Provided by: fastforward_0.51-3_amd64
setforward - create a forwarding database
setforward cdb tmp
setforward reads a table of forwarding instructions from its standard input. It converts the table into a forwarding database. The forwarding database can be used by fastforward. setforward writes the forwarding database to tmp; it then moves tmp to cdb. tmp and cdb must be on the same filesystem. If there is a problem creating tmp, setforward complains and leaves cdb alone. The forwarding database format is portable across machines.
A forwarding instruction contains a target, a colon, a series of commands, and a semicolon. Each command is a recipient address, owner address, external mailing list, or program. Commands are separated by commas. For example, firstname.lastname@example.org: email@example.com, firstname.lastname@example.org; says that mail for email@example.com should be forwarded to the recipient addresses firstname.lastname@example.org and email@example.com. When setforward sees # it ignores all text from # to the end of the line: # this is a comment setforward ignores all other line endings, so you can split a forwarding instruction across lines. It also ignores spaces and tabs. Exception: you can put a space (or tab or comma or whatever) into a target or command by putting a backslash in front of it. (However, NUL bytes are not permitted anywhere.)
When fastforward sees the incoming address firstname.lastname@example.org, it tries three targets: email@example.com, @host.dom, and user@. It obeys the commands for the first target that it finds. Target names are interpreted without regard to case. All the commands for a single target must be listed in a single instruction. Exception: an owner address can be listed in a separate instruction.
If a command begins with an ampersand, setforward takes the remaining bytes in the command as a recipient address: firstname.lastname@example.org: &email@example.com; fastforward sends each incoming mail message to the recipient address. The recipient address must include a fully qualified domain name. It cannot be longer than 800 bytes. If a recipient address is itself a target in the forwarding table, fastforward will recursively handle the instructions for that target. Note that @host.dom and user@ wildcards do not apply here; they apply only to the incoming address. If a command begins with a letter or number, setforward takes the entire command as a recipient address: firstname.lastname@example.org: email@example.com;
If a command begins with a question mark, setforward takes the remaining bytes in the command as an owner address: firstname.lastname@example.org: ?email@example.com; fastforward uses that address as the envelope sender for forwarded mail, so bounces will go back to that address. (Normally, if a message is forwarded to a bad address, it will bounce back to the original envelope sender.)
EXTERNAL MAILING LISTS
If a command begins with a dot or slash, setforward takes the entire command as the name of a binary mailing list file created by setmaillist: firstname.lastname@example.org: /etc/lists/sos.bin; fastforward will read and obey the commands in that file. The file must be world-readable and accessible to fastforward.
If a command begins with a vertical bar or exclamation point, setforward takes the rest of the command as the name of a program to run: dew@: |dew-monitor; For a vertical bar, fastforward feeds the message to that program. An exclamation point works the same way except that fastforward inserts $UFLINE, $RPLINE, and $DTLINE in front of the message.
When fastforward is building the recipient list for a message, it keeps track of the recipient addresses and external mailing lists it has used. If the same command shows up again, it skips it. For example: email@example.com: firstname.lastname@example.org, email@example.com; firstname.lastname@example.org: email@example.com, firstname.lastname@example.org; email@example.com: firstname.lastname@example.org, email@example.com; A message to firstname.lastname@example.org will be sent to email@example.com only once. (This also means that addresses in an internal forwarding loop are discarded.) Exception: If a target has an owner address, commands for that target are considered different from commands for ``outside'' targets.
newaliases(1), preline(1), printforward(1), setmaillist(1) setforward(1)