Provided by: geographiclib-tools_1.52-1_amd64 bug

NAME

       Planimeter -- compute the area of geodesic polygons

SYNOPSIS

       Planimeter [ -r ] [ -s ] [ -l ] [ -e a f ] [ -w ] [ -p prec ] [ -G | -E | -Q | -R ] [
       --comment-delimiter commentdelim ] [ --version | -h | --help ] [ --input-file infile |
       --input-string instring ] [ --line-separator linesep ] [ --output-file outfile ]

DESCRIPTION

       Measure the area of a geodesic polygon.  Reads polygon vertices from standard input, one
       per line.  Vertices may be given as latitude and longitude, UTM/UPS, or MGRS coordinates,
       interpreted in the same way as GeoConvert(1).  (MGRS coordinates signify the center of the
       corresponding MGRS square.)  The end of input, a blank line, or a line which can't be
       interpreted as a vertex signals the end of one polygon and the start of the next.  For
       each polygon print a summary line with the number of points, the perimeter (in meters),
       and the area (in meters^2).

       The edges of the polygon are given by the shortest geodesic between consecutive vertices.
       In certain cases, there may be two or many such shortest geodesics, and in that case, the
       polygon is not uniquely specified by its vertices.  This only happens with very long edges
       (for the WGS84 ellipsoid, any edge shorter than 19970 km is uniquely specified by its end
       points).  In such cases, insert an additional vertex near the middle of the long edge to
       define the boundary of the polygon.

       By default, polygons traversed in a counter-clockwise direction return a positive area and
       those traversed in a clockwise direction return a negative area.  This sign convention is
       reversed if the -r option is given.

       Of course, encircling an area in the clockwise direction is equivalent to encircling the
       rest of the ellipsoid in the counter-clockwise direction.  The default interpretation used
       by Planimeter is the one that results in a smaller magnitude of area; i.e., the magnitude
       of the area is less than or equal to one half the total area of the ellipsoid.  If the -s
       option is given, then the interpretation used is the one that results in a positive area;
       i.e., the area is positive and less than the total area of the ellipsoid.

       Arbitrarily complex polygons are allowed.  In the case of self-intersecting polygons the
       area is accumulated "algebraically", e.g., the areas of the 2 loops in a figure-8 polygon
       will partially cancel.  Polygons may include one or both poles.  There is no need to close
       the polygon.

OPTIONS

       -r  toggle whether counter-clockwise traversal of the polygon returns a positive (the
           default) or negative result.

       -s  toggle whether to return a signed result (the default) or not.

       -l  toggle whether the vertices represent a polygon (the default) or a polyline.  For a
           polyline, the number of points and the length of the path joining them is returned;
           the path is not closed and the area is not reported.

       -e a f
           specify the ellipsoid via the equatorial radius, a and the flattening, f.  Setting f =
           0 results in a sphere.  Specify f < 0 for a prolate ellipsoid.  A simple fraction,
           e.g., 1/297, is allowed for f.  By default, the WGS84 ellipsoid is used, a = 6378137
           m, f = 1/298.257223563.  If entering vertices as UTM/UPS or MGRS coordinates, use the
           default ellipsoid, since the conversion of these coordinates to latitude and longitude
           always uses the WGS84 parameters.

       -w  toggle the longitude first flag (it starts off); if the flag is on, then when reading
           geographic coordinates, longitude precedes latitude (this can be overridden by a
           hemisphere designator, N, S, E, W).

       -p prec
           set the output precision to prec (default 6); the perimeter is given (in meters) with
           prec digits after the decimal point; the area is given (in meters^2) with (prec - 5)
           digits after the decimal point.

       -G  use the series formulation for the geodesics.  This is the default option and is
           recommended for terrestrial applications.  This option, -G, and the following three
           options, -E, -Q, and -R, are mutually exclusive.

       -E  use "exact" algorithms (based on elliptic integrals) for the geodesic calculations.
           These are more accurate than the (default) series expansions for |f| > 0.02.  (But
           note that the implementation of areas in GeodesicExact uses a high order series and
           this is only accurate for modest flattenings.)

       -Q  perform the calculation on the authalic sphere.  The area calculation is accurate even
           if the flattening is large, provided the edges are sufficiently short.  The perimeter
           calculation is not accurate.

       -R  The lines joining the vertices are rhumb lines instead of geodesics.

       --comment-delimiter commentdelim
           set the comment delimiter to commentdelim (e.g., "#" or "//").  If set, the input
           lines will be scanned for this delimiter and, if found, the delimiter and the rest of
           the line will be removed prior to processing.  For a given polygon, the last such
           string found will be appended to the output line (separated by a space).

       --version
           print version and exit.

       -h  print usage and exit.

       --help
           print full documentation and exit.

       --input-file infile
           read input from the file infile instead of from standard input; a file name of "-"
           stands for standard input.

       --input-string instring
           read input from the string instring instead of from standard input.  All occurrences
           of the line separator character (default is a semicolon) in instring are converted to
           newlines before the reading begins.

       --line-separator linesep
           set the line separator character to linesep.  By default this is a semicolon.

       --output-file outfile
           write output to the file outfile instead of to standard output; a file name of "-"
           stands for standard output.

EXAMPLES

       Example (the area of the 100km MGRS square 18SWK)

          Planimeter <<EOF
          18n 500000 4400000
          18n 600000 4400000
          18n 600000 4500000
          18n 500000 4500000
          EOF
          => 4 400139.53295860 10007388597.1913

       The following code takes the output from gdalinfo and reports the area covered by the data
       (assuming the edges of the image are geodesics).

          #! /bin/sh
          egrep '^((Upper|Lower) (Left|Right)|Center) ' |
          sed -e 's/d /d/g' -e "s/' /'/g" | tr -s '(),\r\t' ' ' | awk '{
              if ($1 $2 == "UpperLeft")
                  ul = $6 " " $5;
              else if ($1 $2 == "LowerLeft")
                  ll = $6 " " $5;
              else if ($1 $2 == "UpperRight")
                  ur = $6 " " $5;
              else if ($1 $2 == "LowerRight")
                  lr = $6 " " $5;
              else if ($1 == "Center") {
                  printf "%s\n%s\n%s\n%s\n\n", ul, ll, lr, ur;
                  ul = ll = ur = lr = "";
              }
          }
          ' | Planimeter | cut -f3 -d' '

ACCURACY

       Using the -G option (the default), the accuracy was estimated by computing the error in
       the area for 10^7 approximately regular polygons on the WGS84 ellipsoid.  The centers and
       the orientations of the polygons were uniformly distributed, the number of vertices was
       log-uniformly distributed in [3, 300], and the center to vertex distance log-uniformly
       distributed in [0.1 m, 9000 km].

       The maximum error in the perimeter was 200 nm, and the maximum error in the area was

          0.0013 m^2 for perimeter < 10 km
          0.0070 m^2 for perimeter < 100 km
          0.070 m^2 for perimeter < 1000 km
          0.11 m^2 for all perimeters

SEE ALSO

       GeoConvert(1), GeodSolve(1).

       An online version of this utility is availbable at
       <https://geographiclib.sourceforge.io/cgi-bin/Planimeter>.

       The algorithm for the area of geodesic polygon is given in Section 6 of C. F. F. Karney,
       Algorithms for geodesics, J. Geodesy 87, 43-55 (2013); DOI
       <https://doi.org/10.1007/s00190-012-0578-z>; addenda:
       <https://geographiclib.sourceforge.io/geod-addenda.html>.

AUTHOR

       Planimeter was written by Charles Karney.

HISTORY

       Planimeter was added to GeographicLib, <https://geographiclib.sourceforge.io>, in version
       1.4.