Provided by: freebsd-manpages_7.1~beta1-1_all
nfe - NVIDIA nForce MCP Ethernet driver
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
The nfe driver supports PCI Ethernet adapters based on the NVIDIA nForce
Media and Communications Processors (MCP), such as the nForce, nForce 2,
nForce 3, CK804, MCP04, MCP51, MCP55, MCP61, MCP65, MCP67 and MCP73
Ethernet controller chips.
Supported features include (hardware support provided):
· Receive/Transmit IP/TCP/UDP checksum offload
· Hardware VLAN tag insertion/stripping
· TCP segmentation offload (TSO)
· Jumbo Frames
Support for Jumbo Frames is provided via the interface MTU setting.
Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames.
The nfe driver supports the following media types:
autoselect Enable autoselection of the media type and options.
10baseT/UTP Set 10Mbps operation.
100baseTX Set 100Mbps (Fast Ethernet) operation.
1000baseT Set 1000Mbps (Gigabit Ethernet) operation (recent models
The nfe driver supports the following media options:
half-duplex Force half duplex operation.
full-duplex Force full duplex operation.
For more information on configuring this device, see ifconfig(8).
The nfe driver supports the following NVIDIA MCP onboard adapters:
· NVIDIA nForce MCP Networking Adapter
· NVIDIA nForce MCP04 Networking Adapter
· NVIDIA nForce 430 MCP12 Networking Adapter
· NVIDIA nForce 430 MCP13 Networking Adapter
· NVIDIA nForce MCP51 Networking Adapter
· NVIDIA nForce MCP55 Networking Adapter
· NVIDIA nForce MCP61 Networking Adapter
· NVIDIA nForce MCP65 Networking Adapter
· NVIDIA nForce MCP67 Networking Adapter
· NVIDIA nForce MCP73 Networking Adapter
· NVIDIA nForce2 MCP2 Networking Adapter
· NVIDIA nForce2 400 MCP4 Networking Adapter
· NVIDIA nForce2 400 MCP5 Networking Adapter
· NVIDIA nForce3 MCP3 Networking Adapter
· NVIDIA nForce3 250 MCP6 Networking Adapter
· NVIDIA nForce3 MCP7 Networking Adapter
· NVIDIA nForce4 CK804 MCP8 Networking Adapter
· NVIDIA nForce4 CK804 MCP9 Networking Adapter
Tunables can be set at the loader(8) prompt before booting the kernel or
stored in loader.conf(5).
Whether or not MSI support is enabled in the driver. The default
value is 0.
Whether or not MSI-X support is enabled in the driver. The
default value is 0.
The following sysctl(8) variables can be used to modify or monitor nfe
Maximum number of Rx events to be processed in the event loop
before rescheduling a taskqueue. The accepted range is 50 to
255, the default value is 192. The interface does not need to be
brought down and up again before a change takes effect.
altq(4), arp(4), intro(4), miibus(4), netintro(4), pci(4), polling(4),
The nfe device driver first appeared in OpenBSD 3.9, and then in
The nfe driver was written by Jonathan Gray 〈firstname.lastname@example.org〉 and Damien
Bergamini 〈email@example.com〉. The nfe driver was ported to FreeBSD by
Shigeaki Tagashira 〈firstname.lastname@example.org〉.