Provided by: uucp_1.07-20build1_i386
uucico - UUCP file transfer daemon
uucico [ options ]
The uucico daemon processes file transfer requests queued by uucp (1)
and uux (1). It is started when uucp or uux is run (unless they are
given the -r option). It is also typically started periodically using
entries in the crontab table(s).
When invoked with -r1, --master, -s, --system, or -S, the daemon will
place a call to a remote system, running in master mode. Otherwise the
daemon will start in slave mode, accepting a call from a remote system.
Typically a special login name will be set up for UUCP which
automatically invokes uucico when a call is made.
When uucico terminates, it invokes the uuxqt (8) daemon, unless the -q
or --nouuxqt option is given; uuxqt (8) executes any work orders
created by uux (1) on a remote system, and any work orders created
locally which have received remote files for which they were waiting.
If a call fails, uucico will normally refuse to retry the call until a
certain (configurable) amount of time has passed. This may be
overriden by the -f, --force, or -S option.
The -l, --prompt, -e, or --loop options may be used to force uucico to
produce its own prompts of "login: " and "Password:". When another
daemon calls in, it will see these prompts and log in as usual. The
login name and password will normally be checked against a separate
list kept specially for uucico rather than the /etc/passwd file; it is
possible on some systems to direct uucico to use the /etc/passwd file.
The -l or --prompt option will prompt once and then exit; in this mode
the UUCP administrator or the superuser may use the -u or --login
option to force a login name, in which case uucico will not prompt for
one. The -e or --loop option will prompt again after the first session
is over; in this mode uucico will permanently control a port.
If uucico receives a SIGQUIT, SIGTERM or SIGPIPE signal, it will
cleanly abort any current conversation with a remote system and exit.
If it receives a SIGHUP signal it will abort any current conversation,
but will continue to place calls to (if invoked with -r1 or --master)
and accept calls from (if invoked with -e or --loop) other systems. If
it receives a SIGINT signal it will finish the current conversation,
but will not place or accept any more calls.
The following options may be given to uucico.
Start in master mode (call out to a system); implied by -s,
--system, or -S. If no system is specified, call any system for
which work is waiting to be done.
Start in slave mode. This is the default.
-s system, --system system
Call the named system.
Call the named system, ignoring any required wait. This is
equivalent to -s system -f.
Ignore any required wait for any systems to be called.
Prompt for login name and password using "login: " and
"Password:". This allows uucico to be easily run from inetd (8).
The login name and password are checked against the UUCP password
file, which probably has no connection to the file /etc/passwd.
The --login option may be used to force a login name, in which
cause uucico will only prompt for a password.
-p port, --port port
Specify a port to call out on or to listen to.
Enter endless loop of login/password prompts and slave mode daemon
execution. The program will not stop by itself; you must use kill
(1) to shut it down.
After calling out (to a particular system when -s, --system, or -S
is specifed, or to all systems which have work when just -r1 or
--master is specifed), begin an endless loop as with --loop.
Do not start the uuxqt (8) daemon when finished.
If no calls are permitted at this time, then don’t make the call,
but also do not put an error message in the log file and do not
update the system status (as reported by uustat (1)). This can be
convenient for automated polling scripts, which may want to simply
attempt to call every system rather than worry about which
particular systems may be called at the moment. This option also
suppresses the log message indicating that there is no work to be
Only call the system named by -s, --system or -S if there is work
for that system.
Do not detach from the controlling terminal. Normally uucico
detaches from the terminal before each call out to another system
and before invoking uuxqt. This option prevents this.
-u name, --login name
Set the login name to use instead of that of the invoking user.
This option may only be used by the UUCP administrator or the
superuser. If used with --prompt, this will cause uucico to
prompt only for the password, not the login name.
If a call fails after the remote system is reached, try the next
alternate rather than simply exiting.
-i type, --stdin type
Set the type of port to use when using standard input. The only
support port type is TLI, and this is only available on machines
which support the TLI networking interface. Specifying -iTLI
causes uucico to use TLI calls to perform I/O.
-x type, -X type, --debug type
Turn on particular debugging types. The following types are
recognized: abnormal, chat, handshake, uucp-proto, proto, port,
config, spooldir, execute, incoming, outgoing.
Multiple types may be given, separated by commas, and the --debug
option may appear multiple times. A number may also be given,
which will turn on that many types from the foregoing list; for
example, --debug 2 is equivalent to --debug abnormal,chat.
The debugging output is sent to the debugging file, which may be
printed using uulog -D.
-I file, --config file
Set configuration file to use. This option may not be available,
depending upon how uucico was compiled.
Report version information and exit.
Print a help message and exit.
kill(1), uucp(1), uux(1), uustat(1), uuxqt(8)
Ian Lance Taylor <email@example.com>
Taylor UUCP 1.07 uucico(8)