Provided by: lldpad_0.9.43+git20111215.c0498b-1_amd64
lldptool - manage the LLDP settings and status of lldpad
lldptool <command> [options] [argument]
lldptool is used to query and configure lldpad. It connects to the client interface of lldpad to perform these operations. lldptool will operate in interactive mode if it is executed without a command. In interactive mode, lldptool also functions as an event listener and will print out events as they are received asynchronously from lldpad.
-i [ifname] specifies the network interface to which the command applies -V [tlvid] specifies the TLV identifier The tlvid is an integer value used to identify specific LLDP TLVs. The tlvid value is the Type value for types not equal to 127 (the organizationally specific type). For organizationally specific TLVs, the tlvid is the value represented by the 3 byte OUI and 1 byte subtype - where the subtype is the lowest order byte of the tlvid. The tlvid can be entered as a numerical value (e.g. 10 or 0xa), or for supported TLVs, as a keyword. Review the lldptool help output to see the list of supported TLV keywords. -n "neighbor" option for commands which can use it (e.g. get-tlv) -g [bridge scope] specify the bridge scope this command operates on. Allows to set and query all LLDP TLV modules for "nearest_bridge" (short: "nb"), "nearest_customer_bridge" ("ncb") and "nearest_nontpmr_bridge" ("nntpmrb") group mac addresses. Configurations are saved into independent sections in lldpad.conf. If no bridge scope is supplied this default to "nearest bridge" to preserve the previous behaviour. -c <argument list> "config" option for TLV queries. Indicates that the query is for the configuration elements for the specified TLV. The argument list specifies the specific elements to query. If no arguments are listed, then all configuration elements for the TLV are returned. -r show raw client interface messages -R show only raw Client interface messages
license show license information -h, help show usage information -v, version show version information -S, stats get LLDP statistics -t, get-tlv get TLV information -T, set-tlv set TLV information -l, get-lldp get LLDP parameters -L, set-lldp set LLDP parameters -q, quit exit from interactive mode
adminStatus Argument for the get-lldp/set-lldp commands. May be applied per port or globbally. Valid values are: disabled, rx, tx, rxtx enableTx Argument for the get-tlv/set-tlv commands. May be applied per port for a specified TLV. Valid values are: yes, no. If the DCBX TLV enableTx is set to no, then all of the DCB feature TLVs DCBX advertise settings will be turned off as well. Setting enableTx to yes for a DCBX TLV will not affect the DCBX advertise settings. ipv4 Argument for the get-tlv/set-tlv commands with respect to the Management Address TLV. May be applied per port or globally. The get command will retrieve the configured value. Set values take the form of an IPv4 address: A.B.C.D ipv6 Argument for the get-tlv/set-tlv commands with respect to the Management Address TLV. May be applied per port or globally. The get command will retrieve the configured value. Set values take the form of an IPv6 address: 1111:2222:3333:4444:5555:6666:7777:8888 and various shorthand variations.
Configure LLDP adminStatus to Receive and Transmit for interface eth2 lldptool -L -i eth2 adminStatus=rxtx lldptool set-lldp -i eth2 adminStatus=rxtx Disable the LLDP adminStatus for all interfaces lldptool set-lldp adminStatus=disabled Query the LLDP adminStatus for interface eth3 lldptool -l -i eth3 adminStatus lldptool get-lldp -i eth3 adminStatus Query the LLDP statistics for interface eth3 lldptool -S -i eth3 adminStatus lldptool stats -i eth3 adminStatus Query the local TLVs which are being transmitted for a given interface: lldptool -t -i eth3 lldptool get-tlv -i eth3 Query the received neighbor TLVs received on a given interface: lldptool -t -n -i eth3 lldptool get-tlv -n -i eth3 Query the value of the System Description TLV as received from the neighbor on a given interface: lldptool -t -n -i eth3 -V sysDesc lldptool get-tlv -n -i eth3 -V 6 Disable transmit of the IEEE 802.3 MAC/PHY Configuration Status TLV for a given interface: lldptool -T -i eth3 -V macPhyCfg enableTx=no lldptool set-tlv -i eth3 -V 0x120f01 enableTx=no Enable transmit of the Port Description TLV for all interfaces: lldptool -T -V portDesc enableTx=yes lldptool set-tlv -V 4 enableTx=yes Query value of the transmit setting for the Port Description TLV for a given interface: lldptool -t -V portDesc -c enableTx lldptool get-tlv -V 4 -c enableTx Set a Management Address TLV on eth3 to carry IPv4 address 192.168.10.10 lldptool -T -i eth3 -V mngAddr ipv4=192.168.10.10 Set a Management Address TLV on eth3 to carry IPv6 address ::192.168.10.10 lldptool -T -i eth3 -V mngAddr ipv6=::192.168.10.10 Get the configured IPv4 address for the Management Address TLV on eth3 lldptool -t -i eth3 -V mngAddr -c ipv4 Get all configured attributes for the Management Address TLV on eth3 lldptool -t -i eth3 -V mngAddr -c Query the current DCBX mode that will be used if lldpad is restarted. (this is not a persistent setting) lldptool -t -i eth3 -V IEEE-DCBX -c mode Reset the DCBX mode to be 'auto' (start in IEEE DCBX mode) after the next lldpad restart lldptool -T -i eth3 -V IEEE-DCBX mode=reset Enable transmit of the Edge Virtual Bridging TLV for interface eth4 lldptool -i eth4 -T -V evbCfg enableTx=yes Configure EVB TLV to set reflective relay and RTE,ECP and VDP capabilities lldptool -T -i eth4 -V evbCfg fmode=reflectiverelay lldptool -T -i eth4 -V evbCfg capabilities=rte,ecp,vdp Enable transmit of the VDP for interface eth4 lldptool -i eth4 -T -V vdp enableTx=yes Configurations per port have higher precedence than global configurations.
lldptool-ets(8), lldptool-pfc(8), lldptool-app(8), lldptool-med(8), dcbtool(8), lldpad(8)
lldptool - LLDP agent configuration utility Copyright(c) 2007-2010 Intel Corporation. Portions of lldptool are based on: hostapd-0.5.7 Copyright (c) 2004-2008, Jouni Malinen <firstname.lastname@example.org>
This program is free software; you can redistribute it and/or modify it under the terms and conditions of the GNU General Public License, version 2, as published by the Free Software Foundation. This program is distributed in the hope it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. The full GNU General Public License is included in this distribution in the file called "COPYING".
Contact Information: open-lldp Mailing List <email@example.com> November 2, 2011 lldptool(8)