Provided by: xserver-xorg-video-siliconmotion_1.7.5-1build2_amd64 bug

NAME

       siliconmotion - Silicon Motion video driver

SYNOPSIS

       Section "Device"
         Identifier "devname"
         Driver "siliconmotion"
         ...
         [ Option "optionname" ["optionvalue"]]
       EndSection

DESCRIPTION

       siliconmotion is an Xorg driver for Silicon Motion based video cards.  The driver is fully
       accelerated, and provides support for the following framebuffer depths:  8,  16,  and  24.
       All  visual  types  are supported for depth 8, and TrueColor visuals are supported for the
       other depths.

SUPPORTED HARDWARE

       The siliconmotion driver supports PCI and AGP video cards based on the  following  Silicon
       Motion chips:

       Lynx        SM910

       LynxE       SM810

       Lynx3D      SM820

       LynxEM      SM710

       LynxEM+     SM712

       Lynx3DM     SM720

       Cougar3DR   SM731

       MSOC        SM501,SM502

CONFIGURATION DETAILS

       Please  refer to xorg.conf(5) for general configuration details.  This section only covers
       configuration details specific to this driver.  All options names are case and white space
       insensitive when parsed by the server, for example,  "lynxe" and "LynxE" are equivalent.

       Multihead  mode configuration is done through the RandR1.2 interface (see xorg.conf(5) and
       xrandr(1) for further information). Hardware accelerated screen rotation  and  framebuffer
       resizing  are  only  supported with the EXA acceleration architecture (see the AccelMethod
       option below).

       The driver auto-detects the chipset type, but the following ChipSet names  may  optionally
       be specified in the config file "Device" section, and will override the auto-detection:

           "lynx", "lynxe", "lynx3d", "lynxem", "lynxem+", "lynx3dm", "cougar3dr", "msoc".

       The following Cursor Options are supported:

       Option "HWCursor" "boolean"
              Enable or disable the HW cursor.  Default: on.

       Option "SWCursor" "boolean"
              Inverse of "HWCursor".  Default: off.

       The following display Options are supported:

       Option "VideoKey" "integer"
              Set the video color key.  Default: a little off full blue.

       Option "ByteSwap" "boolean"
              Turn on byte swapping for capturing using SMI demo board.  Default: off.

       Option "Interlaced" "boolean"
              Turn on interlaced video capturing.  Default: off.

       Option "UseBIOS" "boolean"
              Use the BIOS to set the modes. This is used for custom panel timings.  Default: off
              for SM72x and SM5xx, otherwise on.

       Option "Dualhead" "boolean"
              Enable dualhead mode.  Currently not all chips are  supported  and  hardware  video
              overlay (XV) support may have some limitations.  Default: off.

       Option "PanelSize" "widthxheight"
              Override LCD panel dimension autodetection.

       Option "UseFBDev" "boolean"
              Don't  actually  program  the  hardware  mode registers, but leave it as set by the
              operating system. Only available on MSOC chips. Default: off.

       Option "CSCVideo" "boolean"
              CSC video uses color space conversion to render video directly to the  framebuffer,
              without using an overlay.  Only available on MSOC chips. Default: on.

       The following video memory Options are supported:

       Option "mclk" "integer"
              Sets  the  memory clock. You must specify the units.  For example 50Mhz is the same
              as 50000Khz or 50000000Hz.  On MSOC chips this is the main  clock  source  for  all
              functional  blocks, such as the 2D engine, GPIO, Video Engine, and DMA Engine. This
              option is only used for debugging purposes  on  MSOC  chips.   Default:  probe  the
              memory clock value, and use it at server start.

       Option "mxclk" "integer"
              Sets  the  memory clock. You must specify the units.  For example 50Mhz is the same
              as 50000Khz or 50000000Hz.  Clock source  for  the  local  SDRAM  controller.  This
              option  is  only  available  on  MSOC  chips  and used only for debugging purposes.
              Default: probe the memory clock value, and use it at server start.

       The following acceleration and graphics engine Options are supported:

       Option "NoAccel"
              Disable acceleration.  Very useful for determining if the driver has problems  with
              drawing  and acceleration routines.  This is the first option to try if your server
              runs but you see graphic corruption on the screen.  Using it decreases performance,
              as  it  uses  software  emulation  for  drawing  operations  the  video  driver can
              accelerate with hardware.  Default: acceleration is enabled.

       Option "AccelMethod" "string"
              Chooses between available acceleration architectures.  Valid options  are  XAA  and
              EXA.   XAA  is the traditional acceleration architecture and support for it is very
              stable.  EXA is a newer acceleration architecture with better performance  for  the
              Render  and  Composite  extensions,  but  the  rendering  code  for it is newer and
              possibly unstable.  The default is XAA.

       The following PCI bus Options are supported:

       Option "PciBurst" "boolean"
              will enable PCI burst mode. This should work on all but a few broken PCI  chipsets,
              and will increase performance.  Default: on.

       Option "PciRetry" "boolean"
              will allow the driver to rely on PCI Retry to program the registers.  PciBurst must
              be enabled for this to work.  This will increase performance, especially for  small
              fills/blits,  because  the  driver does not have to poll the card before sending it
              commands to make sure it is ready. It should work  on  most  recent  PCI  chipsets.
              Default: value of PciBurst option.

SEE ALSO

       Xorg(1), xorg.conf(5), Xserver(1), X(7)

SUPPORT

       For   assistance   with   this  driver,  or  Xorg  in  general,  check  the  web  site  at
       http://www.x.org/.  If you find a problem with Xorg or have a question not answered in the
       FAQ  please  use  our  bug  report  form  available  on  the  web  site  or  send  mail to
       xorg@lists.freedesktop.org.  When reporting problems with the driver send as  much  detail
       as possible, including chipset type, a server output log, and operating system specifics.

AUTHORS

       Kevin  Brosius,  Matt  Grossman,  Harald Koenig, Sebastien Marineau, Mark Vojkovich, Frido
       Garritsen, Corvin Zahn.