NAME

     ipmi — OpenIPMI compatible IPMI interface driver

SYNOPSIS

     device ipmi

     To manually specify I/O attachment in /boot/device.hints:
     hint.ipmi.0.at="isa"
     hint.ipmi.0.port="0xCA2"
     hint.ipmi.0.spacing="8"
     hint.ipmi.0.mode="KCS"

     To manually specify memory attachment in /boot/device.hints:
     hint.ipmi.0.at="isa"
     hint.ipmi.0.maddr="0xf0000000"
     hint.ipmi.0.spacing="8"
     hint.ipmi.0.mode="SMIC"

     Meaning of spacing:
           8    8 bit alignment
           16   16 bit alignment
           32   32 bit alignment

     If the port and spacing are not specified the interface type default will be used.  Only
     specify either the port for I/O access or maddr for memory access.

DESCRIPTION

     The IPMI (Intelligent Platform Management Interface) is a standard for monitoring system
     hardware by permitting generic code to detect and monitor the sensors in a system.  The IPMI
     standard offers watchdog support, an FRU database, and other support extensions.  It is
     currently being adopted by the makers of many single board and embedded system
     manufacturers.

     The ipmi driver in FreeBSD is heavily adopted from the standard and Linux driver; however,
     not all features described in the standard are supported.

IOCTLS

     Sending and receiving messages through the ipmi driver requires the use of ioctl(2).  The
     ioctls are used due to the complexity of data sent to and from the device.  The ioctl(2)
     command codes below are defined in <sys/ipmi.h>.  The third argument to ioctl(2) should be a
     pointer to the type indicated.

     Currently the following ioctls are supported:

     IPMICTL_RECEIVE_MSG (struct ipmi_recv)
             Receive a message.  Possible error values:

             [EAGAIN]           No messages are in the process queue.

             [EFAULT]           An address supplied was invalid.

             [EMSGSIZE]         The address could not fit in the message buffer and will remain
                                in the buffer.

     IPMICTL_RECEIVE_MSG_TRUNC (struct ipmi_recv)
             Like IPMICTL_RECEIVE_MSG but if the message cannot fit into the buffer, it will
             truncate the contents instead of leaving the data in the buffer.

     IPMICTL_SEND_COMMAND (struct ipmi_req)
             Send a message to the interface.  Possible error values:

             [EFAULT]           An address supplied was invalid.

             [ENOMEM]           Buffers could not be allowed for the command, out of memory.

     IPMICTL_SET_MY_ADDRESS_CMD (unsigned int)
             Set the slave address for source messages.

     IPMICTL_GET_MY_ADDRESS_CMD (unsigned int)
             Get the slave address for source messages.

     IPMICTL_SET_MY_LUN_CMD (unsigned int)
             Set the slave LUN for source messages.

     IPMICTL_GET_MY_LUN_CMD (unsigned int)
             Get the slave LUN for source messages.

   Unimplemented Ioctls
     IPMICTL_REGISTER_FOR_CMD (struct ipmi_cmdspec)
             Register to receive a specific command.  Possible error values:

             [EFAULT]           An supplied address was invalid.

             [EBUSY]            The network function/command is already in use.

             [ENOMEM]           Could not allocate memory.

     IPMICTL_UNREGISTER_FOR_CMD (struct ipmi_cmdspec)
             Unregister to receive a specific command.  Possible error values:

             [EFAULT]           An address supplied was invalid.

             [ENOENT]           The network function/command was not found.

   Stub Only Ioctl
     IPMICTL_SET_GETS_EVENTS_CMD (int)
             Set whether this interface receives events.  Possible error values:

             [EFAULT]           An address supplied was invalid.

SEE ALSO

     ioctl(2), watchdog(4), watchdog(8), watchdogd(8), watchdog(9)

HISTORY

     The ipmi driver first appeared in FreeBSD 6.2.

AUTHORS

     The ipmi driver was written by Doug Ambrisko <ambrisko@FreeBSD.org>.  This manual page was
     written by Tom Rhodes <trhodes@FreeBSD.org>.

BUGS

     Not all features of the MontaVista driver are supported.

     Currently, IPMB and BT modes are not implemented.