Provided by: sidplayfp_188.8.131.52-1_amd64
sindplayfp.ini - Configuration file for sidplayfp(1).
This page describes the options available for the configuration file of Sidplayfp. It is composed by a number of sections, each one composed by a section name, enclosed by square brackets, folowed by a list of <parameter>=<value> lines. sidplayfp.ini supports the following sections: [SIDPlayfp] - Generic configuration [Console] - Console appearance configuration [Audio] - Audio output configuration [Emulation] - Emulation engine parameters All options and values (except for file names and paths) are case insensitive, and are described in detail below. For any of the following parameter, if it's specified more than one time the last entry encountered will be used. NOTE: if any of these options is specified outside its section, it will be ignored.
Version=<number> Configuration version Songlength Database=<path> Full path for the Songlength DB. Should point to the DOCUMENTS/Songlengths.txt file under the HVSC collection path. On *NIX systems if this value is not set, sidplayfp will try $PREFIX/share/sidplayfp/Songlengths.txt . Default Play Length=mm:ss Default play time if Songlength Database is not found. Default Record Length=mm:ss Default recording time when writing wave files if Songlength Database is not found. Kernal Rom=<path> Full path for the Kernal Rom file. This is the most important rom and should always be provided, although many tunes will still work without. By default the program will look for a kernal file under the following locations: · $XDG_DATA_HOME/sidplayfp/ on *NIX systems where XDG_DATA_HOME is defined. · $HOME/.local/share/sidplayfp/ on *NIX systems where XDG_DATA_HOME is not defined. · $PREFIX/share/sidplayfp on *NIX systems when not found in the above directories. · %CSIDL_APPDATA%\sidplayfp\ on Windows systems where CSIDL_APPDATA is defined. · %USERPROFILE%\Application Data\sidplayfp\ on Windows systems where CSIDL_APPDATA is not defined. Basic Rom=<path> Full path for the Basic Rom file. This is moslty useful for playing BASIC tunes. By default the program will look for a basic file under the same locations as above. Chargen Rom=<path> Full path for the Character generator Rom file. Almost useless for playback of tunes, but included for completeness. By default the program will look for a chargen file under the same locations as above.
Ansi=true|false Use ANSI escape sequences to provide colored output if supported by the terminal. Char Top Left=<char> Character for the top left corner. Char Top Right=<char> Character for the top right corner. Char Bottom Left=<char> Character for the bottom left corner. Char Bottom Right=<char> Character for the bottom right corner. Char Vertical=<char> Character for vertical lines. Char Horizontal=<char> Character for horizontal lines. Char Junction Left=<char> Character for left junctions. Char Junction Right=<char> Character for right junctions.
Frequency=<number> Playback frequency expressed in Hertz. Channels=<number> Number of channels, 1 for mono and 2 for stereo playback. BitsPerSample=<16|32> Number of bits ber sample, used only for wav output. Using values other than the ones specified will produce invalid output.
C64Model=<PAL|NTSC|OLD_NTSC|DREAN> Default c64 model, PAL for european PAL-B model, NTSC for american/japanese NTSC-M models, OLD_NTSC for NTSC-M models with old video chip and DREAN for argentinian PAL-N model. ForceC64Model=true|false Force the selected c64 model wven if the tune states otherwise. SidModel=<MOS6581|MOS8580> Default SID chip model, old MOS 6581 or newer MOS 8580 ForceSidModel=true|false Force the selected SID chip model wven if the tune states otherwise. UseFilter=true|false Enable/disable the emulation of the SID filter. FilterBias=<number> Controls the filter bias in the ReSID emulation. The bias is given in millivolts, and a maximum reasonable control range is approximately -500 to 500 FilterCurve6581=<number> Controls the filter curve for the 6581 model in the ReSIDfp emulation. Ranges from 0.0 (light) to 1.0 (dark), the default value is 0.5 FilterCurve8580=<number> Controls the filter curve for the 8580 model in the ReSIDfp emulation. Value is expressed in Hertz and the default is 12500
Sidplayfp Homepage: http://sourceforge.net/projects/sidplay-residfp/ Sidplay2 homepage: http://sidplay2.sourceforge.net/ High Voltage Sid Collection (HVSC): http://hvsc.c64.org/
sidplay2 - Simon White <firstname.lastname@example.org> sidplay - Michael Schwendt <email@example.com> reSID engine - Dag Lem <firstname.lastname@example.org> reSIDfp engine - Antti Lankila <email@example.com> man-page - Mikko Kilponen <firstname.lastname@example.org>