Provided by: irda-utils_0.9.18-10ubuntu2_i386 bug


       irattach - binds the Linux-IrDA stack to a IrDA port


       irattach [ <dev> ] [ -s ] [ -d dongle ] [ -v ] [ -h ]


       irattach  binds the Linux-IrDA stack to an IrDA port. It configures the
       low level of the Linux-IrDA stack in the kernel. This step  is  usually
       necessary  before you (or applications) can use the higher layer of the
       IrDA stack.

       The irattach command  loads  the  necessary  Linux-IrDA  driver,  which
       configures  the IrDA hardware, and configures the IrDA stack to operate
       on the new IrDA port. Multiple IrDA  ports  can  be  activated  through
       multiple irattach commands.

       irattach  by  default uses the irtty driver which connects to the Linux
       TTY subsystem and use the standard Linux serial driver. This works well
       for  most  machines  and  configurations,  but  limits the baud rate to
       115200bps (IrDA SIR mode). The mode of operation will  work  with  most
       FIR  hardware (as found in laptops - they provide serial emulation) and
       most serial dongles (provided the proper  dongle  type  is  specified),
       making  it  a  safe choice. However, USB dongles and a few FIR hardware
       don't support serial emulation and can't be used with the irtty driver.

       irattach can also use one of  the  Linux  FIR  drivers  (including  USB
       dongle  drivers)  instead of the irtty driver. Most FIR drivers require
       proper configuration of module parameters (this is  documented  below).
       FIR drivers allow you to use higher baud rates (generally up to 4Mbps).
       In general, Linux FIR support is not as stable and mature, due to  lack
       of time and documentation.

       irattach  must  be run as root or installed setuid root, as it requires
       root privileges. If  you  have  compiled  the  IrDA  stack  as  modules
       (recommended),  then  you will need to edit the /etc/modules.conf file.
       See the Infrared-HOWTO for details.


       <dev> : this is the name of a TTY, an IrDA interface  or  IrDA  driver.
       irattach  decides  to  use  the  irtty driver or one of the FIR drivers
       based on this argument.

       · TTY name : this is the serial port to be configured using  the  irtty
         driver,  such  as  /dev/ttyS0. irattach will use the irtty driver, so
         only  SIR  will  be  available.  You  need  to  check   your   serial
         configuration or BIOS to know which serial port is the IrDA port that
         need to be passed to irattach.

       · interface name : this is the device name of an IrDA  interface,  such
         as  irda0.  irattach  will  use one of the FIR drivers (including USB
         dongle drivers). The selected FIR driver must be loaded prior to  the
         call to irattach, or the proper alias for the device name must be set
         in /etc/modules.conf.

       · module name : this is the name of an FIR driver module, such as  nsc-
         ircc  (see list below). All new IrDA interfaces created after loading
         the module will be configured, so this won't work if  the  module  is
         already loaded. This feature is still experimental.

       -s : starts discovery of remote IrDA devices (note that the form "-s 1"
       is no longer supported)

       -v : shows version information (this happens, when no option is  given,

       -h : shows help information.

       -d dongle : attaches an additional dongle driver to the IrDA port.

       You  need  a dongle driver if you have an infrared device that connects
       to your computer's serial port (normal 9-pin  serial  port  connector).
       These  devices are called dongles, and can currently be used by any SIR
       driver (IrTTY or irport).  This  option  is  not  compatible  with  FIR
       drivers, and only works with the irtty and irport drivers.

       The currently known (serial) dongles are:

       · esi        Extended Systems JetEye PC ESI-9680

       · tekram     Tekram IrMate IR-210B dongle

       · actisys    ACTiSYS IR-220L dongle

       · actisys+   ACTiSYS IR-220L+ dongle

       · girbil     Greenwich GIrBIL dongle

       · litelink    Parallax  LiteLink  dongle  &  Extended Systems JetEye PC

       · airport    N.N.

       · old_belkin Belkin (old) SmartBeam dongle or any dongle  only  capable
         of 9600 bauds

       · ep7211      IR port driver for the Cirrus Logic EP7211 processor (ARM

       · mcp2120    Dongles based on the MCP2120 (Microchip)

       · act200l    ACTiSYS Ir-200L dongles

       · ma600      Mobile Action ma600 dongles

       · toim3232   Vishay/Temic TOIM3232 and TOIM4232 based dongles


       If you are one of the lucky people which have  a  FIR  chipset  or  USB
       dongle  that is supported by one of the Linux-IrDA drivers, you can use
       irattach with the interface name of the IrDA  port  to  configure.  You
       will  need  to configure /etc/conf.modules appropriately, with at least
       an alias of irda0 to the driver  name,  or  load  the  driver  manually

       You  don't  strictly need to use irattach with FIR drivers, you can use
       modprobe to load the driver, ifconfig to bring up the interface and set
       the  various  sysctl by hand, but irattach offer a convenient way to do

       Of course, you need to know which FIR driver applies to your  hardware.
       You  may  use  findchip  to get information about the FIR chip. If this
       doesn't help, the Infrared-HOWTO shows other means  to  retrieve  these

       Also, you often need to configure the Linux-serial driver to ignore the
       IrDA port, otherwise both drivers will conflict. This  can  usually  be
       done with setserial /dev/ttySx uart none.

       The currently known FIR drivers are:

       · ali-ircc  ALi  FIR Controller Driver for ALi M5123 (options: io, irq,
         dma).  This driver supports SIR, MIR and FIR  (4Mbps)  speeds.   This
         chipset is used by e.g.:

         The  ALi  M5123  FIR  Controller  is  embedded  in ALi M1543C, M1535,
         M1535D, M1535+, M1535D South Bridge.

       · irda-usb IrDA-USB device driver, for USB devices/dongles that  comply
         with  the official IrDA-USB class specification. Note: USB 2.0 is not
         yet tested.  (options: qos_mtt_bits int,  description  "Minimum  Turn
         Time").  This is used, for e.g.:

         ACTiSYS ACT-IR2000U

         KC Technology KC-180

         Extended Systems XTNDAccess ESI-9685

         Note that there is another USB driver for those devices called ir-usb
         which is NOT compatible with the IrDA stack and conflict  with  irda-
         usb.  Because  it  always  loads  first,  you  have  to remove ir-usb

         Devices based on the SigmaTel chip are not  not  compliant  with  the
         IrDA-USB  class  specification  and  therfore  not  supported by this

       · nsc-ircc NSC IrDA device driver (options: io,  irq,  dma,  dongle_id,
         qos_mtt_bits).  This chipset is used by e.g.:

         IBM ThinkPad  dongle_id=0x09

         HP OmniBook 6000 dongle_id=0x08

       · sa1100_ir  Infrared  driver for devices based on the StrongARM SA1100
         embedded microprocessor (options: power_level, tx_lpm).  This  driver
         may  support  FIR on devices that can do it.  This chipset is used by

         Samsung YOPY, COMPAQ iPAQ, SHARP Zaurus SL5000/5500

       · smc-ircc SMC IrCC controller driver  (options:  ircc_dma,  ircc_irq).
         This chipset is used by e.g.:

         Fujitsu-Siemens Lifebook 635t Sony PCG-505TX

       · w83977af_ir  Winbond  W83977AF  IrDA device driver (options: io, irq,
         qos_mtt_bits).  This chipset is used by e.g.:

         Corel NetWinder

       · toshoboe Toshiba OBOE IrDA device driver, supports Toshiba Type-O  IR
         chipset.  (options: max_baud).  This chipset is used by e.g.:

         Toshiba Libretto 100CT., and many more old Toshiba laptops.

       · donauboe  is a new version of toshoboe and has better FIR support and
         compability  with  the   Donauoboe   chip
         irda.html (options: ..).  This chipset is used by e.g.:

         Toshiba  Libretto  100CT.,  Tecra  8100,  Portege  7020 and many more
         Toshiba laptops.

       · vlsi_ir VLSI 82C147 SIR/MIR/FIR device driver This chipset is used by

         HP Omnibook 800

         (options: ..).

         · clksrc int, description "clock input source selection"

         · ringsize  int  array  (min  = 1, max = 2), description "tx, rx ring
           descriptor size"

         · sirpulse int, description "sir pulse width tuning"

         · mtt_bits int, description "IrLAP  bitfield  representing  min-turn-


       Attach  the  IrDA stack to the second serial port (integrated IrDA port
       using serial emulation) and start discovery:

       · irattach /dev/ttyS1 -s

       Attach the IrDA stack to the  first  serial  port  where  you  have  an
       external ACTiSYS serial dongle and start discovery:

       · irattach /dev/ttyS0 -d actisys+ -s

       Attach the IrDA stack to the first IrDA-USB dongle and start discovery:

       · modprobe irda-usb ; irattach irda0 -s

       Attach  the  IrDA  stack  to  the  NSC  FIR  (4Mbps) device driver on a
       Thinkpad laptop:

       · modprobe nsc-ircc dongle_id=0x9 ; irattach irda0 -s.

       Attach the IrDA stack to  the  NSC  FIR  (4Mbps)  device  driver  on  a
       Thinkpad laptop:

       · irattach irda0 -s.

         This   assume   that   you   have  added  the  following  entries  to

         options nsc-ircc dongle_id=0x09

         alias irda0 nsc-ircc


       The  following  hints  are  a  very   short   introduction   into   the
       configuration  of Linux/IrDA. If this doesn't help read the Linux/IrDA-
       Tutorial and/or the Infrared-HOWTO  .   Before  configuring  Linux/IrDA
       make sure whether you want to configure SIR or FIR. It's recommended to
       try SIR first, unless your device  is  not  compatible  with  SIR  (for
       example USB dongles).

       To  get  the  SIR  "serial"  device have a look into the BIOS. Then run
       dmesg | grep tty to get a survey  of  tty  devices  supported  by  your
       machine.  Now  try to choose the one, which is probably the IrDA device
       and use irattach /dev/ttySx -s.

       If you don't succeed with SIR (which seems a rare  case)  you  may  try
       FIR. First look up the BIOS. Then run findchip to get information about
       the IrDA controller chip. Use setserial /dev/ttySx uart none  to  avoid
       conflicts  with  the  serial  driver.  Note: don't use setserial if you
       configure SIR.  Now you may use irattach.

       Finally irdadump should show at  least  your  computer  itself.  If  it
       doesn't start at the beginning.

       This  man  page  deal  only  with the low level of the IrDA stack (IrDA
       ports and IrDA drivers). After this step is done, you usually  need  to
       setup  your  favorite  application  to access the high level IrDA stack
       (via IrCOMM, IrLPT,  IrNET,  IrLAN  or  IrSOCK),  which  is  documented

       This  man  page  doesn't  document  the usage of the irport driver. The
       irport driver support the same hardware as the  irtty  driver,  but  is
       configured like a FIR driver.


       This section currently contains the raw error messages from source code

       "ioctl(TIOCGETD): %m"

       "irattach: tty: set_disc(%d): %s"

       "tcsetattr: %m"

       "Failed to open %s: %m"

       "Couldn't get device fd flags: %m"

       "Couldn't set device to non-blocking mode: %m"




       irattach(8),  irdaping(8),   irdadump(8),   findchip(8),   irpsion5(8),

       Linux/IrDA  Project -*- Linux/IrDA-Tutorial      -*-
       Infrared-HOWTO  -*- Infrared-Hardware-


       This manual page is written by Werner Heuser <>. It is
       based  on the READMEs from irda-utils by the Linux/IrDA Project and the
       Linux/IrDA-Tutorial.  It was subsequently updated and modified by  Jean
       Tourrilhes <>.


       Copyright (c) 2001 Werner Heuser Copyright (c) 2002 Jean Tourrilhes

       Permission  is  granted to copy, distribute and/or modify this document
       under the terms of the GNU Free Documentation License  (GFDL),  Version
       1.1  or  any  later  version published by the Free Software Foundation;
       with no Invariant Sections, no  Front-Cover  Texts  and  no  Back-Cover

                                 03 July 2006                      IRATTACH(8)