Provided by: freebsd-manpages_10.1~RC1-1_all bug

NAME

     uftdi — USB support for serial adapters based on the FTDI family of USB serial adapter
     chips.

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device usb
           device ucom
           device uftdi

     Alternatively, to load the driver as a module at boot time, place the following line in
     loader.conf(5):

           uftdi_load="YES"

DESCRIPTION

     The uftdi driver provides support for various serial adapters based on the following FTDI
     chips:

     ·   FT8U100AX
     ·   FT8U232AM
     ·   FT8U232BM
     ·   FT232R
     ·   FT2232C
     ·   FT2232D
     ·   FT2232H
     ·   FT4232H
     ·   FT230X

     The device is accessed through the ucom(4) driver which makes it behave like a tty(4).

     Many of the supported chips provide additional functionality such as bitbang mode and the
     MPSSE engine for serial bus emulation.  The uftdi driver provides access to that
     functionality with the following ioctl(2) calls, defined in <dev/usb/uftdiio.h>:

     UFTDIIOC_RESET_IO (int)
             Reset the channel to its default configuration, flush RX and TX FIFOs.

     UFTDIIOC_RESET_RX (int)
             Flush the RX FIFO.

     UFTDIIOC_RESET_TX (int)
             Flush the TX FIFO.

     UFTDIIOC_SET_BITMODE (struct uftdi_bitmode)
             Put the channel into the operating mode specified in mode, and set the pins
             indicated by ones in iomask to output mode.  The mode must be one of the
             uftdi_bitmodes values.

             enum uftdi_bitmodes
             {
                     UFTDI_BITMODE_ASYNC = 0,
                     UFTDI_BITMODE_MPSSE = 1,
                     UFTDI_BITMODE_SYNC = 2,
                     UFTDI_BITMODE_CPU_EMUL = 3,
                     UFTDI_BITMODE_FAST_SERIAL = 4,
                     UFTDI_BITMODE_CBUS = 5,
                     UFTDI_BITMODE_NONE = 0xff,
             };

             struct uftdi_bitmode
             {
                     uint8_t mode;
                     uint8_t iomask;
             };

             Manuals and application notes published by FTDI describe these modes in detail.  To
             use most of these modes, you first put the channel into the desired mode, then you
             read(2) and write(2) data which either reflects pin state or is interpreted as MPSSE
             commands and parameters, depending on the mode.

     UFTDIIOC_GET_BITMODE (struct uftdi_bitmode)
             Return the state of the bitbang pins at the time of the call in the iomask member.
             The mode member is unused.

     UFTDIIOC_SET_ERROR_CHAR (int)
             Set the character which is inserted into the buffer to mark the point of an error
             such as FIFO overflow.

     UFTDIIOC_SET_EVENT_CHAR (int)
             Set the character which causes a partial FIFO full of data to be returned
             immediately even if the FIFO is not full.

     UFTDIIOC_SET_LATENCY (int)
             Set the amount of time to wait for a full FIFO, in milliseconds.  If more than this
             much time elapses without receiving a new character, any characters in the FIFO are
             returned.

     UFTDIIOC_GET_LATENCY (int)
             Get the current value of the latency timer.

     UFTDIIOC_GET_HWREV (int)
             Get the hardware revision number.  This is the bcdDevice value from the
             usb_device_descriptor.

HARDWARE

     The uftdi driver supports the following adapters:

     ·   B&B Electronics USB->RS422/485 adapter
     ·   Elexol USB MOD1 and USB MOD3
     ·   HP USB-Serial adapter shipped with some HP laptops
     ·   Inland UAS111
     ·   QVS USC-1000
     ·   Buffalo PC-OP-RS / Kurouto-shikou KURO-RS universal remote
     ·   Prologix GPIB-USB Controller

SEE ALSO

     tty(4), ucom(4), usb(4)

HISTORY

     The uftdi driver appeared in FreeBSD 4.8 from NetBSD 1.5.