Provided by: survex_1.0.39.1-2.1_i386 bug

NAME

       printhpgl  —  print .3d files on a plotter supporting Hewlett Packard’s
       HPGL

SYNOPSIS

       printhpgl [options] .3d file ...

Description

       Printhpgl produces output suitable for plotters  that  support  Hewlett
       Packard’s HPGL.

       The  configuration file print.ini, which sets various features for each
       printer. See the ’Printer Settings’ section for details. Even  if  your
       printer  is  not  standard  you  should  be  able  get  it  to  work by
       customising one of the supplied definitions.

Options

       The command line options are:

       --survey=SURVEY
                 Only load the sub-survey SURVEY

       -e, --elevation
                 select elevation

       -p, --plan
                 select plan view

       -b, --bearing=BEARING
                 set bearing

       -t, --tilt=TILT
                 set tilt

       -s, --scale=SCALE
                 set scale

       -n, --station-names
                 display station names

       -c, --crosses
                 display crosses at stations

       -B, --no-border
                 turn off the solid border around  the  edge  of  the  survey.
                 Printing   to   dot-matrix   and   inkjet   printers  can  be
                 significantly faster without this  border  as  the  printhead
                 usually  doesn’t  need to move all the way to the edge of the
                 paper.

       -C, --no-cutlines
                 If a printout takes more than one page, alignment  ticks  are
                 printed where the page corners need to be joined.  By default
                 dash lines are also drawn along internal edges to  facilitate
                 trimming  down  the  page  with  scissors.   If  you  have  a
                 guillotine, the alignment ticks are sufficient  for  trimming
                 the  page  and  this option allows you to turn off the dashed
                 lines.

       -l, --no-legs
                 turn off display of survey legs

       -S, --surface
                 turn on display of  surface  survey  legs.  By  default  only
                 underground survey legs are shown.

       -k, --skip-blanks
                 don’t  output  blank  pages  With this option pages which are
                 blank (apart from alignment marks and borders)  will  not  be
                 printed.

       -o, --output=OUTPUT
                 set output file

Interactive Use

       When you run the printer driver you will be asked if you want a plan or
       elevation (enter <P>, or <E>) - the default is plan. Then enter  values
       for  the  desired plot view. These values correspond to those displayed
       in the bottom right hand corner when using Aven (or the top right  when
       using caverot).  You would usually use Aven or caverot to pick the best
       view and then note the angles before running the Printer  Driver.  This
       will be integrated soon.

       For a plan enter bearing up the page, in degrees, 0 indicating North at
       the top of the page (the default).

       For an elevation enter the angle of view (i.e. the compass bearing from
       which the scene is viewed), and angle of tilt, where 0 is horizontal, -
       is looking down from above, and + is looking up from below, so  -90  is
       the same as plan view.

       For an extended elevation, no viewing angles are needed.

       You’ll  be  told  the  scale needed to fit the plot on one page, and be
       asked what scale you want to use. The you’re told how many  pages  this
       will  take (and the arrangement of those pages (e.g. 6 pages (2x3)) and
       have the opportunity to print, quit, or change the scale  (so  you  can
       repeat  this process until you have a scale and number of pages you are
       happy with).

       You can then print all the pages, a range of pages,  or  any  arbitrary
       list  of pages and ranges (handy for when your printer mangles a page).

See Also

       3dtopos(1),  aven(1),  cad3d(1),  cavern(1),   diffpos(1),   extend(1),
       printdm(1),    printpcl(1),    printps(1),    sorterr(1),   svxedit(1),
       xcaverot(1), print.ini(5)

                                                                  printhpgl(1)