Provided by: avr-libc_1.7.1-2_all bug

NAME

       FAQ - Frequently Asked Questions

FAQ Index

       1.  My program doesn't recognize a variable updated within an interrupt routine

       2.  I get 'undefined reference to...' for functions like 'sin()'

       3.  How to permanently bind a variable to a register?

       4.  How to modify MCUCR or WDTCR early?

       5.  What is all this _BV() stuff about?

       6.  Can I use C++ on the AVR?

       7.  Shouldn't I initialize all my variables?

       8.  Why do some 16-bit timer registers sometimes get trashed?

       9.  How do I use a #define'd constant in an asm statement?

       10. Why does the PC randomly jump around when single-stepping through my program in avr-
           gdb?

       11. How do I trace an assembler file in avr-gdb?

       12. How do I pass an IO port as a parameter to a function?

       13. What registers are used by the C compiler?

       14. How do I put an array of strings completely in ROM?

       15. How to use external RAM?

       16. Which -O flag to use?

       17. How do I relocate code to a fixed address?

       18. My UART is generating nonsense! My ATmega128 keeps crashing! Port F is completely
           broken!

       19. Why do all my 'foo...bar' strings eat up the SRAM?

       20. Why does the compiler compile an 8-bit operation that uses bitwise operators into a
           16-bit operation in assembly?

       21. How to detect RAM memory and variable overlap problems?

       22. Is it really impossible to program the ATtinyXX in C?

       23. What is this 'clock skew detected' message?

       24. Why are (many) interrupt flags cleared by writing a logical 1?

       25. Why have 'programmed' fuses the bit value 0?

       26. Which AVR-specific assembler operators are available?

       27. Why are interrupts re-enabled in the middle of writing the stack pointer?

       28. Why are there five different linker scripts?

       29. How to add a raw binary image to linker output?

       30. How do I perform a software reset of the AVR?

       31. I am using floating point math. Why is the compiled code so big? Why does my code not
           work?

       32. What pitfalls exist when writing reentrant code?

       33. Why are some addresses of the EEPROM corrupted (usually address zero)?

       34. Why is my baud rate wrong?

       35. On a device with more than 128 KiB of flash, how to make function pointers work?

My program doesn't recognize a variable updated within an interrupt routine

       When using the optimizer, in a loop like the following one:

       uint8_t flag;
       ISR(SOME_vect) {
         flag = 1;
       }

               while (flag == 0) {
                       ...
               }

       the compiler will typically access flag only once, and optimize further accesses
       completely away, since its code path analysis shows that nothing inside the loop could
       change the value of flag anyway. To tell the compiler that this variable could be changed
       outside the scope of its code path analysis (e. g. from within an interrupt routine), the
       variable needs to be declared like:

       volatile uint8_t flag;

       Back to FAQ Index.

I get 'undefined reference to...' for functions like 'sin()'

       In order to access the mathematical functions that are declared in <math.h>, the linker
       needs to be told to also link the mathematical library, libm.a.

       Typically, system libraries like libm.a are given to the final C compiler command line
       that performs the linking step by adding a flag -lm at the end. (That is, the initial lib
       and the filename suffix from the library are written immediately after a -l flag. So for a
       libfoo.a library, -lfoo needs to be provided.) This will make the linker search the
       library in a path known to the system.

       An alternative would be to specify the full path to the libm.a file at the same place on
       the command line, i. e. after all the object files (*.o). However, since this requires
       knowledge of where the build system will exactly find those library files, this is
       deprecated for system libraries.

       Back to FAQ Index.

How to permanently bind a variable to a register?

       This can be done with

       register unsigned char counter asm('r3');

       Typically, it should be safe to use r2 through r7 that way.

       Registers r8 through r15 can be used for argument passing by the compiler in case many or
       long arguments are being passed to callees. If this is not the case throughout the entire
       application, these registers could be used for register variables as well.

       Extreme care should be taken that the entire application is compiled with a consistent set
       of register-allocated variables, including possibly used library functions.

       See C Names Used in Assembler Code for more details.

       Back to FAQ Index.

How to modify MCUCR or WDTCR early?

       The method of early initialization (MCUCR, WDTCR or anything else) is different (and more
       flexible) in the current version. Basically, write a small assembler file which looks like
       this:

       ;; begin xram.S

       #include <avr/io.h>

               .section .init1,'ax',@progbits

               ldi r16,_BV(SRE) | _BV(SRW)
               out _SFR_IO_ADDR(MCUCR),r16

       ;; end xram.S

       Assemble it, link the resulting xram.o with other files in your program, and this piece of
       code will be inserted in initialization code, which is run right after reset. See the
       linker script for comments about the new .initN sections (which one to use, etc.).

       The advantage of this method is that you can insert any initialization code you want (just
       remember that this is very early startup -- no stack and no __zero_reg__ yet), and no
       program memory space is wasted if this feature is not used.

       There should be no need to modify linker scripts anymore, except for some very special
       cases. It is best to leave __stack at its default value (end of internal SRAM -- faster,
       and required on some devices like ATmega161 because of errata), and add
       -Wl,-Tdata,0x801100 to start the data section above the stack.

       For more information on using sections, see Memory Sections. There is also an example for
       Using Sections in C Code. Note that in C code, any such function would preferably be
       placed into section .init3 as the code in .init2 ensures the internal register
       __zero_reg__ is already cleared.

       Back to FAQ Index.

What is all this _BV() stuff about?

       When performing low-level output work, which is a very central point in microcontroller
       programming, it is quite common that a particular bit needs to be set or cleared in some
       IO register. While the device documentation provides mnemonic names for the various bits
       in the IO registers, and the AVR device-specific IO definitions reflect these names in
       definitions for numerical constants, a way is needed to convert a bit number (usually
       within a byte register) into a byte value that can be assigned directly to the register.
       However, sometimes the direct bit numbers are needed as well (e. g. in an SBI()
       instruction), so the definitions cannot usefully be made as byte values in the first
       place.

       So in order to access a particular bit number as a byte value, use the _BV() macro. Of
       course, the implementation of this macro is just the usual bit shift (which is done by the
       compiler anyway, thus doesn't impose any run-time penalty), so the following applies:

       _BV(3) => 1 << 3 => 0x08

       However, using the macro often makes the program better readable.

       Example: clock timer 2 with full IO clock (CS2x = 0b001), toggle OC2 output on compare
       match (COM2x = 0b01), and clear timer on compare match (CTC2 = 1). Make OC2 (PD7) an
       output.

               TCCR2 = _BV(COM20)|_BV(CTC2)|_BV(CS20);
               DDRD = _BV(PD7);

       Back to FAQ Index.

Can I use C++ on the AVR?

       Basically yes, C++ is supported (assuming your compiler has been configured and compiled
       to support it, of course). Source files ending in .cc, .cpp or .C will automatically cause
       the compiler frontend to invoke the C++ compiler. Alternatively, the C++ compiler could be
       explicitly called by the name avr-c++.

       However, there's currently no support for libstdc++, the standard support library needed
       for a complete C++ implementation. This imposes a number of restrictions on the C++
       programs that can be compiled. Among them are:

       · Obviously, none of the C++ related standard functions, classes, and template classes are
         available.

       · The operators new and delete are not implemented, attempting to use them will cause the
         linker to complain about undefined external references. (This could perhaps be fixed.)

       · Some of the supplied include files are not C++ safe, i. e. they need to be wrapped into

        extern 'C' { . . . }

        (This could certainly be fixed, too.)

       · Exceptions are not supported. Since exceptions are enabled by default in the C++
         frontend, they explicitly need to be turned off using -fno-exceptions in the compiler
         options. Failing this, the linker will complain about an undefined external reference to
         __gxx_personality_sj0.

       Constructors and destructors are supported though, including global ones.

       When programming C++ in space- and runtime-sensitive environments like microcontrollers,
       extra care should be taken to avoid unwanted side effects of the C++ calling conventions
       like implied copy constructors that could be called upon function invocation etc. These
       things could easily add up into a considerable amount of time and program memory wasted.
       Thus, casual inspection of the generated assembler code (using the -S compiler option)
       seems to be warranted.

       Back to FAQ Index.

Shouldn't I initialize all my variables?

       Global and static variables are guaranteed to be initialized to 0 by the C standard. avr-
       gcc does this by placing the appropriate code into section .init4 (see The .initN
       Sections). With respect to the standard, this sentence is somewhat simplified (because the
       standard allows for machines where the actual bit pattern used differs from all bits being
       0), but for the AVR target, in general, all integer-type variables are set to 0, all
       pointers to a NULL pointer, and all floating-point variables to 0.0.

       As long as these variables are not initialized (i. e. they don't have an equal sign and an
       initialization expression to the right within the definition of the variable), they go
       into the .bss section of the file. This section simply records the size of the variable,
       but otherwise doesn't consume space, neither within the object file nor within flash
       memory. (Of course, being a variable, it will consume space in the target's SRAM.)

       In contrast, global and static variables that have an initializer go into the .data
       section of the file. This will cause them to consume space in the object file (in order to
       record the initializing value), and in the flash ROM of the target device. The latter is
       needed since the flash ROM is the only way that the compiler can tell the target device
       the value this variable is going to be initialized to.

       Now if some programmer 'wants to make doubly sure' their variables really get a 0 at
       program startup, and adds an initializer just containing 0 on the right-hand side, they
       waste space. While this waste of space applies to virtually any platform C is implemented
       on, it's usually not noticeable on larger machines like PCs, while the waste of flash ROM
       storage can be very painful on a small microcontroller like the AVR.

       So in general, variables should only be explicitly initialized if the initial value is
       non-zero.

       Note:
           Recent versions of GCC are now smart enough to detect this situation, and revert
           variables that are explicitly initialized to 0 to the .bss section. Still, other
           compilers might not do that optimization, and as the C standard guarantees the
           initialization, it is safe to rely on it.

       Back to FAQ Index.

Why do some 16-bit timer registers sometimes get trashed?

       Some of the timer-related 16-bit IO registers use a temporary register (called TEMP in the
       Atmel datasheet) to guarantee an atomic access to the register despite the fact that two
       separate 8-bit IO transfers are required to actually move the data. Typically, this
       includes access to the current timer/counter value register (TCNTn), the input capture
       register (ICRn), and write access to the output compare registers (OCRnM). Refer to the
       actual datasheet for each device's set of registers that involves the TEMP register.

       When accessing one of the registers that use TEMP from the main application, and possibly
       any other one from within an interrupt routine, care must be taken that no access from
       within an interrupt context could clobber the TEMP register data of an in-progress
       transaction that has just started elsewhere.

       To protect interrupt routines against other interrupt routines, it's usually best to use
       the ISR() macro when declaring the interrupt function, and to ensure that interrupts are
       still disabled when accessing those 16-bit timer registers.

       Within the main program, access to those registers could be encapsulated in calls to the
       cli() and sei() macros. If the status of the global interrupt flag before accessing one of
       those registers is uncertain, something like the following example code can be used.

       uint16_t
       read_timer1(void)
       {
               uint8_t sreg;
               uint16_t val;

               sreg = SREG;
               cli();
               val = TCNT1;
               SREG = sreg;

               return val;
       }

       Back to FAQ Index.

How do I use a #define'd constant in an asm statement?

       So you tried this:

       asm volatile('sbi 0x18,0x07;');

       Which works. When you do the same thing but replace the address of the port by its macro
       name, like this:

       asm volatile('sbi PORTB,0x07;');

       you get a compilation error: 'Error: constant value required'.

       PORTB is a precompiler definition included in the processor specific file included in
       avr/io.h. As you may know, the precompiler will not touch strings and PORTB, instead of
       0x18, gets passed to the assembler. One way to avoid this problem is:

       asm volatile('sbi %0, 0x07' : 'I' (_SFR_IO_ADDR(PORTB)):);

       Note:
           For C programs, rather use the standard C bit operators instead, so the above would be
           expressed as PORTB |= (1 << 7). The optimizer will take care to transform this into a
           single SBI instruction, assuming the operands allow for this.

       Back to FAQ Index.

Why does the PC randomly jump around when single-stepping through my program in avr-gdb?

       When compiling a program with both optimization (-O) and debug information (-g) which is
       fortunately possible in avr-gcc, the code watched in the debugger is optimized code. While
       it is not guaranteed, very often this code runs with the exact same optimizations as it
       would run without the -g switch.

       This can have unwanted side effects. Since the compiler is free to reorder code execution
       as long as the semantics do not change, code is often rearranged in order to make it
       possible to use a single branch instruction for conditional operations. Branch
       instructions can only cover a short range for the target PC (-63 through +64 words from
       the current PC). If a branch instruction cannot be used directly, the compiler needs to
       work around it by combining a skip instruction together with a relative jump (rjmp)
       instruction, which will need one additional word of ROM.

       Another side effect of optimization is that variable usage is restricted to the area of
       code where it is actually used. So if a variable was placed in a register at the beginning
       of some function, this same register can be re-used later on if the compiler notices that
       the first variable is no longer used inside that function, even though the variable is
       still in lexical scope. When trying to examine the variable in avr-gdb, the displayed
       result will then look garbled.

       So in order to avoid these side effects, optimization can be turned off while debugging.
       However, some of these optimizations might also have the side effect of uncovering bugs
       that would otherwise not be obvious, so it must be noted that turning off optimization can
       easily change the bug pattern. In most cases, you are better off leaving optimizations
       enabled while debugging.

       Back to FAQ Index.

How do I trace an assembler file in avr-gdb?

       When using the -g compiler option, avr-gcc only generates line number and other debug
       information for C (and C++) files that pass the compiler. Functions that don't have line
       number information will be completely skipped by a single step command in gdb. This
       includes functions linked from a standard library, but by default also functions defined
       in an assembler source file, since the -g compiler switch does not apply to the assembler.

       So in order to debug an assembler input file (possibly one that has to be passed through
       the C preprocessor), it's the assembler that needs to be told to include line-number
       information into the output file. (Other debug information like data types and variable
       allocation cannot be generated, since unlike a compiler, the assembler basically doesn't
       know about this.) This is done using the (GNU) assembler option --gstabs.

       Example:

         $ avr-as -mmcu=atmega128 --gstabs -o foo.o foo.s

       When the assembler is not called directly but through the C compiler frontend (either
       implicitly by passing a source file ending in .S, or explicitly using -x assembler-with-
       cpp), the compiler frontend needs to be told to pass the --gstabs option down to the
       assembler. This is done using -Wa,--gstabs. Please take care to only pass this option when
       compiling an assembler input file. Otherwise, the assembler code that results from the C
       compilation stage will also get line number information, which confuses the debugger.

       Note:
           You can also use -Wa,-gstabs since the compiler will add the extra '-' for you.

       Example:

         $ EXTRA_OPTS="-Wall -mmcu=atmega128 -x assembler-with-cpp"
         $ avr-gcc -Wa,--gstabs ${EXTRA_OPTS} -c -o foo.o foo.S

       Also note that the debugger might get confused when entering a piece of code that has a
       non-local label before, since it then takes this label as the name of a new function that
       appears to have been entered. Thus, the best practice to avoid this confusion is to only
       use non-local labels when declaring a new function, and restrict anything else to local
       labels. Local labels consist just of a number only. References to these labels consist of
       the number, followed by the letter b for a backward reference, or f for a forward
       reference. These local labels may be re-used within the source file, references will pick
       the closest label with the same number and given direction.

       Example:

       myfunc: push    r16
               push    r17
               push    r18
               push    YL
               push    YH
               ...
               eor     r16, r16        ; start loop
               ldi     YL, lo8(sometable)
               ldi     YH, hi8(sometable)
               rjmp    2f              ; jump to loop test at end
       1:      ld      r17, Y+         ; loop continues here
               ...
               breq    1f              ; return from myfunc prematurely
               ...
               inc     r16
       2:      cmp     r16, r18
               brlo    1b              ; jump back to top of loop

       1:      pop     YH
               pop     YL
               pop     r18
               pop     r17
               pop     r16
               ret

       Back to FAQ Index.

How do I pass an IO port as a parameter to a function?

       Consider this example code:

       #include <inttypes.h>
       #include <avr/io.h>

       void
       set_bits_func_wrong (volatile uint8_t port, uint8_t mask)
       {
           port |= mask;
       }

       void
       set_bits_func_correct (volatile uint8_t *port, uint8_t mask)
       {
           *port |= mask;
       }

       #define set_bits_macro(port,mask) ((port) |= (mask))

       int main (void)
       {
           set_bits_func_wrong (PORTB, 0xaa);
           set_bits_func_correct (&PORTB, 0x55);
           set_bits_macro (PORTB, 0xf0);

           return (0);
       }

       The first function will generate object code which is not even close to what is intended.
       The major problem arises when the function is called. When the compiler sees this call, it
       will actually pass the value of the PORTB register (using an IN instruction), instead of
       passing the address of PORTB (e.g. memory mapped io addr of 0x38, io port 0x18 for the
       mega128). This is seen clearly when looking at the disassembly of the call:

           set_bits_func_wrong (PORTB, 0xaa);
        10a:   6a ea           ldi     r22, 0xAA       ; 170
        10c:   88 b3           in      r24, 0x18       ; 24
        10e:   0e 94 65 00     call    0xca

       So, the function, once called, only sees the value of the port register and knows nothing
       about which port it came from. At this point, whatever object code is generated for the
       function by the compiler is irrelevant. The interested reader can examine the full
       disassembly to see that the function's body is completely fubar.

       The second function shows how to pass (by reference) the memory mapped address of the io
       port to the function so that you can read and write to it in the function. Here's the
       object code generated for the function call:

           set_bits_func_correct (&PORTB, 0x55);
        112:   65 e5           ldi     r22, 0x55       ; 85
        114:   88 e3           ldi     r24, 0x38       ; 56
        116:   90 e0           ldi     r25, 0x00       ; 0
        118:   0e 94 7c 00     call    0xf8

       You can clearly see that 0x0038 is correctly passed for the address of the io port.
       Looking at the disassembled object code for the body of the function, we can see that the
       function is indeed performing the operation we intended:

       void
       set_bits_func_correct (volatile uint8_t *port, uint8_t mask)
       {
         f8:   fc 01           movw    r30, r24
           *port |= mask;
         fa:   80 81           ld      r24, Z
         fc:   86 2b           or      r24, r22
         fe:   80 83           st      Z, r24
       }
        100:   08 95           ret

       Notice that we are accessing the io port via the LD and ST instructions.

       The port parameter must be volatile to avoid a compiler warning.

       Note:
           Because of the nature of the IN and OUT assembly instructions, they can not be used
           inside the function when passing the port in this way. Readers interested in the
           details should consult the Instruction Set datasheet.

       Finally we come to the macro version of the operation. In this contrived example, the
       macro is the most efficient method with respect to both execution speed and code size:

           set_bits_macro (PORTB, 0xf0);
        11c:   88 b3           in      r24, 0x18       ; 24
        11e:   80 6f           ori     r24, 0xF0       ; 240
        120:   88 bb           out     0x18, r24       ; 24

       Of course, in a real application, you might be doing a lot more in your function which
       uses a passed by reference io port address and thus the use of a function over a macro
       could save you some code space, but still at a cost of execution speed.

       Care should be taken when such an indirect port access is going to one of the 16-bit IO
       registers where the order of write access is critical (like some timer registers). All
       versions of avr-gcc up to 3.3 will generate instructions that use the wrong access order
       in this situation (since with normal memory operands where the order doesn't matter, this
       sometimes yields shorter code).

       See http://mail.nongnu.org/archive/html/avr-libc-dev/2003-01/msg00044.html for a possible
       workaround.

       avr-gcc versions after 3.3 have been fixed in a way where this optimization will be
       disabled if the respective pointer variable is declared to be volatile, so the correct
       behaviour for 16-bit IO ports can be forced that way.

       Back to FAQ Index.

What registers are used by the C compiler?

       · Data types:
          char is 8 bits, int is 16 bits, long is 32 bits, long long is 64 bits, float and double
         are 32 bits (this is the only supported floating point format), pointers are 16 bits
         (function pointers are word addresses, to allow addressing up to 128K program memory
         space). There is a -mint8 option (see Options for the C compiler avr-gcc) to make int 8
         bits, but that is not supported by avr-libc and violates C standards (int must be at
         least 16 bits). It may be removed in a future release.

       · Call-used registers (r18-r27, r30-r31):
          May be allocated by gcc for local data. You may use them freely in assembler
         subroutines. Calling C subroutines can clobber any of them - the caller is responsible
         for saving and restoring.

       · Call-saved registers (r2-r17, r28-r29):
          May be allocated by gcc for local data. Calling C subroutines leaves them unchanged.
         Assembler subroutines are responsible for saving and restoring these registers, if
         changed. r29:r28 (Y pointer) is used as a frame pointer (points to local data on stack)
         if necessary. The requirement for the callee to save/preserve the contents of these
         registers even applies in situations where the compiler assigns them for argument
         passing.

       · Fixed registers (r0, r1):
          Never allocated by gcc for local data, but often used for fixed purposes:

       r0 - temporary register, can be clobbered by any C code (except interrupt handlers which
       save it), may be used to remember something for a while within one piece of assembler code

       r1 - assumed to be always zero in any C code, may be used to remember something for a
       while within one piece of assembler code, but must then be cleared after use (clr r1).
       This includes any use of the [f]mul[s[u]] instructions, which return their result in
       r1:r0. Interrupt handlers save and clear r1 on entry, and restore r1 on exit (in case it
       was non-zero).

       · Function call conventions:
          Arguments - allocated left to right, r25 to r8. All arguments are aligned to start in
         even-numbered registers (odd-sized arguments, including char, have one free register
         above them). This allows making better use of the movw instruction on the enhanced core.

       If too many, those that don't fit are passed on the stack.

       Return values: 8-bit in r24 (not r25!), 16-bit in r25:r24, up to 32 bits in r22-r25, up to
       64 bits in r18-r25. 8-bit return values are zero/sign-extended to 16 bits by the called
       function (unsigned char is more efficient than signed char - just clr r25). Arguments to
       functions with variable argument lists (printf etc.) are all passed on stack, and char is
       extended to int.

       Warning:
           There was no such alignment before 2000-07-01, including the old patches for
           gcc-2.95.2. Check your old assembler subroutines, and adjust them accordingly.

       Back to FAQ Index.

How do I put an array of strings completely in ROM?

       There are times when you may need an array of strings which will never be modified. In
       this case, you don't want to waste ram storing the constant strings. The most obvious (and
       incorrect) thing to do is this:

       #include <avr/pgmspace.h>

       PGM_P array[2] PROGMEM = {
           'Foo',
           'Bar'
       };

       int main (void)
       {
           char buf[32];
           strcpy_P (buf, array[1]);
           return 0;
       }

       The result is not what you want though. What you end up with is the array stored in ROM,
       while the individual strings end up in RAM (in the .data section).

       To work around this, you need to do something like this:

       #include <avr/pgmspace.h>

       const char foo[] PROGMEM = 'Foo';
       const char bar[] PROGMEM = 'Bar';

       PGM_P array[2] PROGMEM = {
           foo,
           bar
       };

       int main (void)
       {
           char buf[32];
           PGM_P p;
           int i;

           memcpy_P(&p, &array[i], sizeof(PGM_P));
           strcpy_P(buf, p);
           return 0;
       }

       Looking at the disassembly of the resulting object file we see that array is in flash as
       such:

       00000026 <array>:
         26:   2e 00           .word   0x002e  ; ????
         28:   2a 00           .word   0x002a  ; ????

       0000002a <bar>:
         2a:   42 61 72 00                                         Bar.

       0000002e <foo>:
         2e:   46 6f 6f 00                                         Foo.

       foo is at addr 0x002e.
        bar is at addr 0x002a.
        array is at addr 0x0026.

       Then in main we see this:

           memcpy_P(&p, &array[i], sizeof(PGM_P));
         70:   66 0f           add     r22, r22
         72:   77 1f           adc     r23, r23
         74:   6a 5d           subi    r22, 0xDA       ; 218
         76:   7f 4f           sbci    r23, 0xFF       ; 255
         78:   42 e0           ldi     r20, 0x02       ; 2
         7a:   50 e0           ldi     r21, 0x00       ; 0
         7c:   ce 01           movw    r24, r28
         7e:   81 96           adiw    r24, 0x21       ; 33
         80:   08 d0           rcall   .+16            ; 0x92

       This code reads the pointer to the desired string from the ROM table array into a register
       pair.

       The value of i (in r22:r23) is doubled to accommodate for the word offset required to
       access array[], then the address of array (0x26) is added, by subtracting the negated
       address (0xffda). The address of variable p is computed by adding its offset within the
       stack frame (33) to the Y pointer register, and memcpy_P is called.

           strcpy_P(buf, p);
         82:   69 a1           ldd     r22, Y+33       ; 0x21
         84:   7a a1           ldd     r23, Y+34       ; 0x22
         86:   ce 01           movw    r24, r28
         88:   01 96           adiw    r24, 0x01       ; 1
         8a:   0c d0           rcall   .+24            ; 0xa4

       This will finally copy the ROM string into the local buffer buf.

       Variable p (located at Y+33) is read, and passed together with the address of buf (Y+1) to
       strcpy_P. This will copy the string from ROM to buf.

       Note that when using a compile-time constant index, omitting the first step (reading the
       pointer from ROM via memcpy_P) usually remains unnoticed, since the compiler would then
       optimize the code for accessing array at compile-time.

       Back to FAQ Index.

How to use external RAM?

       Well, there is no universal answer to this question; it depends on what the external RAM
       is going to be used for.

       Basically, the bit SRE (SRAM enable) in the MCUCR register needs to be set in order to
       enable the external memory interface. Depending on the device to be used, and the
       application details, further registers affecting the external memory operation like XMCRA
       and XMCRB, and/or further bits in MCUCR might be configured. Refer to the datasheet for
       details.

       If the external RAM is going to be used to store the variables from the C program (i. e.,
       the .data and/or .bss segment) in that memory area, it is essential to set up the external
       memory interface early during the device initialization so the initialization of these
       variable will take place. Refer to How to modify MCUCR or WDTCR early? for a description
       how to do this using few lines of assembler code, or to the chapter about memory sections
       for an example written in C.

       The explanation of malloc() contains a discussion about the use of internal RAM vs.
       external RAM in particular with respect to the various possible locations of the heap
       (area reserved for malloc()). It also explains the linker command-line options that are
       required to move the memory regions away from their respective standard locations in
       internal RAM.

       Finally, if the application simply wants to use the additional RAM for private data
       storage kept outside the domain of the C compiler (e. g. through a char * variable
       initialized directly to a particular address), it would be sufficient to defer the
       initialization of the external RAM interface to the beginning of main(), so no tweaking of
       the .init3 section is necessary. The same applies if only the heap is going to be located
       there, since the application start-up code does not affect the heap.

       It is not recommended to locate the stack in external RAM. In general, accessing external
       RAM is slower than internal RAM, and errata of some AVR devices even prevent this
       configuration from working properly at all.

       Back to FAQ Index.

Which -O flag to use?

       There's a common misconception that larger numbers behind the -O option might
       automatically cause 'better' optimization. First, there's no universal definition for
       'better', with optimization often being a speed vs. code size trade off. See the detailed
       discussion for which option affects which part of the code generation.

       A test case was run on an ATmega128 to judge the effect of compiling the library itself
       using different optimization levels. The following table lists the results. The test case
       consisted of around 2 KB of strings to sort. Test #1 used qsort() using the standard
       library strcmp(), test #2 used a function that sorted the strings by their size (thus had
       two calls to strlen() per invocation).

       When comparing the resulting code size, it should be noted that a floating point version
       of fvprintf() was linked into the binary (in order to print out the time elapsed) which is
       entirely not affected by the different optimization levels, and added about 2.5 KB to the
       code.

       Optimization flags Size of .text Time for test #1 Time for test #2  -O3 6898 903 µs 19.7
       ms  -O2 6666 972 µs 20.1 ms  -Os 6618 955 µs 20.1 ms  -Os -mcall-prologues 6474 972 µs
       20.1 ms

       (The difference between 955 µs and 972 µs was just a single timer-tick, so take this with
       a grain of salt.)

       So generally, it seems -Os -mcall-prologues is the most universal 'best' optimization
       level. Only applications that need to get the last few percent of speed benefit from using
       -O3.

       Back to FAQ Index.

How do I relocate code to a fixed address?

       First, the code should be put into a new named section. This is done with a section
       attribute:

       __attribute__ ((section ('.bootloader')))

       In this example, .bootloader is the name of the new section. This attribute needs to be
       placed after the prototype of any function to force the function into the new section.

       void boot(void) __attribute__ ((section ('.bootloader')));

       To relocate the section to a fixed address the linker flag --section-start is used. This
       option can be passed to the linker using the -Wl compiler option:

       -Wl,--section-start=.bootloader=0x1E000

       The name after section-start is the name of the section to be relocated. The number after
       the section name is the beginning address of the named section.

       Back to FAQ Index.

My UART is generating nonsense! My ATmega128 keeps crashing! Port F is completely broken!

       Well, certain odd problems arise out of the situation that the AVR devices as shipped by
       Atmel often come with a default fuse bit configuration that doesn't match the user's
       expectations. Here is a list of things to care for:

       · All devices that have an internal RC oscillator ship with the fuse enabled that causes
         the device to run off this oscillator, instead of an external crystal. This often
         remains unnoticed until the first attempt is made to use something critical in timing,
         like UART communication.

       · The ATmega128 ships with the fuse enabled that turns this device into ATmega103
         compatibility mode. This means that some ports are not fully usable, and in particular
         that the internal SRAM is located at lower addresses. Since by default, the stack is
         located at the top of internal SRAM, a program compiled for an ATmega128 running on such
         a device will immediately crash upon the first function call (or rather, upon the first
         function return).

       · Devices with a JTAG interface have the JTAGEN fuse programmed by default. This will make
         the respective port pins that are used for the JTAG interface unavailable for regular
         IO.

       Back to FAQ Index.

Why do all my 'foo...bar' strings eat up the SRAM?

       By default, all strings are handled as all other initialized variables: they occupy RAM
       (even though the compiler might warn you when it detects write attempts to these RAM
       locations), and occupy the same amount of flash ROM so they can be initialized to the
       actual string by startup code. The compiler can optimize multiple identical strings into a
       single one, but obviously only for one compilation unit (i. e., a single C source file).

       That way, any string literal will be a valid argument to any C function that expects a
       const char * argument.

       Of course, this is going to waste a lot of SRAM. In Program Space String Utilities, a
       method is described how such constant data can be moved out to flash ROM. However, a
       constant string located in flash ROM is no longer a valid argument to pass to a function
       that expects a const char *-type string, since the AVR processor needs the special
       instruction LPM to access these strings. Thus, separate functions are needed that take
       this into account. Many of the standard C library functions have equivalents available
       where one of the string arguments can be located in flash ROM. Private functions in the
       applications need to handle this, too. For example, the following can be used to implement
       simple debugging messages that will be sent through a UART:

       #include <inttypes.h>
       #include <avr/io.h>
       #include <avr/pgmspace.h>

       int
       uart_putchar(char c)
       {
         if (c == '0)    ');
           uart_putchar('
         loop_until_bit_is_set(USR, UDRE);
         UDR = c;
         return 0; /* so it could be used for fdevopen(), too */
       }

       void
       debug_P(const char *addr)
       {
         char c;

         while ((c = pgm_read_byte(addr++)))
           uart_putchar(c);
       }

       int
       main(void)
       {
         ioinit(); /* initialize UART, ... */
         debug_P(PSTR('foo was here0));
         return 0;
       }

       Note:
           By convention, the suffix _P to the function name is used as an indication that this
           function is going to accept a 'program-space string'. Note also the use of the PSTR()
           macro.

       Back to FAQ Index.

Why does the compiler compile an 8-bit operation that uses bitwise operators into a 16-bit

       operation in assembly?
       Bitwise operations in Standard C will automatically promote their operands to an int,
       which is (by default) 16 bits in avr-gcc.

       To work around this use typecasts on the operands, including literals, to declare that the
       values are to be 8 bit operands.

       This may be especially important when clearing a bit:

       var &= ~mask;  /* wrong way! */

       The bitwise 'not' operator (~) will also promote the value in mask to an int. To keep it
       an 8-bit value, typecast before the 'not' operator:

       var &= (unsigned char)~mask;

       Back to FAQ Index.

How to detect RAM memory and variable overlap problems?

       You can simply run avr-nm on your output (ELF) file. Run it with the -n option, and it
       will sort the symbols numerically (by default, they are sorted alphabetically).

       Look for the symbol _end, that's the first address in RAM that is not allocated by a
       variable. (avr-gcc internally adds 0x800000 to all data/bss variable addresses, so please
       ignore this offset.) Then, the run-time initialization code initializes the stack pointer
       (by default) to point to the last available address in (internal) SRAM. Thus, the region
       between _end and the end of SRAM is what is available for stack. (If your application uses
       malloc(), which e. g. also can happen inside printf(), the heap for dynamic memory is also
       located there. See Memory Areas and Using malloc().)

       The amount of stack required for your application cannot be determined that easily. For
       example, if you recursively call a function and forget to break that recursion, the amount
       of stack required is infinite. :-) You can look at the generated assembler code (avr-gcc
       ... -S), there's a comment in each generated assembler file that tells you the frame size
       for each generated function. That's the amount of stack required for this function, you
       have to add up that for all functions where you know that the calls could be nested.

       Back to FAQ Index.

Is it really impossible to program the ATtinyXX in C?

       While some small AVRs are not directly supported by the C compiler since they do not have
       a RAM-based stack (and some do not even have RAM at all), it is possible anyway to use the
       general-purpose registers as a RAM replacement since they are mapped into the data memory
       region.

       Bruce D. Lightner wrote an excellent description of how to do this, and offers this
       together with a toolkit on his web page:

       http://lightner.net/avr/ATtinyAvrGcc.html

       Back to FAQ Index.

What is this 'clock skew detected' message?

       It's a known problem of the MS-DOS FAT file system. Since the FAT file system has only a
       granularity of 2 seconds for maintaining a file's timestamp, and it seems that some MS-DOS
       derivative (Win9x) perhaps rounds up the current time to the next second when calculating
       the timestamp of an updated file in case the current time cannot be represented in FAT's
       terms, this causes a situation where make sees a 'file coming from the future'.

       Since all make decisions are based on file timestamps, and their dependencies, make warns
       about this situation.

       Solution: don't use inferior file systems / operating systems. Neither Unix file systems
       nor HPFS (aka NTFS) do experience that problem.

       Workaround: after saving the file, wait a second before starting make. Or simply ignore
       the warning. If you are paranoid, execute a make clean all to make sure everything gets
       rebuilt.

       In networked environments where the files are accessed from a file server, this message
       can also happen if the file server's clock differs too much from the network client's
       clock. In this case, the solution is to use a proper time keeping protocol on both
       systems, like NTP. As a workaround, synchronize the client's clock frequently with the
       server's clock.

       Back to FAQ Index.

Why are (many) interrupt flags cleared by writing a logical 1?

       Usually, each interrupt has its own interrupt flag bit in some control register,
       indicating the specified interrupt condition has been met by representing a logical 1 in
       the respective bit position. When working with interrupt handlers, this interrupt flag bit
       usually gets cleared automatically in the course of processing the interrupt, sometimes by
       just calling the handler at all, sometimes (e. g. for the U[S]ART) by reading a particular
       hardware register that will normally happen anyway when processing the interrupt.

       From the hardware's point of view, an interrupt is asserted as long as the respective bit
       is set, while global interrupts are enabled. Thus, it is essential to have the bit cleared
       before interrupts get re-enabled again (which usually happens when returning from an
       interrupt handler).

       Only few subsystems require an explicit action to clear the interrupt request when using
       interrupt handlers. (The notable exception is the TWI interface, where clearing the
       interrupt indicates to proceed with the TWI bus hardware handshake, so it's never done
       automatically.)

       However, if no normal interrupt handlers are to be used, or in order to make extra sure
       any pending interrupt gets cleared before re-activating global interrupts (e. g. an
       external edge-triggered one), it can be necessary to explicitly clear the respective
       hardware interrupt bit by software. This is usually done by writing a logical 1 into this
       bit position. This seems to be illogical at first, the bit position already carries a
       logical 1 when reading it, so why does writing a logical 1 to it clear the interrupt bit?

       The solution is simple: writing a logical 1 to it requires only a single OUT instruction,
       and it is clear that only this single interrupt request bit will be cleared. There is no
       need to perform a read-modify-write cycle (like, an SBI instruction), since all bits in
       these control registers are interrupt bits, and writing a logical 0 to the remaining bits
       (as it is done by the simple OUT instruction) will not alter them, so there is no risk of
       any race condition that might accidentally clear another interrupt request bit. So instead
       of writing

       TIFR |= _BV(TOV0); /* wrong! */

       simply use

       TIFR = _BV(TOV0);

       Back to FAQ Index.

Why have 'programmed' fuses the bit value 0?

       Basically, fuses are just a bit in a special EEPROM area. For technical reasons, erased
       E[E]PROM cells have all bits set to the value 1, so unprogrammed fuses also have a logical
       1. Conversely, programmed fuse cells read out as bit value 0.

       Back to FAQ Index.

Which AVR-specific assembler operators are available?

       See Pseudo-ops and operators.

       Back to FAQ Index.

Why are interrupts re-enabled in the middle of writing the stack pointer?

       When setting up space for local variables on the stack, the compiler generates code like
       this:

       /* prologue: frame size=20 */
               push r28
               push r29
               in r28,__SP_L__
               in r29,__SP_H__
               sbiw r28,20
               in __tmp_reg__,__SREG__
               cli
               out __SP_H__,r29
               out __SREG__,__tmp_reg__
               out __SP_L__,r28
       /* prologue end (size=10) */

       It reads the current stack pointer value, decrements it by the required amount of bytes,
       then disables interrupts, writes back the high part of the stack pointer, writes back the
       saved SREG (which will eventually re-enable interrupts if they have been enabled before),
       and finally writes the low part of the stack pointer.

       At the first glance, there's a race between restoring SREG, and writing SPL. However,
       after enabling interrupts (either explicitly by setting the I flag, or by restoring it as
       part of the entire SREG), the AVR hardware executes (at least) the next instruction still
       with interrupts disabled, so the write to SPL is guaranteed to be executed with interrupts
       disabled still. Thus, the emitted sequence ensures interrupts will be disabled only for
       the minimum time required to guarantee the integrity of this operation.

       Back to FAQ Index.

Why are there five different linker scripts?

       From a comment in the source code:

       Which one of the five linker script files is actually used depends on command line options
       given to ld.

       A .x script file is the default script A .xr script is for linking without relocation (-r
       flag) A .xu script is like .xr but *do* create constructors (-Ur flag) A .xn script is for
       linking with -n flag (mix text and data on same page). A .xbn script is for linking with
       -N flag (mix text and data on same page).

       Back to FAQ Index.

How to add a raw binary image to linker output?

       The GNU linker avr-ld cannot handle binary data directly. However, there's a companion
       tool called avr-objcopy. This is already known from the output side: it's used to extract
       the contents of the linked ELF file into an Intel Hex load file.

       avr-objcopy can create a relocatable object file from arbitrary binary input, like

       avr-objcopy -I binary -O elf32-avr foo.bin foo.o

       This will create a file named foo.o, with the contents of foo.bin. The contents will
       default to section .data, and two symbols will be created named _binary_foo_bin_start and
       _binary_foo_bin_end. These symbols can be referred to inside a C source to access these
       data.

       If the goal is to have those data go to flash ROM (similar to having used the PROGMEM
       attribute in C source code), the sections have to be renamed while copying, and it's also
       useful to set the section flags:

       avr-objcopy --rename-section .data=.progmem.data,contents,alloc,load,readonly,data -I binary -O elf32-avr foo.bin foo.o

       Note that all this could be conveniently wired into a Makefile, so whenever foo.bin
       changes, it will trigger the recreation of foo.o, and a subsequent relink of the final ELF
       file.

       Below are two Makefile fragments that provide rules to convert a .txt file to an object
       file, and to convert a .bin file to an object file:

       $(OBJDIR)/%.o : %.txt
               @echo Converting $<
               @cp $(<) $(*).tmp
               @echo -n 0 | tr 0 ' 00' >> $(*).tmp
               @$(OBJCOPY) -I binary -O elf32-avr         --rename-section .data=.progmem.data,contents,alloc,load,readonly,data         --redefine-sym _binary_$*_tmp_start=$*         --redefine-sym _binary_$*_tmp_end=$*_end         --redefine-sym _binary_$*_tmp_size=$*_size_sym         $(*).tmp $(@)
               @echo 'extern const char' $(*)'[] PROGMEM;' > $(*).h
               @echo 'extern const char' $(*)_end'[] PROGMEM;' >> $(*).h
               @echo 'extern const char' $(*)_size_sym'[];' >> $(*).h
               @echo '#define $(*)_size ((int)$(*)_size_sym)' >> $(*).h
               @rm $(*).tmp

       $(OBJDIR)/%.o : %.bin
               @echo Converting $<
               @$(OBJCOPY) -I binary -O elf32-avr         --rename-section .data=.progmem.data,contents,alloc,load,readonly,data         --redefine-sym _binary_$*_bin_start=$*         --redefine-sym _binary_$*_bin_end=$*_end         --redefine-sym _binary_$*_bin_size=$*_size_sym         $(<) $(@)
               @echo 'extern const char' $(*)'[] PROGMEM;' > $(*).h
               @echo 'extern const char' $(*)_end'[] PROGMEM;' >> $(*).h
               @echo 'extern const char' $(*)_size_sym'[];' >> $(*).h
               @echo '#define $(*)_size ((int)$(*)_size_sym)' >> $(*).h

       Back to FAQ Index.

How do I perform a software reset of the AVR?

       The canonical way to perform a software reset of non-XMega AVR's is to use the watchdog
       timer. Enable the watchdog timer to the shortest timeout setting, then go into an
       infinite, do-nothing loop. The watchdog will then reset the processor.

       XMega parts have a specific bit RST_SWRST_bm in the RST.CTRL register, that generates a
       hardware reset. RST_SWRST_bm is protected by the XMega Configuration Change Protection
       system.

       The reason why using the watchdog timer or RST_SWRST_bm is preferable over jumping to the
       reset vector, is that when the watchdog or RST_SWRST_bm resets the AVR, the registers will
       be reset to their known, default settings. Whereas jumping to the reset vector will leave
       the registers in their previous state, which is generally not a good idea.

       CAUTION! Older AVRs will have the watchdog timer disabled on a reset. For these older
       AVRs, doing a soft reset by enabling the watchdog is easy, as the watchdog will then be
       disabled after the reset. On newer AVRs, once the watchdog is enabled, then it stays
       enabled, even after a reset! For these newer AVRs a function needs to be added to the
       .init3 section (i.e. during the startup code, before main()) to disable the watchdog early
       enough so it does not continually reset the AVR.

       Here is some example code that creates a macro that can be called to perform a soft reset:

       #include <avr/wdt.h>

       #define soft_reset()        do                          {                               wdt_enable(WDTO_15MS);      for(;;)                     {                           }                       } while(0)

       For newer AVRs (such as the ATmega1281) also add this function to your code to then
       disable the watchdog after a reset (e.g., after a soft reset):

       #include <avr/wdt.h>

       // Function Pototype
       void wdt_init(void) __attribute__((naked)) __attribute__((section('.init3')));

       // Function Implementation
       void wdt_init(void)
       {
           MCUSR = 0;
           wdt_disable();

           return;
       }

       Back to FAQ Index.

I am using floating point math. Why is the compiled code so big? Why does my code not work?

       You are not linking in the math library from AVR-LibC. GCC has a library that is used for
       floating point operations, but it is not optimized for the AVR, and so it generates big
       code, or it could be incorrect. This can happen even when you are not using any floating
       point math functions from the Standard C library, but you are just doing floating point
       math operations.

       When you link in the math library from AVR-LibC, those routines get replaced by hand-
       optimized AVR assembly and it produces much smaller code.

       See I get 'undefined reference to...' for functions like 'sin()' for more details on how
       to link in the math library.

       Back to FAQ Index.

What pitfalls exist when writing reentrant code?

       Reentrant code means the ability for a piece of code to be called simultaneously from two
       or more threads. Attention to re-enterability is needed when using a multi-tasking
       operating system, or when using interrupts since an interrupt is really a temporary
       thread.

       The code generated natively by gcc is reentrant. But, only some of the libraries in avr-
       libc are explicitly reentrant, and some are known not to be reentrant. In general, any
       library call that reads and writes global variables (including I/O registers) is not
       reentrant. This is because more than one thread could read or write the same storage at
       the same time, unaware that other threads are doing the same, and create inconsistent
       and/or erroneous results.

       A library call that is known not to be reentrant will work if it is used only within one
       thread and no other thread makes use of a library call that shares common storage with it.

       Below is a table of library calls with known issues.

       Library call Reentrant Issue Workaround/Alternative  rand(), random() Uses global
       variables to keep state information. Use special reentrant versions: rand_r(), random_r().
       strtod(), strtol(), strtoul() Uses the global variable errno to return success/failure.
       Ignore errno, or protect calls with cli()/sei() or ATOMIC_BLOCK() if the application can
       tolerate it. Or use sccanf() or sccanf_P() if possible.   malloc(), realloc(), calloc(),
       free() Uses the stack pointer and global variables to allocate and free memory. Protect
       calls with cli()/sei() or ATOMIC_BLOCK() if the application can tolerate it. If using an
       OS, use the OS provided memory allocator since the OS is likely modifying the stack
       pointer anyway.   fdevopen(), fclose() Uses calloc() and free(). Protect calls with
       cli()/sei() or ATOMIC_BLOCK() if the application can tolerate it. Or use
       fdev_setup_stream() or FDEV_SETUP_STREAM().
        Note: fclose() will only call free() if the stream has been opened with fdevopen().
       eeprom_*(), boot_*() Accesses I/O registers. Protect calls with cli()/sei(),
       ATOMIC_BLOCK(), or use OS locking.  pgm_*_far() Accesses I/O register RAMPZ. Starting with
       GCC 4.3, RAMPZ is automatically saved for ISRs, so nothing further is needed if only using
       interrupts.
       Some OSes may automatically preserve RAMPZ during context switching. Check the OS
       documentation before assuming it does.
       Otherwise, protect calls with cli()/sei(), ATOMIC_BLOCK(), or use explicit OS locking.
       printf(), printf_P(), vprintf(), vprintf_P(), puts(), puts_P() Alters flags and character
       count in global FILE stdout. Use only in one thread. Or if returned character count is
       unimportant, do not use the *_P versions.
       Note: Formatting to a string output, e.g. sprintf(), sprintf_P(), snprintf(),
       snprintf_P(), vsprintf(), vsprintf_P(), vsnprintf(), vsnprintf_P(), is thread safe. The
       formatted string could then be followed by an fwrite() which simply calls the lower layer
       to send the string.   fprintf(), fprintf_P(), vfprintf(), vfprintf_P(), fputs(), fputs_P()
       Alters flags and character count in the FILE argument. Problems can occur if a global FILE
       is used from multiple threads.  Assign each thread its own FILE for output. Or if returned
       character count is unimportant, do not use the *_P versions.   assert() Contains an
       embedded fprintf(). See above for fprintf(). See above for fprintf().  clearerr() Alters
       flags in the FILE argument.  Assign each thread its own FILE for output.

       getchar(), gets() Alters flags, character count, and unget buffer in global FILE stdin.
       Use only in one thread. ***

       fgetc(), ungetc(), fgets(), scanf(), scanf_P(), fscanf(), fscanf_P(), vscanf(), vfscanf(),
       vfscanf_P(), fread() Alters flags, character count, and unget buffer in the FILE argument.
       Assign each thread its own FILE for input. ***
       Note: Scanning from a string, e.g. sscanf() and sscanf_P(), are thread safe.

       Note:
           It's not clear one would ever want to do character input simultaneously from more than
           one thread anyway, but these entries are included for completeness.

       An effort will be made to keep this table up to date if any new issues are discovered or
       introduced.

       Back to FAQ Index.

Why are some addresses of the EEPROM corrupted (usually address zero)?

       The two most common reason for EEPROM corruption is either writing to the EEPROM beyond
       the datasheet endurance specification, or resetting the AVR while an EEPROM write is in
       progress.

       EEPROM writes can take up to tens of milliseconds to complete. So that the CPU is not tied
       up for that long of time, an internal state-machine handles EEPROM write requests. The
       EEPROM state-machine expects to have all of the EEPROM registers setup, then an EEPROM
       write request to start the process. Once the EEPROM state-machine has started, changing
       EEPROM related registers during an EEPROM write is guaranteed to corrupt the EEPROM write
       process. The datasheet always shows the proper way to tell when a write is in progress, so
       that the registers are not changed by the user's program. The EEPROM state-machine will
       always complete the write in progress unless power is removed from the device.

       As with all EEPROM technology, if power fails during an EEPROM write the state of the byte
       being written is undefined.

       In older generation AVRs the EEPROM Address Register (EEAR) is initialized to zero on
       reset, be it from Brown Out Detect, Watchdog or the Reset Pin. If an EEPROM write has just
       started at the time of the reset, the write will be completed, but now at address zero
       instead of the requested address. If the reset occurs later in the write process both the
       requested address and address zero may be corrupted.

       To distinguish which AVRs may exhibit the corrupt of address zero while a write is in
       process during a reset, look at the 'initial value' section for the EEPROM Address
       Register. If EEAR shows the initial value as 0x00 or 0x0000, then address zero and
       possibly the one being written will be corrupted. Newer parts show the initial value as
       'undefined', these will not corrupt address zero during a reset (unless it was address
       zero that was being written).

       EEPROMs have limited write endurance. The datasheet specifies the number of EEPROM writes
       that are guaranteed to function across the full temperature specification of the AVR, for
       a given byte. A read should always be performed before a write, to see if the value in the
       EEPROM actually needs to be written, so not to cause unnecessary EEPROM wear.

       AVRs use a paging mechanism for doing EEPROM writes. This is almost entirely transparent
       to the user with one exception: When a byte is written to the EEPROM, the entire EEPROM
       page is also transparently erased and (re)written, which will cause wear to bytes that the
       programmer did not explicitly write. If it is desired to extend EEPROM write lifetimes, in
       an attempt not to exceed the datasheet EEPROM write endurance specification for a given
       byte, then writes must be in multiples of the EEPROM page size, and not sequential bytes.
       The EEPROM write page size varies with the device. The EEPROM page size is found in the
       datasheet section on Memory Programming, generally before the Electrical Specifications
       near the end of the datasheet.

       The failure mechanism for an overwritten byte/page is generally one of 'stuck' bits, i. e.
       a bit will stay at a one or zero state regardless of the byte written. Also a write
       followed by a read may return the correct data, but the data will change with the passage
       of time, due the EEPROM's inability to hold a charge from the excessive write wear.

       Back to FAQ Index.

Why is my baud rate wrong?

       Some AVR datasheets give the following formula for calculating baud rates:

       (F_CPU/(UART_BAUD_RATE*16L)-1)

       Unfortunately that formula does not work with all combinations of clock speeds and baud
       rates due to integer truncation during the division operator.

       When doing integer division it is usually better to round to the nearest integer, rather
       than to the lowest. To do this add 0.5 (i. e. half the value of the denominator) to the
       numerator before the division, resulting in the formula:

       ((F_CPU + UART_BAUD_RATE * 8L) / (UART_BAUD_RATE * 16L) - 1)

       This is also the way it is implemented in <util/setbaud.h>: Helper macros for baud rate
       calculations.

       Back to FAQ Index.

On a device with more than 128 KiB of flash, how to make function pointers work?

       Function pointers beyond the 'magical' 128 KiB barrier(s) on larger devices are supposed
       to be resolved through so-called trampolines by the linker, so the actual pointers used in
       the code can remain 16 bits wide.

       In order for this to work, the option -mrelax must be given on the compiler command-line
       that is used to link the final ELF file. (Older compilers did not implement this option
       for the AVR, use -Wl,--relax instead.)

       Back to FAQ Index.