Provided by: sg3-utils_1.40-0ubuntu1_amd64 
NAME
sg_vpd - fetch SCSI VPD page and/or decode its response
SYNOPSIS
sg_vpd [--all] [--enumerate] [--help] [--hex] [--ident] [--inhex=FN] [--long] [--maxlen=LEN] [--page=PG]
[--quiet] [--raw] [--vendor=VP] [--verbose] [--version] [DEVICE]
DESCRIPTION
This utility, when DEVICE is given, fetches a Vital Product Data (VPD) page and decodes it or outputs it
in ASCII hexadecimal or binary. VPD pages are fetched with a SCSI INQUIRY command.
Alternatively the --inhex=FN option can be given. In this case FN is assumed to be a file name ('-' for
stdin) containing ASCII hexadecimal representing a VPD page response. If the --raw option is also given
then binary input is assumed (rather than ASCII hexadecimal).
Probably the most important page is the Device Identification VPD page (page number: 0x83). Since SPC-3,
support for this page has been flagged as mandatory. This page can be fetched by using the --ident
option.
The reference document used for interpreting VPD pages (and the INQUIRY standard response) is T10/1713-D
Revision 37 (SPC-4, 17 May 2014) found at http://www.t10.org .
When no options are given, other than a DEVICE, then the "Supported VPD pages" (0x0) VPD page is fetched
and decoded.
OPTIONS
Arguments to long options are mandatory for short options as well. The options are arranged in
alphabetical order based on the long option name.
-a, --all
decode all VPD pages. When used with DEVICE the pages to be decoded are found in the "Supported
VPD pages" VPD page.
If this option is used with the --inhex=FN option then the file FN is assumed to contain 1 or more
VPD pages (in ASCII hex or binary). Decoding continues until the file is exhausted (or an error
occurs). Sanity checks are aplied on each VPD page's length and the ascending order of VPD page
numbers (required by SPC-4) so bad data may be detected.
If the --page=PG option is also given then no VPD page whose page number is greater than PG (or
its numeric equivalent) is decoded.
-e, --enumerate
list the names of the known VPD pages, first the standard pages (i.e. those defined by T10), then
the vendor specific pages. Each group is sorted in abbreviation order. The DEVICE and most other
options are ignored and this utility exits after listing the VPD page names. May be used together
with --page=PG where PG is numeric. If so, it searches for the summary lines of all VPD pages
whose number matches PG. May be used with --vendor=VP to restrict output to known vendor specific
pages for vendor/product VP.
-h, --help
outputs the usage message summarizing command line options then exits. Ignores DEVICE if given.
-H, --hex
outputs the requested VPD page in ASCII hexadecimal. Can be used multiple times, see section on
the ATA information vpd page.
To generate output suitable for placing in a file that can be used by a later invocation with the
--inhex=FN option, use the '-HHHH' option (e.g. 'sg_vpd -p di -HHHH /dev/sg3 > dev_id.hex'). The
reason '-HHHH' is used is to flag that unadorned hexadecimal (without other text or address
offsets) is sent to stdout.
-i, --ident
decode the device identification (0x83) VPD page. When used once this option has the same effect
as '--page=di'. When use twice then the short form of the device identification VPD page's logical
unit designator is decoded. In the latter case this option has the same effect as '--quiet
--page=di_lu'.
-I, --inhex=FN
FN is expected to be a file name (or '-' for stdin) which contains ASCII hexadecimal or binary
representing a VPD page (or a standard INQUIRY) response. This utility will then decode that
response. It is preferable to also supply the --page=PG option, if not this utility will attempt
to guess which VPD page (or standard INQUIRY) the response is associated with. The hexadecimal
should be arranged as 1 or 2 digits representing a byte each of which is whitespace or comma
separated. Anything from and including a hash mark to the end of line is ignored. If the --raw
option is also given then FN is treated as binary.
-l, --long
when decoding some VPD pages, give a little more output. For example the ATA Information VPD page
only shows the signature (in hex) and the IDENTIFY (PACKET) DEVICE (in hex) when this option is
given.
-m, --maxlen=LEN
where LEN is the (maximum) response length in bytes. It is placed in the cdb's "allocation length"
field. If not given (or LEN is zero) then 252 is used (apart from the ATA Information VPD page
which defaults to 572) and, if the response indicates this value is insufficient, another INQUIRY
command is sent with a larger value in the cdb's "allocation length" field. If this option is
given and LEN is greater than 0 then only one INQUIRY command is sent. Since many simple devices
implement the INQUIRY command badly (and do not support VPD pages) then the safest value to use
for LEN is 36. See the sg_inq man page for the more information.
-p, --page=PG
where PG is the VPD page to be decoded or output. The PG argument can either be an abbreviation, a
number or a pair or numbers/abbreviations separated by a comma. The VPD page abbreviations can be
seen by using the --enumerate option. If a number is given it is assumed to be decimal unless it
has a hexadecimal indicator which is either a leading '0x' or a trailing 'h'. If one number is
given then it is assumed to be a VPD page number. If two numbers (or abbreviations) are given then
the second one is the same as VP (see the --vendor=VP option). If this option is not given (nor
'-i', '-l' nor '-V') then the "Supported VPD pages" (0x0) VPD page is fetched and decoded. If PG
is '-1' or 'sinq' then the standard INQUIRY response is output. This option may also be used with
the --enumerate (see its description).
-q, --quiet
suppress the amount of decoding output.
-r, --raw
if not used with --inhex=FN then output requested VPD page in binary. The output should be piped
to a file or another utility when this option is used. The binary is sent to stdout, and errors
are sent to stderr.
if used with --inhex=FN then the contents of FN is treated as binary.
-M, --vendor=VP
where VP is a vendor (e.g. "sea" for Seagate) or vendor/product acronym (e.g. "hp3par" for the
3PAR array from HP). Many vendors have re-used the numbers at the beginning of the vendor specific
VPD page range (e.g. page 0xc0) and this option is a way of selecting only those which are of
interest. Using a VP of "xxx" will list the available acronyms.
If this option is used with --page=PG and PG is an acronym then this option is ignored. If PG is a
number (e.g. 0xc0) then VP is used to choose the which vendor specific page (e.g. sharing page
number 0xc0) to decode.
-v, --verbose
increases the level or verbosity.
-V, --version
print out version string then exit.
ATA INFORMATION VPD PAGE
This VPD page (0x89 or 'ai') is defined by the SCSI to ATA Translation standard. It contains information
about the SAT layer, the "signature" of the ATA device and the response to the ATA IDENTIFY (PACKET)
DEVICE command. The latter part has 512 bytes of identity, capability and settings data which the hdparm
utility is capable of decoding (so this utility doesn't decode it).
To unclutter the output for this page, the signature and the IDENTIFY (PACKET) DEVICE response are not
output unless the --long option (or --hex or --raw) are given. When the --long option is given the
IDENTIFY (PACKET) DEVICE response is output as 256 (16 bit) words as is the fashion for ATA devices. To
see that response as a string of bytes use the '-HH' option. To format the output suitable for hdparm to
decode use either the '-HHH' or '-rr' option. For example if 'dev/sdb' is a SATA disk behind a SAT layer
then this command: 'sg_vpd -p ai -HHH /dev/sdb | hdparm --Istdin' should decode the ATA IDENTIFY (PACKET)
DEVICE response.
NOTES
Since some VPD pages (e.g. the Extended INQUIRY page) depend on settings in the standard INQUIRY
response, then the standard INQUIRY response is output as a pseudo VPD page when PG is set to '-1' or
'sinq'. Also the decoding of some fields (e.g. the Extended INQUIRY page's SPT field) is expanded when
the '--long' option is given using the standard INQUIRY response information (e.g. the PDT and the
PROTECT fields).
In the 2.4 series of Linux kernels the DEVICE must be a SCSI generic (sg) device. In the 2.6 series block
devices (e.g. disks and ATAPI DVDs) can also be specified. For example "sg_inq /dev/sda" will work in the
2.6 series kernels. From lk 2.6.6 other SCSI "char" device names may be used as well (e.g. "/dev/st0m").
The DEVICE is opened with a read-only flag (e.g. in Unix with the O_RDONLY flag).
EXIT STATUS
The exit status of sg_vpd is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
EXAMPLES
The examples in this page use Linux device names. For suitable device names in other supported Operating
Systems see the sg3_utils(8) man page.
To see the VPD pages that a device supports, use with no options. The command line invocation is shown
first followed by a typical response:
# sg_vpd /dev/sdb
Supported VPD pages VPD page:
Supported VPD pages [sv]
Unit serial number [sn]
Device identification [di]
Extended inquiry data [ei]
Block limits (SBC) [bl]
To see the VPD page numbers associated with each supported page then add the '--long' option to the above
command line. To view a VPD page either its number or abbreviation can be given to the '--page=' option.
The page name abbreviations are shown within square brackets above. In the next example the Extended
inquiry data VPD page is listed:
# sg_vpd --page=ei /dev/sdb
extended INQUIRY data VPD page:
ACTIVATE_MICROCODE=0 SPT=0 GRD_CHK=0 APP_CHK=0 REF_CHK=0
UASK_SUP=0 GROUP_SUP=0 PRIOR_SUP=0 HEADSUP=1 ORDSUP=1 SIMPSUP=1
WU_SUP=0 CRD_SUP=0 NV_SUP=0 V_SUP=0
P_I_I_SUP=0 LUICLR=0 R_SUP=0 CBCS=0
Multi I_T nexus microcode download=0
Extended self-test completion minutes=0
POA_SUP=0 HRA_SUP=0 VSA_SUP=0
To check if any protection types are supported by a disk use the '--long' option on the Extended inquiry
data VPD page:
# sg_vpd --page=ei --long /dev/sdb
extended INQUIRY data VPD page:
ACTIVATE_MICROCODE=0
SPT=1 [protection types 1 and 2 supported]
GRD_CHK=1
....
Search for the name (and acronym) of all pages that share VPD page number 0xb0 .
# sg_vpd --page=0xb0 --enumerate
Matching standard VPD pages:
bl 0xb0 Block limits (SBC)
oi 0xb0 OSD information
sad 0xb0 Sequential access device capabilities (SSC)
Some examples follow using the "--all" option. Send an ASCII hexadecimal representation of all VPD pages
to a file:
# sg_vpd --all -HHHH /dev/sg3 > all_vpds.hex
At some later time that file could be decoded with:
# sg_vpd --all --inhex=all_vpds.hex
To do the equivalent as the previous example but use a file containing binary:
# sg_vpd --all --raw /dev/sg3 > all_vpds.bin
# sg_vpd --all --raw --inhex=all_vpds.bin
Notice that "--raw" must be given with the second (--inhex) invocation to alert the utility that
all_vpds.bin contains binary as it assumes ASCII hexadecimal by default. Next we only decode T10
specified VPD pages excluding vendor specific VPD pages that start at page number 0xc0:
# sg_vpd --all --page=0xbf --raw --inhex=all_vpds.bin
Further examples can be found on the http://sg.danny.cz/sg/sg3_utils.html web page.
AUTHOR
Written by Douglas Gilbert
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright © 2006-2014 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO warranty; not even for MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_inq(sg3_utils), sg3_utils(sg3_utils), sdparm(sdparm), hdparm(hdparm)