Provided by: bridge-utils_1.4-5ubuntu2_i386
bridge-utils-interfaces - bridge-utils extensions for the interfaces(5)
/etc/network/interfaces contains network interface configuration
information for the ifup(8) and ifdown(8) commands. This manpage
describes the bridge extensions to the standard interfaces(5) file
The main extension is the bridge_ports option, with it you describe
that the interface is a bridge and what ports does it have. These ports
are the interfaces that are part of the bridge, and they shouldn’t have
any stanzas defining them on the interfaces file. Other extensions
allow you to tune the bridge options or change a bridge behaviour.
We’ll see this with an example:
iface br0 inet static
Well, after setting this, an ifup br0, or the next reboot, should let
you have a bridge up and running, after waiting for the ports to get to
the forwarding status, of course. This bridge will be using all your
ethX interfaces, as we have stated on the bridge_ports line.
The Debian bridge setup scripts will wait for it to get ready to work.
They do this by trying to guess the maximum time that the bridge will
need to get to the forwarding status, and by default, they will wait
for the bridge to get there, or for the estimated maximum time to go
by. This is done so that the services that are loaded after the bridge
setup have a working network interface and don’t fail because the
bridge is still not working. See bridge_maxwait if you want to change
An example of how to setup a so called anonymous bridge (a bridge
without an assigned IP) would look like this:
iface br1 inet manual
bridge_ports eth1 eth2
Here we select the interfaces eth1 and eth2 to be added to the bridge
interface br1, which will be an anonymous bridge, we also tell the
scripts not to wait, as we won’t be having any service running on that
interface (it doesn’t even have an IP).
An example of a little more complex bridge setup could be:
iface br0 inet static
bridge_ports all weird0
bridge_portprio eth0 129
In this example we select all the eth* devices plus a weird device to
be added to the bridge, also we change the bridge default priority to a
higher one so that this bridge becomes the root (if there are no
bridges with higher priority on the net, that is) and also we lower
priority of port eth0 so that it is not used if there are other ports
with higher priority to reach the same destination, at the end we lower
the default forward delay.
If there is a need to set up any of the interfaces participating on the
bridge and not the bridge itself, then we must add the commands to set
up those settings in a "pre-up" or "up" statement. This means that if
we have a wireless card that we want to add to a bridge and we want to
set it to master, and select the essid, instead of using the typical
wireless_* commands we could add to the bridge definition something
pre-up iwconfig wlan0 mode master essid myESSID
Be aware, however, that using wireless cards as part of a bridge is not
a good idea if the card belonging to the bridge is in managed mode.
Trying to bridge packets coming out of our LAN through a wireless card
that is set in managed mode (the card is a client of an AP) is bound to
give problems, as the AP will probably refuse packets with source MAC
addresses which are not associated (this will be the case of other
machines going through the wireless card of the bridge into the AP).
Multiple stanzas of a bridge definition are currently not supported, so
if you want to add a ipv6 and a ipv4 to a bridge do it all in one
definition by using the "up" option. If however you still want to use
multiple stanzas or would like to read more on this bug you can see it
A little explanation on the new options that can be used on
/etc/network/interfaces to setup the bridge, so you don’t have to go
and look at the scripts...
bridge_ports interface specification
this option must exist for the scripts to setup the bridge, with
it you specify the ports you want to add to your bridge, either
using "none" if you want a bridge without any interfaces or you
want to add them later using brctl, or a list of the interfaces
you want to add separated by spaces, for example:
bridge_ports eth0 eth4
You should not put any lines to configure the interfaces that
will be used by the bridge, as this will be setup automatically
by the scripts when bringing the bridge up.
If you need to specify the interfaces more flexibly, you can use
the following syntax (most useful on a Xen dom0):
bridge_ports regex (eth|vif).*
This means to evaluate (as in egrep(1)) the expressions that
follow after "regex" until either the end or a "noregex"
statement is reached. The regular expressions are evaluated
against all local interfaces and those that match are added.
Specifying "all" is short for "regex eth.* noregex" and will get
all the ethX interfaces added to the bridge.
Carrying this to the extremes, the following is valid syntax:
bridge_ports all regex if.0 noregex ext0 regex vif.*
This will add all ethX interfaces, the ifX0 interfaces, the ext0
interface and all vifX interfaces.
set ageing time, default is 300, can have a fractional part.
set bridge priority, priority is between 0 and 65535, default is
32768, affects bridge id, lowest priority bridge will be the
set bridge forward delay to time seconds, default is 15, can
have a fractional part.
set garbage collection interval to time seconds, default is 4,
can have a fractional part.
set hello time to time seconds, default is 2, can have a
bridge_hw MAC address
set the Ethernet MAC address of all the bridge interfaces to the
specified one so that the bridge ends up having this hardware
address as well. WARNING: use this only if you know what you are
doing, changing the MAC address of the cards may cause trouble
if you don’t know what you are doing. To see the discussion
about this feature and the problems that can cause you can try
to have a look at the bug that asked for this feature visiting
set max message age to time seconds, default is 20, can have a
forces to time seconds the maximum time that the Debian bridge
setup scripts will wait for the bridge ports to get to the
forwarding status, doesn’t allow factional part. If it is equal
to 0 then no waiting is done.
bridge_pathcost port cost
set path cost for a port, default is 100, port is the name of
the interface to which this setting applies.
bridge_portprio port priority
set port priority, default is 128, affects port id, port is the
name of the interface to which this setting applies.
turn spanning tree protocol on/off, state values are on or yes
to turn stp on and any other thing to set it off, default has
changed to off for security reasons in latest kernels, so you
should specify if you want stp on or off with this option, and
not rely on your kernel’s default behaviour.
bridge_waitport time [ports]
wait for a max of time seconds for the specified ports to become
available, if no ports are specified then those specified on
bridge_ports will be used here. Specifying no ports here should
not be used if we are using regex or "all" on bridge_ports, as
it wouldn’t work.
definitions of network interfaces See interfaces(5) for more
The default values shown here are current values as of this
writing, but as they are not related to this package but to the
bridge code itself, can change anytime.
This manpage was written by Santiago Garcia Mantinan <firstname.lastname@example.org>
based on interfaces(5).
brctl(8), interfaces(5), ifup(8), iwconfig(8), run-parts(8).