Provided by: hylafax-server_4.4.4-10.1ubuntu2_i386
faxmodem - dynamically add a modem to a HylaFAX server system
/usr/sbin/faxmodem [ -q queue-dir ] [ -c capabilities ] [ -p ] [ -P ] [
-u priority ] modem
faxmodem sends a message to the HylaFAX queuer process faxq(8) telling
it that the specified modem is ready for use and informing it about its
fax-related capabilities. This is the mechanism by which modems are
added in a send-only configuration. Once a modem has been configured
its status can be reconfigured using the faxstate(8) program. faxmodem
can also be used to alter the capabilities and usage priority of a
previously configured modem.
The specified modem is either the terminal device name where the modem
is attached or a HylaFAX device identifier (see hylafax-config(5) for
information on device identifiers). Device names may be given without
a leading directory pathname; e.g. ttyf2 instead of /dev/ttyf2.
To figure out the capabilities of a modem either use the probemodem(8)
script or manually communicate with the modem. For a Class 2 modem the
capabilities are given in the response to the ‘‘AT+FDCC=?’’ query
command and for a Class 2.0 modem the ‘‘AT+FCC=?’’ command. To check
if a modem is capable of polled retrieval of documents use ‘‘AT+FSP=?’’
for a Class 2.0 modem or ‘‘AT+FSPL=?’’ for a Class 2 modem; if ‘‘1’’ is
indicated in the response then the modem supports polling. For
hyla% cu -l ttyf2
In this case the modem would be added using the command:
/usr/sbin/faxmodem -c ’(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)’ ttyf2
(by default polling is assumed to be supported).
Class 1 modems require a different technique. The host implements most
of the fax protocol so all that is needed is to identify the possible
signalling rates the modem supports for transmitting; this is done with
the ‘‘AT+FTM=?’’ command. For example,
hyla% cu -l ttyf2
In this case the modem supports 2400, 4800, 7200, 9600, 12200, and
14400 bps signalling rates so the modem would be added using:
/usr/sbin/faxmodem -c ’(0,1),(0-5),(0-2),(0-2),(0,1),0,0,(0-7)’ ttyf2
The following options are available:
-c Specify the fax capabilities using the syntax defined by the
‘‘Class 2’’ specification:
‘‘(vr),(br),(wd),(ln),(df),(ec),(bf),(st)’’. where, vr
specifies vertical resolution, br specifies bit rate, wd
specifies page width, ln specifies page length, df specifies
data compression, ec specifies error correction, bf specifies
binary file transfer, and st specifies scan time/line; and
each of the above specifications is a range or list of
numbers that defines the exact capabilities of the modem.
For example, the default capabilities are
‘‘(0,1),(0-3),(0-4),(0-2),(0),(0),(0),(0-7)’’ which specifies
the modem is capable of sending and receiving both low and
high resolution facsimile with a variety of page sizes;
supports signalling rates 0-3 (2400 bps through 9600 bps);
supports only 1D-encoded data compression; and does not
support error correction or binary file transfer. A modem’s
ability to support polled retrieval of facsimile is specified
separately with the -p and -P options.
-p Specify the modem is not capable of polling for remote
-P Specify the modem is capable of polling for remote documents
-q dir Use a spooling area other than /var/spool/hylafax.
Assign the specified priority to the modem when scheduling it
for outbound use. Modem priorities are numbers in the range
[0..255] with lower numbers meaning higher priority. Modems
are initially assigned priority 255.
/var/spool/hylafax default spooling area
/var/spool/hylafax/FIFO fifo for contacting faxq
Consult hylafax-server(5) for a complete discussion of the structure
and content of the spooling area.
hylafax-server(5), faxgetty(8), faxq(8).
Oct 27, 1995 FAXMODEM(8)