaults to YES. (voxware, hpux, sun)
KeepMixer YES | NO Set to YES or NO. Defines whether the server should
keep the mixer open when releasing the audio device. Without an open
mixer device the server will always report the default gain and line
mode and cannot change them either. This option defaults to YES.
MixerInit YES | NO Set to YES or NO. Defines whether the server will
init the mixer device on startup. Later changes of gain or input mode
will change the mixer settings. This option defaults to NO. (voxware)
ReInitMixer YES | NO Set to YES or NO. Defines whether the server will
re-init the mixer device on every audio device open. The mixer is re-
initialized only if it is initialized at startup (see MixerInit
option). This option defaults to NO. (voxware)
OutDevType EXT | INT For HPUX servers, define to EXT to use the
external output device (headphone/speakers) or INT for the internal
output device (internal speaker). Defaults to EXT.
outputsection Marks the beginning of the output section, which allows
various parameters of the output device to be set up.
inputsection Marks the beginning of the input section, which allows
various parameters of the input device to be set up.
end Marks the end of the input section or output section.
device <devname> Specifies what device is used. An example is device
"/dev/dsp". With the voxware server you can use the empty string "" to
disable the device.
mixer <mixername> Specifies what mixer device is used. An example is
mixer "/dev/mixer". If <mixername> is set to the empty string "" no
mixer is used in this section.
gain <number> Specifies the default volume (0-100). The default is 50.
gainscale <number> This factor (expressed as a percentage) is applied
to all volume-setting requests. This lets the server transparently
limit the actual maximum volume that can be set by clients. The default
maxrate <number> The maximum number of samples per second that we’ll
drive the card at.
minrate <number> The minimum number of samples per second that the card
will be driven at.
maxfrags <number> The maximum number of of kernel buffers that will be
used for the device. the number is dynamically adjusted as the
sampling frequency varies.
minfrags <number> The minimum number of kernel buffers that will be
fragsize <number> The size of each buffer - note that the size must be
a power of 2.
wordsize <number> The number of bits per sample. Allowable values are 8
numchans <number> Used to decide if the card is run in stereo or mono
mode. Allowable values are 1 or 2.
forcerate no | yes Forces the output rate to the current rate. The
default is no.
autoOpen no | yes Whether to open the device at init time (if
ReleaseDevice = no). The default is yes.
readwrite no | yes Whether or not to open the device read-write. The
default is no. If set to yes, then the device will be opened
read-write. There should be no need to set this to yes, but...
nas(1), nasd(1), auinfo(1), auplay(1), auctl(1)
Stephen Hocking (firstname.lastname@example.org), Jon Trulson