Ubuntu Manpage: racoon.conf — configuration file for racoon

Provided by: racoon_0.8.0-14+deb7u1ubuntu0.1_amd64

NAME

     racoon.conf — configuration file for racoon

DESCRIPTION

racoon.conf is the configuration file for the racoon(8) ISAKMP daemon. racoon(8) negotiates
security associations for itself (ISAKMP SA, or phase 1 SA) and for kernel IPsec (IPsec SA,
or phase 2 SA). The file consists of a sequence of directives and statements. Each
directive is composed by a tag and statements, enclosed by ‘{’ and ‘}’. Lines beginning
with ‘#’ are comments.

Meta Syntax
Keywords and special characters that the parser expects exactly are displayed using this
font. Parameters are specified with this font. Square brackets (‘[’ and ‘]’) are used to
show optional keywords and parameters. Note that you have to pay attention when this manual
is describing port numbers. The port number is always enclosed by ‘[’ and ‘]’. In this
case, the port number is not an optional keyword. If it is possible to omit the port
number, the expression becomes [[port]]. The vertical bar (‘|’) is used to indicate a
choice between optional parameters. Parentheses (‘(’ and ‘)’) are used to group keywords
and parameters when necessary. Major parameters are listed below.

number means a hexadecimal or a decimal number. The former must be prefixed with ‘0x’.
string
path
file means any string enclosed in ‘"’ (double quotes).
address means IPv6 and/or IPv4 address.
port means a TCP/UDP port number. The port number is always enclosed by ‘[’ and ‘]’.
timeunit is one of following: sec, secs, second, seconds, min, mins, minute, minutes, hour,
hours.

Privilege separation
privsep { statements }
Specifies privilege separation parameters. When enabled, these enable racoon(8) to
operate with an unprivileged instance doing most of the work, while a privileged
instance takes care of performing the following operations as root: reading PSK and
private keys, launching hook scripts, and validating passwords against system
databases or against PAM. Please note that using privilege separation makes changes
to the listen and paths sections ignored upon configuration reloads. A racoon(8)
restart is required if you want such changes to be taken into account.

user user;
The user to which the unprivileged instance of racoon(8), should switch.
This can be a quoted user name or a numeric UID.
group group;
The group the unprivileged instance of racoon(8), should switch. This can
be a quoted group name or a numeric GID.
chroot path;
A directory to which the unprivileged instance of racoon(8) should
chroot(2). This directory should hold a tree where the following files must
be reachable:
/dev/random
/dev/urandom
The certificates
The file containing the Xauth banner

The PSK file, the private keys, and the hook scripts are accessed through
the privileged instance of racoon(8) and do not need to be reachable in the
chroot(2)'ed tree.

Path Specification
This section specifies various paths used by racoon. When running in privilege separation
mode, certificate and script paths are mandatory. A racoon(8) restart is required if you
want path changes to be taken into account.
path include path;
Specifies a path to include a file. See File Inclusion.
path pre_shared_key file;
Specifies a file containing pre-shared key(s) for various ID(s). See Pre-shared key
File.
path certificate path;
racoon(8) will search this directory if a certificate or certificate request is
received. If you run with privilege separation, racoon(8) will refuse to use a
certificate stored outside of this directory.
path backupsa file;
Specifies a file to which SA information negotiated by racoon should be stored.
racoon(8) will install SA(s) from the file when started with the -B flag. The file
is growing because racoon(8) simply adds SAs to it. You should maintain the file
manually.
path script path;
racoon(8) will search this directory for scripts hooks. If you run with privilege
separation, racoon(8) will refuse to execute a script stored outside of this
directory.
path pidfile file;
Specifies file where to store PID of process. If path starts with / it is treated
as an absolute path. Otherwise, it is treated as a relative path to the VARRUN
directory specified at compilation time. Default is racoon.pid.

File Inclusion
include file
Specifies other configuration files to be included.

Timer Specification
timer { statements }
This section specifies various timer values used by racoon.

counter number;
The maximum number of retries to send. The default is 5.
interval number timeunit;
The interval to resend, in seconds. The default time is 10 seconds.
persend number;
The number of packets per send. The default is 1.
phase1 number timeunit;
The maximum time it should take to complete phase 1. The default time is 15
seconds.
phase2 number timeunit;
The maximum time it should take to complete phase 2. The default time is 10
seconds.
natt_keepalive number timeunit;
The interval between sending NAT-Traversal keep-alive packets. The default
time is 20 seconds. Set to 0s to disable keep-alive packets.

Listening Port Specification
listen { statements }
If no listen directive is specified, racoon(8) will listen on all available
interface addresses. The following is the list of valid statements:

isakmp address [[port]];
If this is specified, racoon(8) will only listen on the defined address.
The default port is 500, which is specified by IANA. You can provide more
than one address definition.
isakmp_natt address [port];
Same as isakmp but also sets the socket options to accept UDP-encapsulated
ESP traffic for NAT-Traversal. If you plan to use NAT-T, you should provide
at least one address with port 4500, which is specified by IANA. There is
no default.
strict_address;
Requires that all addresses for ISAKMP be bound. This statement will be
ignored if you do not specify address definitions.
When running in privilege separation mode, you need to restart racoon(8) to have
changes to the listen section taken into account.

The listen section can also be used to specify the admin socket mode and ownership
if racoon was built with support for admin port.
adminsock path [owner group mode];
The path, owner, and group values specify the socket path, owner, and group.
They must be quoted. The defaults are /var/racoon/racoon.sock, UID 0, and
GID 0. mode is the access mode in octal. The default is 0600.
adminsock disabled;
This directive tells racoon to not listen on the admin socket.

Miscellaneous Global Parameters
gss_id_enc enctype;
Older versions of racoon(8) used ISO-Latin-1 as the encoding of the GSS-API
identifier attribute. For interoperability with Microsoft Windows' GSS-API
authentication scheme, the default encoding has been changed to UTF-16LE. The
gss_id_enc parameter allows racoon(8) to be configured to use the old encoding for
compatibility with existing racoon(8) installations. The following are valid values
for enctype:

utf-16le
Use UTF-16LE to encode the GSS-API identifier attribute. This is the
default encoding. This encoding is compatible with Microsoft Windows.
latin1 Use ISO-Latin-1 to encode the GSS-API identifier attribute. This is the
encoding used by older versions of racoon(8).

pfkey_buffer kBytes
Specifies the socket send/receive buffer size in kilobytes. Numerous kernel PF_KEY
implementations have problems with dumping SAD/SDP with large amount of entries
(this happens when 100s to 1000s of tunnels are configured).

The default value of 0 leaves everything at the OS-specific default value. If the
default buffer size is greater than what is specified here racoon will not decrease
it.

This problem is known to be fixed in Linux 2.6.25 and later.

Remote Nodes Specifications
remote name [inherit parent_name] { statements }
Specifies the IKE phase 1 parameters for each remote node.

If connection is initiated using racoonctl, a unique match using the remote IP must
be found or the remote block name has to be given. For received acquires (kernel
notices traffic requiring a new SA) the remote IP and remoteid from matching sainfo
block are used to decide the remoteblock. If no uniquely matching remoteblock is
found using these criteria, no connection attempt is done.

When acting as responder, racoon picks the first proposal that has one or more
acceptable remote configurations. When determining if a remote specification is
matching the following information is checked:
• The remote IP is checked against remote_address.
• ISAKMP exchange type is checked against exchange_mode.
• ISAKMP SA attributes must match a proposal block.
• The remote identity is matched against peers_identifier if verify_identifier
is on.
• If a certificate request was received, it must match the issuer of
certificate_type x509 certificate. If certificate request without issuer
name was sent, the match_empty_cr parameter specifies whether or not remote
block matches.

Similarly, NAT-T is enabled if any of the initial remote configuration candidates
allow NAT-T.

Sections with inherit parent statements (where parent is either address or a keyword
anonymous) that have all values predefined to those of a given parent. In these
sections it is enough to redefine only the changed parameters.

The following are valid statements.

remote_address address;
Defines the IP address of the peer.
exchange_mode (main | aggressive | base);
Defines the exchange mode for phase 1 when racoon is the initiator. It also
means the acceptable exchange mode when racoon is the responder. More than
one mode can be specified by separating them with a comma. All of the modes
are acceptable. The first exchange mode is what racoon uses when it is the
initiator.
doi ipsec_doi;
Means to use IPsec DOI as specified in RFC 2407. You can omit this
statement.
situation identity_only;
Means to use SIT_IDENTITY_ONLY as specified in RFC 2407. You can omit this
statement.
my_identifier [qualifier] idtype ...;
Specifies the identifier sent to the remote host and the type to use in the
phase 1 negotiation. address, fqdn, user_fqdn, keyid, and asn1dn can be
used as an idtype. The qualifier is currently only used for keyid, and can
be either file or tag. The possible values are :
my_identifier address [address];
The type is the IP address. This is the default type if you do not
specify an identifier to use.
my_identifier user_fqdn string;
The type is a USER_FQDN (user fully-qualified domain name).
my_identifier fqdn string;
The type is a FQDN (fully-qualified domain name).
my_identifier keyid [file] file;
The type is a KEY_ID, read from the file.
my_identifier keyid tag string;
The type is a KEY_ID, specified in the quoted string.
my_identifier asn1dn [string];
The type is an ASN.1 distinguished name. If string is omitted,
racoon(8) will get the DN from the Subject field in the certificate.
xauth_login [string];
Specifies the login to use in client-side Hybrid authentication. It is
available only if racoon(8) has been built with this option. The associated
password is looked up in the pre-shared key files, using the login string as
the key id.
peers_identifier idtype ...;
Specifies the peer's identifier to be received. If it is not defined then
racoon(8) will not verify the peer's identifier in ID payload transmitted
from the peer. If it is defined, the behavior of the verification depends
on the flag of verify_identifier. The usage of idtype is the same as
my_identifier except that the individual component values of an asn1dn
identifier may specified as * to match any value (e.g. "C=XX, O=MyOrg, OU=*,
CN=Mine"). The format of the specification should correspond to RFC 2253;
in particular, commas and certain other characters - ,=+<>#; - may be
included in a name by preceding them with a backslash "\", and arbitrary
characters may be inserted in a name with the "\nn" escape, where nn is the
hex representation of the ascii value of the desired character. Alternative
acceptable peer identifiers may be specified by repeating the
peers_identifier statement.
verify_identifier (on | off);
If you want to verify the peer's identifier, set this to on. In this case,
if the value defined by peers_identifier is not the same as the peer's
identifier in the ID payload, the negotiation will fail. The default is
off.
certificate_type certspec;
Specifies a certificate specification. certspec is one of followings:
x509 certfile privkeyfile;
certfile means a file name of a certificate. privkeyfile means a
file name of a secret key.
plain_rsa privkeyfile;
privkeyfile means a file name of a private key generated by
plainrsa-gen(8). Required for RSA authentication.
ca_type cacertspec;
Specifies a root certificate authority specification. cacertspec is one of
followings:
x509 cacertfile;
cacertfile means a file name of the root certificate authority.
Default is /etc/openssl/cert.pem
mode_cfg (on | off);
Gather network information through ISAKMP mode configuration. Default is
off.
weak_phase1_check (on | off);
Tells racoon to act on unencrypted deletion messages during phase 1. This
is a small security risk, so the default is off, meaning that racoon will
keep on trying to establish a connection even if the user credentials are
wrong, for instance.
peers_certfile (dnssec | certfile | plain_rsa pubkeyfile);
If dnssec is defined, racoon(8) will ignore the CERT payload from the peer,
and try to get the peer's certificate from DNS instead. If certfile is
defined, racoon(8) will ignore the CERT payload from the peer, and will use
this certificate as the peer's certificate. If plain_rsa is defined,
racoon(8) will expect pubkeyfile to be the peer's public key that was
generated by plainrsa-gen(8).
script script phase1_up
script script phase1_down
script script phase1_dead
Shell scripts that get executed when a phase 1 SA goes up or down, or when
it is detected as dead by DPD. All scripts get either phase1_up ,
phase1_down or phase1_dead as first argument, and the following variables
are set in their environment:
LOCAL_ADDR
The local address of the phase 1 SA.
LOCAL_PORT
The local port used for IKE for the phase 1 SA.
REMOTE_ADDR
The remote address of the phase 1 SA.
REMOTE_PORT
The remote port used for IKE for the phase 1 SA.
REMOTE_ID
The remote identity received in IKE for the phase 1 SA.
The following variables are only set if mode_cfg was enabled:
INTERNAL_ADDR4
An IPv4 internal address obtained by ISAKMP mode config.
INTERNAL_NETMASK4
An IPv4 internal netmask obtained by ISAKMP mode config.
INTERNAL_CIDR4
An IPv4 internal netmask obtained by ISAKMP mode config, in CIDR
notation.
INTERNAL_DNS4
The first internal DNS server IPv4 address obtained by ISAKMP mode
config.
INTERNAL_DNS4_LIST
A list of internal DNS servers IPv4 address obtained by ISAKMP mode
config, separated by spaces.
INTERNAL_WINS4
The first internal WINS server IPv4 address obtained by ISAKMP mode
config.
INTERNAL_WINS4_LIST
A list of internal WINS servers IPv4 address obtained by ISAKMP mode
config, separated by spaces.
SPLIT_INCLUDE
The space separated list of IPv4 addresses and masks (address slash
mask) that define the networks to be encrypted (as opposed to the
default where all the traffic should be encrypted) ; obtained by
ISAKMP mode config ; SPLIT_INCLUDE and SPLIT_LOCAL are mutually
exclusive.
SPLIT_LOCAL
The space separated list of IPv4 addresses and masks (address slash
mask) that define the networks to be considered local, and thus
excluded from the tunnels ; obtained by ISAKMP mode config.
SPLIT_INCLUDE_CIDR
Same as SPLIT_INCLUDE, with netmasks in CIDR notation.
SPLIT_LOCAL_CIDR
Same as SPLIT_LOCAL, with netmasks in CIDR notation.
DEFAULT_DOMAIN
The DNS default domain name obtained by ISAKMP mode config.
send_cert (on | off);
If you do not want to send a certificate, set this to off. The default is
on.
send_cr (on | off);
If you do not want to send a certificate request, set this to off. The
default is on.
match_empty_cr (on | off);
Specifies whether this remote block is a valid match when a non-specific
certificate request is received. The default is on.
verify_cert (on | off);
By default, the identifier sent by the remote host (as specified in its
my_identifier statement) is compared with the credentials in the certificate
used to authenticate the remote host as follows:
Type asn1dn:
The entire certificate subject name is compared with the identifier,
e.g. "C=XX, O=YY, ...".
Type address, fqdn, or user_fqdn:
The certificate's subjectAltName is compared with the identifier.
If the two do not match the negotiation will fail. If you do not want to
verify the identifier using the peer's certificate, set this to off.
lifetime time number timeunit;
Define a lifetime of a certain time which will be proposed in the phase 1
negotiations. Any proposal will be accepted, and the attribute(s) will not
be proposed to the peer if you do not specify it (them). They can be
individually specified in each proposal.
ike_frag (on | off | force);
Enable receiver-side IKE fragmentation if racoon(8) has been built with this
feature. If set to on, racoon will advertise itself as being capable of
receiving packets split by IKE fragmentation. This extension is there to
work around broken firewalls that do not work with fragmented UDP packets.
IKE fragmentation is always enabled on the sender-side, and it is used if
the peer advertises itself as IKE fragmentation capable. By selecting
force, IKE Fragmentation will be used when racoon is acting as the initiator
even before the remote peer has advertised itself as IKE fragmentation
capable.
esp_frag fraglen;
This option is only relevant if you use NAT traversal in tunnel mode. Its
purpose is to work around broken DSL routers that reject UDP fragments, by
fragmenting the IP packets before ESP encapsulation. The result is ESP over
UDP of fragmented packets instead of fragmented ESP over UDP packets (i.e.,
IP:UDP:ESP:frag(IP) instead of frag(IP:UDP:ESP:IP)). fraglen is the maximum
size of the fragments. 552 should work anywhere, but the higher fraglen is,
the better the performance.

Note that because PMTU discovery is broken on many sites, you will have to
use MSS clamping if you want TCP to work correctly.
initial_contact (on | off);
Enable this to send an INITIAL-CONTACT message. The default value is on.
This message is useful only when the responder implementation chooses an old
SA when there are multiple SAs with different established time and the
initiator reboots. If racoon did not send the message, the responder would
use an old SA even when a new SA was established. For systems that use a
KAME derived IPSEC stack, the sysctl(8) variable net.key.preferred_oldsa can
be used to control this preference. When the value is zero, the stack
always uses a new SA.
passive (on | off);
If you do not want to initiate the negotiation, set this to on. The default
value is off. It is useful for a server.
proposal_check level;
Specifies the action of lifetime length, key length, and PFS of the phase 2
selection on the responder side, and the action of lifetime check in phase
1. The default level is strict. If the level is:
obey The responder will obey the initiator anytime.
strict If the responder's lifetime length is longer than the initiator's or
the responder's key length is shorter than the initiator's, the
responder will use the initiator's value. Otherwise, the proposal
will be rejected. If PFS is not required by the responder, the
responder will obey the proposal. If PFS is required by both sides
and the responder's group is not equal to the initiator's, then the
responder will reject the proposal.
claim If the responder's lifetime length is longer than the initiator's or
the responder's key length is shorter than the initiator's, the
responder will use the initiator's value. If the responder's
lifetime length is shorter than the initiator's, the responder uses
its own length AND sends a RESPONDER-LIFETIME notify message to an
initiator in the case of lifetime (phase 2 only). For PFS, this
directive behaves the same as strict.
exact If the initiator's lifetime or key length is not equal to the
responder's, the responder will reject the proposal. If PFS is
required by both sides and the responder's group is not equal to the
initiator's, then the responder will reject the proposal.
support_proxy (on | off);
If this value is set to on, then both values of ID payloads in the phase 2
exchange are always used as the addresses of end-point of IPsec-SAs. The
default is off.
generate_policy (on | off | require | unique);
This directive is for the responder. Therefore you should set passive to on
in order that racoon(8) only becomes a responder. If the responder does not
have any policy in SPD during phase 2 negotiation, and the directive is set
to on, then racoon(8) will choose the first proposal in the SA payload from
the initiator, and generate policy entries from the proposal. It is useful
to negotiate with clients whose IP address is allocated dynamically. Note
that an inappropriate policy might be installed into the responder's SPD by
the initiator, so other communications might fail if such policies are
installed due to a policy mismatch between the initiator and the responder.
on and require values mean the same thing (generate a require policy).
unique tells racoon to set up unique policies, with a monotoning increasing
reqid number (between 1 and IPSEC_MANUAL_REQID_MAX). This directive is
ignored in the initiator case. The default value is off.
nat_traversal (on | off | force);
This directive enables use of the NAT-Traversal IPsec extension (NAT-T).
NAT-T allows one or both peers to reside behind a NAT gateway (i.e., doing
address- or port-translation). If a NAT gateway is detected during the
phase 1 handshake, racoon will attempt to negotiate the use of NAT-T with
the remote peer. If the negotiation succeeds, all ESP and AH packets for
the given connection will be encapsulated into UDP datagrams (port 4500, by
default). Possible values are:
on NAT-T is used when a NAT gateway is detected between the peers.
off NAT-T is not proposed/accepted. This is the default.
force NAT-T is used regardless of whether a NAT gateway is detected
between the peers or not.
Please note that NAT-T support is a compile-time option. Although it is
enabled in the source distribution by default, it may not be available in
your particular build. In that case you will get a warning when using any
NAT-T related config options.
dpd_delay delay;
This option activates the DPD and sets the time (in seconds) allowed between
2 proof of liveliness requests. The default value is 0, which disables DPD
monitoring, but still negotiates DPD support.
dpd_retry delay;
If dpd_delay is set, this sets the delay (in seconds) to wait for a proof of
liveliness before considering it as failed and send another request. The
default value is 5.
dpd_maxfail number;
If dpd_delay is set, this sets the maximum number of liveliness proofs to
request (without reply) before considering the peer is dead. The default
value is 5.
rekey (on | off | force);
Enable automatic renegotiation of expired phase1 when there are non-dying
phase2 SAs. Possible values are:
force Rekeying is done unconditionally.
on Rekeying is done only if DPD monitoring is active. This is the
default.
off No automatic rekeying. Do note that turning off automatic rekeying
will result in inaccurate DPD monitoring.
nonce_size number;
define the byte size of nonce value. Racoon can send any value although
RFC2409 specifies that the value MUST be between 8 and 256 bytes. The
default size is 16 bytes.
ph1id number;
An optional number to identify the remote proposal and to link it only with
sainfos who have the same number. Defaults to 0.
proposal { sub-substatements }
encryption_algorithm algorithm;
Specifies the encryption algorithm used for the phase 1 negotiation.
This directive must be defined. algorithm is one of following: des,
3des, blowfish, cast128, aes, camellia for Oakley. For other
transforms, this statement should not be used.
hash_algorithm algorithm;
Defines the hash algorithm used for the phase 1 negotiation. This
directive must be defined. algorithm is one of following: md5,
sha1, sha256, sha384, sha512 for Oakley.
authentication_method type;
Defines the authentication method used for the phase 1 negotiation.
This directive must be defined. type is one of: pre_shared_key,
rsasig (for plain RSA authentication), gssapi_krb,
hybrid_rsa_server, hybrid_rsa_client, xauth_rsa_server,
xauth_rsa_client, xauth_psk_server or xauth_psk_client.
dh_group group;
Defines the group used for the Diffie-Hellman exponentiations. This
directive must be defined. group is one of following: modp768,
modp1024, modp1536, modp2048, modp3072, modp4096, modp6144,
modp8192. Or you can define 1, 2, 5, 14, 15, 16, 17, or 18 as the
DH group number. When you want to use aggressive mode, you must
define the same DH group in each proposal.
lifetime time number timeunit;
Defines the lifetime of the phase 1 SA proposal. Refer to the
description of the lifetime directive defined in the remote
directive.
gss_id string;
Defines the GSS-API endpoint name, to be included as an attribute in
the SA, if the gssapi_krb authentication method is used. If this is
not defined, the default value of ‘host/hostname’ is used, where
hostname is the value returned by the hostname(1) command.

remote (address | anonymous) [[port]] [inherit parent] { statements }
Deprecated format of specifying a remote block. This will be removed in future. It
is a remnant from time when remote block was decided solely based on the peers IP
address.

This is equivalent to:

remote "address" [inherit "parent-address"] {
remote_address address;
}

Sainfo Specifications
sainfo (local_id | anonymous) (remote_id | clientaddr | anonymous) [from idtype [string]]
[group string] { statements }
Defines the parameters of the IKE phase 2 (IPsec-SA establishment).

The local_id and remote_id strings are constructed like:

address address [/ prefix] [[port]] ul_proto

subnet address [/ prefix] [[port]] ul_proto

An id string should be expressed to match the exact value of an ID payload. This is
not like a filter rule. For example, if you define 3ffe:501:4819::/48 as local_id.
3ffe:501:4819:1000:/64 will not match. In the case of a longest prefix (selecting a
single host), address instructs to send ID type of ADDRESS while subnet instructs to
send ID type of SUBNET. Otherwise, these instructions are identical.

The anonymous keyword can be used to match any id. The clientaddr keyword can be
used to match a remote id that is equal to either the peer ip address or the
mode_cfg ip address (if assigned). This can be useful to restrict policy generation
when racoon is acting as a client gateway for peers with dynamic ip addresses.

The from keyword allows an sainfo to only match for peers that use a specific phase1
id value during authentication. The group keyword allows an XAuth group membership
check to be performed for this sainfo section. When the mode_cfg auth source is set
to system or ldap, the XAuth user is verified to be a member of the specified group
before allowing a matching SA to be negotiated.

pfs_group group;
define the group of Diffie-Hellman exponentiations. If you do not require
PFS then you can omit this directive. Any proposal will be accepted if you
do not specify one. group is one of following: modp768, modp1024, modp1536,
modp2048, modp3072, modp4096, modp6144, modp8192. Or you can define 1, 2,
5, 14, 15, 16, 17, or 18 as the DH group number.
lifetime time number timeunit;
define how long an IPsec-SA will be used, in timeunits. Any proposal will
be accepted, and no attribute(s) will be proposed to the peer if you do not
specify it(them). See the proposal_check directive.
remoteid number;
Sainfos will only be used if their remoteid matches the ph1id of the remote
section used for phase 1. Defaults to 0, which is also the default for
ph1id.

racoon(8) does not have a list of security protocols to be negotiated. The list of
security protocols are passed by SPD in the kernel. Therefore you have to define
all of the potential algorithms in the phase 2 proposals even if there are
algorithms which will not be used. These algorithms are define by using the
following three directives, with a single comma as the separator. For algorithms
that can take variable-length keys, algorithm names can be followed by a key length,
like “blowfish 448”. racoon(8) will compute the actual phase 2 proposals by
computing the permutation of the specified algorithms, and then combining them with
the security protocol specified by the SPD. For example, if des, 3des, hmac_md5,
and hmac_sha1 are specified as algorithms, we have four combinations for use with
ESP, and two for AH. Then, based on the SPD settings, racoon(8) will construct the
actual proposals. If the SPD entry asks for ESP only, there will be 4 proposals.
If it asks for both AH and ESP, there will be 8 proposals. Note that the kernel may
not support the algorithm you have specified.
encryption_algorithm algorithms;
des, 3des, des_iv64, des_iv32, rc5, rc4, idea, 3idea, cast128, blowfish,
null_enc, twofish, rijndael, aes, camellia (used with ESP)
authentication_algorithm algorithms;
des, 3des, des_iv64, des_iv32, hmac_md5, hmac_sha1, hmac_sha256,
hmac_sha384, hmac_sha512, non_auth (used with ESP authentication and AH)
compression_algorithm algorithms;
deflate (used with IPComp)

Logging level
log level;
Defines the logging level. level is one of following: error, warning, notify, info,
debug or debug2. The default is info. If you set the logging level too high on
slower machines, IKE negotiation can fail due to timing constraint changes.

Specifies the way to pad
padding { statements }
specifies the padding format. The following are valid statements:
randomize (on | off);
Enables the use of a randomized value for padding. The default is on.
randomize_length (on | off);
The pad length will be random. The default is off.
maximum_length number;
Defines a maximum padding length. If randomize_length is off, this is
ignored. The default is 20 bytes.
exclusive_tail (on | off);
Means to put the number of pad bytes minus one into the last part of the
padding. The default is on.
strict_check (on | off);
Means to constrain the peer to set the number of pad bytes. The default is
off.

ISAKMP mode configuration settings
mode_cfg { statements }
Defines the information to return for remote hosts' ISAKMP mode config requests.
Also defines the authentication source for remote peers authenticating through
Xauth.

The following are valid statements:
auth_source (system | radius | pam | ldap);
Specifies the source for authentication of users through Xauth. system
means to use the Unix user database. This is the default. radius means to
use a RADIUS server. It works only if racoon(8) was built with libradius
support. Radius configuration is handled by statements in the radiuscfg
section. pam means to use PAM. It works only if racoon(8) was built with
libpam support. ldap means to use LDAP. It works only if racoon(8) was
built with libldap support. LDAP configuration is handled by statements in
the ldapcfg section.
auth_groups group1, ...;
Specifies the group memberships for Xauth in quoted group name strings.
When defined, the authenticating user must be a member of at least one group
for Xauth to succeed.
group_source (system | ldap);
Specifies the source for group validation of users through Xauth. system
means to use the Unix user database. This is the default. ldap means to
use LDAP. It works only if racoon(8) was built with libldap support and
requires LDAP authentication. LDAP configuration is handled by statements
in the ldapcfg section.
conf_source (local | radius | ldap);
Specifies the source for IP addresses and netmask allocated through ISAKMP
mode config. local means to use the local IP pool defined by the network4
and pool_size statements. This is the default. radius means to use a
RADIUS server. It works only if racoon(8) was built with libradius support
and requires RADIUS authentication. RADIUS configuration is handled by
statements in the radiuscfg section. ldap means to use an LDAP server. It
works only if racoon(8) was built with libldap support and requires LDAP
authentication. LDAP configuration is handled by statements in the ldapcfg
section.
accounting (none | system | radius | pam);
Enables or disables accounting for Xauth logins and logouts. The default is
none which disable accounting. Specifying system enables system accounting
through utmp(5). Specifying radius enables RADIUS accounting. It works
only if racoon(8) was built with libradius support and requires RADIUS
authentication. RADIUS configuration is handled by statements in the
radiuscfg section. Specifying pam enables PAM accounting. It works only if
racoon(8) was build with libpam support and requires PAM authentication.
pool_size size
Specify the size of the IP address pool, either local or allocated through
RADIUS. conf_source selects the local pool or the RADIUS configuration, but
in both configurations, you cannot have more than size users connected at
the same time. The default is 255.
network4 address;
netmask4 address;
The local IP pool base address and network mask from which dynamically
allocated IPv4 addresses should be taken. This is used if conf_source is
set to local or if the RADIUS server returned 255.255.255.254. Default is
0.0.0.0/0.0.0.0.
dns4 addresses;
A list of IPv4 addresses for DNS servers, separated by commas, or on
multiple dns4 lines.
wins4 addresses;
A list of IPv4 address for WINS servers. The keyword
nbns4 can also be used as an alias for
wins4.
split_network (include | local_lan) network/mask, ...
The network configuration to send, in CIDR notation (e.g. 192.168.1.0/24).
If include is specified, the tunnel should be only used to encrypt the
indicated destinations ; otherwise, if local_lan is used, everything will
pass through the tunnel but those destinations.
default_domain domain;
The default DNS domain to send.
split_dns domain, ...
The split dns configuration to send, in quoted domain name strings. This
list can be used to describe a list of domain names for which a peer should
query a modecfg assigned dns server. DNS queries for all other domains
would be handled locally. (Cisco VPN client only).
banner path;
The path of a file displayed on the client at connection time. Default is
/etc/motd.
auth_throttle delay;
On each failed Xauth authentication attempt, refuse new attempts for a set
delay of seconds. This is to avoid dictionary attacks on Xauth passwords.
Default is one second. Set to zero to disable authentication delay.
pfs_group group;
Sets the PFS group used in the client proposal (Cisco VPN client only).
Default is 0.
save_passwd (on | off);
Allow the client to save the Xauth password (Cisco VPN client only).
Default is off.

Ldap configuration settings
ldapcfg { statements }
Defines the parameters that will be used to communicate with an ldap server for
xauth authentication.

The following are valid statements:
version (2 | 3);
The ldap protocol version used to communicate with the server. The default
is 3.
host (hostname | address);
The host name or ip address of the ldap server. The default is localhost.
port number;
The port that the ldap server is configured to listen on. The default is
389.
base distinguished name;
The ldap search base. This option has no default value.
subtree (on | off);
Use the subtree ldap search scope. Otherwise, use the one level search
scope. The default is off.
bind_dn distinguished name;
The user dn used to optionally bind as before performing ldap search
operations. If this option is not specified, anonymous binds are used.
bind_pw string;
The password used when binding as bind_dn.
attr_user attribute name;
The attribute used to specify a users name in an ldap directory. For
example, if a user dn is "cn=jdoe,dc=my,dc=net" then the attribute would be
"cn". The default value is cn.
attr_addr attribute name;
attr_mask attribute name;
The attributes used to specify a users network address and subnet mask in an
ldap directory. These values are forwarded during mode_cfg negotiation when
the conf_source is set to ldap. The default values are racoon-address and
racoon-netmask.
attr_group attribute name;
The attribute used to specify a group name in an ldap directory. For
example, if a group dn is "cn=users,dc=my,dc=net" then the attribute would
be "cn". The default value is cn.
attr_member attribute name;
The attribute used to specify group membership in an ldap directory. The
default value is member.

Radius configuration settings
radiuscfg { statements }
Defines the parameters that will be used to communicate with radius servers for
xauth authentication. If radius is selected as the xauth authentication or
accounting source and no servers are defined in this section, settings from the
system radius.conf(5) configuration file will be used instead.

The following are valid statements:
auth (hostname | address) [port] sharedsecret;
The host name or ip address, optional port value and shared secret value of
a radius authentication server. Up to 5 radius authentication servers may
be specified using multiple lines.
acct (hostname | address) [port] sharedsecret;
The host name or ip address, optional port value and shared secret value of
a radius accounting server. Up to 5 radius accounting servers may be
specified using multiple lines.
timeout seconds;
The timeout for receiving replies from radius servers. The default is 3.
retries count;
The maximum number of repeated requests to make before giving up on a radius
server. The default is 3.

Special directives
complex_bundle (on | off);
defines the interpretation of proposal in the case of SA bundle. Normally “IP AH
ESP IP payload” is proposed as “AH tunnel and ESP tunnel”. The interpretation is
more common to other IKE implementations, however, it allows very limited set of
combinations for proposals. With the option enabled, it will be proposed as “AH
transport and ESP tunnel”. The default value is off.

Pre-shared key File
The pre-shared key file defines pairs of identifiers and corresponding shared secret keys
which are used in the pre-shared key authentication method in phase 1. The pair in each
line is separated by some number of blanks and/or tab characters like in the hosts(5) file.
Key can include blanks because everything after the first blanks is interpreted as the
secret key. Lines starting with ‘#’ are ignored. Keys which start with ‘0x’ are
interpreted as hexadecimal strings. Note that the file must be owned by the user ID running
racoon(8) (usually the privileged user), and must not be accessible by others.

EXAMPLES

     The following shows how the remote directive should be configured.

     path pre_shared_key "/usr/local/v6/etc/psk.txt" ;
     remote anonymous
     {
             exchange_mode aggressive,main,base;
             lifetime time 24 hour;
             proposal {
                     encryption_algorithm 3des;
                     hash_algorithm sha1;
                     authentication_method pre_shared_key;
                     dh_group 2;
             }
     }

     sainfo anonymous
     {
             pfs_group 2;
             lifetime time 12 hour ;
             encryption_algorithm 3des, blowfish 448, twofish, rijndael ;
             authentication_algorithm hmac_sha1, hmac_md5 ;
             compression_algorithm deflate ;
     }

     If you are configuring plain RSA authentication, the remote directive should look like the
     following:

     path certificate "/usr/local/v6/etc" ;
     remote anonymous
     {
             exchange_mode main,base ;
             lifetime time 12 hour ;
             certificate_type plain_rsa "/usr/local/v6/etc/myrsakey.priv";
             peers_certfile plain_rsa "/usr/local/v6/etc/yourrsakey.pub";
             proposal {
                             encryption_algorithm aes ;
                             hash_algorithm sha1 ;
                             authentication_method rsasig ;
                             dh_group 2 ;
             }
     }

     The following is a sample for the pre-shared key file.

     10.160.94.3     mekmitasdigoat
     172.16.1.133    0x12345678
     194.100.55.1    whatcertificatereally
     3ffe:501:410:ffff:200:86ff:fe05:80fa    mekmitasdigoat
     3ffe:501:410:ffff:210:4bff:fea2:8baa    mekmitasdigoat
     foo@kame.net    mekmitasdigoat
     foo.kame.net    hoge

HISTORY

     The racoon.conf configuration file first appeared in the “YIPS” Yokogawa IPsec
     implementation.

BUGS

     Some statements may not be handled by racoon(8) yet.

     Diffie-Hellman computation can take a very long time, and may cause unwanted timeouts,
     specifically when a large D-H group is used.

SECURITY CONSIDERATIONS