Provided by: smokeping_2.6.7-1_all bug


       smokeping_master_slave - How to run multiple distributed instances of SmokePing


       Normally smokeping probes run their tests from the host where smokeping runs to some
       target host and monitor the latency of the connection between the two.

       The Master/Slave concept enables all smokeping probes to run remotely. The use case for
       this is to measure the overall connectivity in a network. If you are interested in
       checking that your central DNS server or your file server works for everyone, you could
       setup several smokeping instances checking up on on the two servers from multiple
       locations within your network. With the Master/Slave smokeping configuration this process
       becomes much simpler, as one smokeping master server can control multiple slaves.

       All monitoring data is stored and presented on the server, but collected by the slaves.
       The slaves will also get their configuration information from the master, so that you just
       have to maintain the master server configuration file and the rest is taken care of


       The slaves communicate with the master smokeping server via the normal smokeping web
       interface. On initial startup each slave connects to the master server and asks for its
       assignments. When the slave has done a round of probing it connects to the master again to
       deliver the results.

       If the assignment for a slave changes, the master will tell the slave after the slave has
       delivered its results.

       The master and the slaves sign their messages by supplying an HMAC-MD5 code (RFC 2104) of
       the message and a shared secret. Optionally the whole communication can run over ssl.

           [slave 1]     [slave 2]      [slave 3]
               |             |              |
               +-------+     |     +--------+
                       |     |     |
                       v     v     v
                     |    master     |

       The slave is a normal smokeping instance setup where the configuration comes from the
       master instead of a local configuration file.  The slave tries to contact the master
       server after every round of probing, supplying its results.  If the master server can not
       be reached, the results will be sent to the server together with the next round of
       results.  Results will be stored in a file in Perl storable form so that they survive a
       restart of the smokeping instance.

   Master Configuration
       To configure a master/slave setup, add a slaves section to your smokeping configuration
       file. Each slave has a section in the slaves part of the master configuration file. The
       section name must match the hostname of the slave. If some configuration parameter must be
       set to a special value for the slave, use an override section to configure this.

       The slave names must be the names the hosts think they have, not their outside hostnames
       or ip addresses or anything like that. When the slave calls the master to get its config
       or report its measurements it will tell the master its 'hostname'. This together with the
       shared secret is used to authenticate and identify who is who.

        *** Slaves ***


        Probes.FPing.binary = /usr/bin/fping

       Then in the targets section you can define slaves at every level. Again the settings get
       inherited by lower order targets and can be overwritten anywhere in the tree.

       A slave will then get the appropriate configuration assigned by the server.

        *** Targets ***
        slaves = slave1 slave2
        slaves =
        slaves = slave1

       The data from the slaves will be stored in TargetName~SlaveName.rrd. So the example above
       would create the following files:


       The slavesecrets.conf file contains a colon separated list of hostnames and secrets.


   Slave Configuration
       A smokeping slave setup has no configuration file. It just needs to know that it runs in
       slave-mode and its secret. The secret is stored in a file for optimal protection. By
       default the persistent data cache will be located in /tmp/smokeping.$USER.cache.

        ./smokeping --master-url=http://smokeping/smokeping.cgi \
                    --cache-dir=/var/smokeping/ \

       The secret.txt file contains a single word, the secret of this slave. It is NOT the same
       as the slavesecrets.conf file the master uses.


       The master effectively has full access to slave hosts as the user running the slave
       smokeping instance.  The configuration is transferred as Perl code that is evaluated on
       the slave.  While this is done inside a restricted "Safe" compartment, there are various
       ways that a malicious master could embed arbitrary commands in the configuration and get
       them to run when the slave probes its targets.

       The strength of the shared secret is thus of paramount importance. Brute forcing the
       secret would enable a man-in-the-middle to inject a malicious new configuration and
       compromise the slave.


       Copyright (c) 2007 by Tobias Oetiker, OETIKER+PARTNER AG. All right reserved.


       This program is free software; you can redistribute it and/or modify it under the terms of
       the GNU General Public License as published by the Free Software Foundation; either
       version 2 of the License, or (at your option) any later version.

       This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
       without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
       See the GNU General Public License for more details.

       You should have received a copy of the GNU General Public License along with this program;
       if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139,


       Tobias Oetiker <>