Provided by: srecord_1.39-1_i386
srec_signetics - Signetics file format
The Signetics file format is not often used. The major disadvantage in
modern applications is that the addressing range is limited to only
All data lines are called records, and each record contains the
following 5 fields:
|: | aaaa | cc | as | dd | ss |
The field are defined-as-follows:--+----+----+----+
: Every record starts with this identifier.
aaaa The address field. A four digit (2 byte) number representing
the first address to be used by this record.
cc The byte-count. A two digit value (1 byte), counting the
actual data bytes in the record.
as Address checksum. Covers 2 address bytes and the byte count.
dd The actual data of this record. There can be 1 to 255 data
bytes per record (see cc)
ss Data Checksum. Covers only all the data bytes of this record.
Every record begins with a colon ‘‘:’’ character. Records contain only
ASCII characters. No spaces or tabs are allowed in a record. In fact,
apart from the 1st colon, no other characters than 0..9 and A..F are
allowed in a record. Interpretation of a record should be case less,
it does not matter if you use a..f or A..F.
Unfortunately the colon was chosen for the Signetics file format,
similar to the Intel format (see srec_intel(5) for more information).
However, SRecord is able to automatically detect the dofference between
the two format, when you use the -Guess format specifier.
This is the address where the first data byte of the record should be
stored. After storing that data byte, the address is incremented by 1
to point to the address for the next data byte of the record. And so
on, until all data bytes are stored. The address is represented by a 4
digit hex number (2 bytes), with the MSD first. The order of addresses
in the records of a file is not important. The file may also contain
address gaps, to skip a portion of unused memory.
The byte count cc counts the actual data bytes in the current record.
Usually records have 32 data bytes, but any number between 1 and 255 is
A value of 0x00 for cc indicates the end of the file. In this case not
even the address checksum will follow! The record (and file) are
It is not recommended to send too many data bytes in a record for that
may increase the transmission time in case of errors. Also avoid
sending only a few data bytes per record, because the address overhead
will be too heavy in comparison to the payload.
This is not really a checksum anymore, it looks more like a CRC. The
checksum can not only detect errors in the values of the bytes, but
also bytes out of order can be detected.
The checksum is calculated by this algorithm:
checksum = 0
for i = 1 to 3
checksum = checkum XOR byte
For the Address Checksum we only need 2 Address bytes and 1 Byte Count
byte to be added. That’s why we count to 3 in the loop. Every byte is
XORed with the previous result. Then the intermediate result is rolled
left (carry rolls back into b0).
This results in a very reliable checksum, and that for only 3 bytes!
The last record of the file does not contain any checksums! So the
file ends right after the Byte Count of 0.
The payload of the record is formed by the Data field. The number of
data bytes expected is given by the Byte Count field. The last record
of the file may not contain a Data field.
This checksum uses the same algorithm as used for the Address Checksum.
This time we calculate the checksum with only the data bytes of this
checksum = 0
for i = 1 to cc
checksum = checksum XOR byte
Note that we count to the Byte Count cc this time.
In general, binary data will expand in sized by approximately 2.4 times
when represented with this format.
Here is an example Signetics file
In the example above you can see a piece of code in Signetics format.
The first 3 lines have 16 bytes of data each, which can be seen by the
byte count. The 4th line has only 13 bytes, because the program is at
it’s end there.
Notice that the last record of the file contains no data bytes, and not
even an Address Checksum.
This man page was taken from the above Web page. It was written by San