Provided by: manpages-dev_3.27-1ubuntu2_all
write - write to a file descriptor
ssize_t write(int fd, const void *buf, size_t count);
write() writes up to count bytes from the buffer pointed buf to the
file referred to by the file descriptor fd.
The number of bytes written may be less than count if, for example,
there is insufficient space on the underlying physical medium, or the
RLIMIT_FSIZE resource limit is encountered (see setrlimit(2)), or the
call was interrupted by a signal handler after having written less than
count bytes. (See also pipe(7).)
For a seekable file (i.e., one to which lseek(2) may be applied, for
example, a regular file) writing takes place at the current file
offset, and the file offset is incremented by the number of bytes
actually written. If the file was open(2)ed with O_APPEND, the file
offset is first set to the end of the file before writing. The
adjustment of the file offset and the write operation are performed as
an atomic step.
POSIX requires that a read(2) which can be proved to occur after a
write() has returned returns the new data. Note that not all file
systems are POSIX conforming.
On success, the number of bytes written is returned (zero indicates
nothing was written). On error, -1 is returned, and errno is set
If count is zero and fd refers to a regular file, then write() may
return a failure status if one of the errors below is detected. If no
errors are detected, 0 will be returned without causing any other
effect. If count is zero and fd refers to a file other than a regular
file, the results are not specified.
EAGAIN The file descriptor fd refers to a file other than a socket and
has been marked nonblocking (O_NONBLOCK), and the write would
EAGAIN or EWOULDBLOCK
The file descriptor fd refers to a socket and has been marked
nonblocking (O_NONBLOCK), and the write would block.
POSIX.1-2001 allows either error to be returned for this case,
and does not require these constants to have the same value, so
a portable application should check for both possibilities.
EBADF fd is not a valid file descriptor or is not open for writing.
fd refers to a datagram socket for which a peer address has not
been set using connect(2).
EFAULT buf is outside your accessible address space.
EFBIG An attempt was made to write a file that exceeds the
implementation-defined maximum file size or the process's file
size limit, or to write at a position past the maximum allowed
EINTR The call was interrupted by a signal before any data was
written; see signal(7).
EINVAL fd is attached to an object which is unsuitable for writing; or
the file was opened with the O_DIRECT flag, and either the
address specified in buf, the value specified in count, or the
current file offset is not suitably aligned.
EIO A low-level I/O error occurred while modifying the inode.
ENOSPC The device containing the file referred to by fd has no room for
EPIPE fd is connected to a pipe or socket whose reading end is closed.
When this happens the writing process will also receive a
SIGPIPE signal. (Thus, the write return value is seen only if
the program catches, blocks or ignores this signal.)
Other errors may occur, depending on the object connected to fd.
SVr4, 4.3BSD, POSIX.1-2001.
Under SVr4 a write may be interrupted and return EINTR at any point,
not just before any data is written.
A successful return from write() does not make any guarantee that data
has been committed to disk. In fact, on some buggy implementations, it
does not even guarantee that space has successfully been reserved for
the data. The only way to be sure is to call fsync(2) after you are
done writing all your data.
If a write() is interrupted by a signal handler before any bytes are
written, then the call fails with the error EINTR; if it is interrupted
after at least one byte has been written, the call succeeds, and
returns the number of bytes written.
close(2), fcntl(2), fsync(2), ioctl(2), lseek(2), open(2), pwrite(2),
read(2), select(2), writev(2), fwrite(3)
This page is part of release 3.27 of the Linux man-pages project. A
description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.