Ubuntu Manpage: DS2406, DS2407 - Dual Addressable Switch with 1kbit Memory, Hidable Dual Addressable

Provided by: owfs-doc_3.1p1-2ubuntu1_all

NAME

       DS2406,  DS2407  -  Dual  Addressable  Switch  with 1kbit Memory, Hidable Dual Addressable
       Switch with 1kbit Memory

SYNOPSIS

       Dual Switch, Write-once Memory

       12 [.]XXXXXXXXXXXX[XX][/[ channels | latch.[A|B|ALL|BYTE] | memory |  pages/page.[0-3|ALL]
       |    PIO.[A|B|ALL|BYTE]    |    power    |    sensed.[A|B|ALL|BYTE]    |    set_alarm    |
       TAI8570/[sibling|temperature|pressure] | T8A/volt.[0-7,ALL] address | crc8 | id |  locator
       | r_address | r_id | r_locator | type ]]

FAMILY CODE

SPECIAL PROPERTIES

channels
read-only, unsigned integer
Is this a 1 or 2 channel switch? The DS2406 comes in two forms, one has only one PIO pin
(PIO.A). Returns 1 or 2.

latch.A latch.B latch.ALL latch.BYTE
read-write, yes-no
The activity latch is set to 1 with the first negative or positive edge detected on the
associated PIO channel.
Writing any data will clear latch for all (both)) channels. This is a hardware "feature"
of the chip.
ALL references both channels simultaneously, comma separated
BYTE references both channels simultaneously as a single byte, with channel A in bit 0.

memory
read-write, binary
128 bytes of non-volatile, write-once data.

pages/page.0 ... pages/page.3 pages/page.ALL
read-write, binary
Memory organized as 4 pages or 32 bytes. Memory is write-once.
ALL is the aggregate of all 4 pages, sequentially accessed.

PIO.A PIO.B PIO.ALL PIO.BYTE
read-write, yes-no
State of the open-drain output ( PIO ) pin. 0 = non-conducting (off), 1 = conducting (on).
Writing zero will turn off the switch, non-zero will turn on the switch. Reading the PIO
state will return the switch setting (flipflop in the data sheet). To determine the actual
logic level at the switch, refer to the sensed property.
Note that the actual pin setting for the chip uses the opposite polarity -- 0 for
conducting, 1 for non-conducting. However, to turn a connected device on (i.e. to deliver
power) we use the software concept of 1 as conducting or "on".
ALL references both channels simultaneously, comma separated.
BYTE references both channels simultaneously as a single byte, with channel A in bit 0.

power
read-only, yes-no
Is the DS2406 powered parasitically =0 or separately on the Vcc pin =1

sensed.A sensed.B sensed.ALL sensed.BYTE
read-only, yes-no
Logic level at the PIO pin. 0 = ground. 1 = high (~2.4V - 5V ). Really makes sense only if
the PIO state is set to zero (off), else will read zero.
ALL references both channels simultaneously, comma separated.
BYTE references both channels simultaneously as a single byte, with channel A in bit 0.

set_alarm
read-write, unsigned integer (0-331)
A number consisting of three digits XYZ, where:

X channel selection
0 neither
1 A only
2 B only
3 A or B

Y source selection
0 undefined
1 latch
2 PIO
3 sensed

Z polarity selection
0 low
1 high

All digits will be truncated to the 0-3 (or 0-1) range. Leading zeroes are optional (and
may be problematic for some shells).

Example:

311 Responds on Conditional Search when either latch.A or latch.B (or both) are set to
1.

<100 Never responds to Conditional Search.

TAI8570/
subdirectory
Properties when the DS2406 (3) is built into a TAI8570.
If the DS2406 (3) is not part of a TAI8570 or is not the controlling switch, attempts to
read will result in an error.

TAI8570/pressure
read-only, floating point
Barometric pressure in millibar.

TAI8570/sibling
read-only, ascii
Hex address of the DS2406 (3) paired with this chip in a TAI8570.

TAI8570/temperature
read-only, floating-point
Ambient temperature measured by the TAI8570 in prevailing temperature units (Centigrade is
the default).

T8A/volt.[0-7|ALL]
read-only, floating-point
Uses the T8A (by Embedded Data Systems ) 8 channel voltage converter. Units in volts, 0 to
5V range. 12 bit resolution.

STANDARD PROPERTIES

address
r_address
read-only, ascii
The entire 64-bit unique ID. Given as upper case hexidecimal digits (0-9A-F).
address starts with the family code
r address is the address in reverse order, which is often used in other applications and
labeling.

crc8
read-only, ascii
The 8-bit error correction portion. Uses cyclic redundancy check. Computed from the
preceding 56 bits of the unique ID number. Given as upper case hexidecimal digits (0-9A-
F).

family
read-only, ascii
The 8-bit family code. Unique to each type of device. Given as upper case hexidecimal
digits (0-9A-F).

id
r_id
read-only, ascii
The 48-bit middle portion of the unique ID number. Does not include the family code or
CRC. Given as upper case hexidecimal digits (0-9A-F).
r id is the id in reverse order, which is often used in other applications and labeling.

locator
r_locator
read-only, ascii
Uses an extension of the 1-wire design from iButtonLink company that associated 1-wire
physical connections with a unique 1-wire code. If the connection is behind a Link Locator
the locator will show a unique 8-byte number (16 character hexidecimal) starting with
family code FE.
If no Link Locator is between the device and the master, the locator field will be all FF.
r locator is the locator in reverse order.

present (DEPRECATED)
read-only, yes-no
Is the device currently present on the 1-wire bus?

type
read-only, ascii
Part name assigned by Dallas Semi. E.g. DS2401 Alternative packaging (iButton vs chip)
will not be distiguished.

ALARMS

       Use the set_alarm property to set the alarm triggering criteria.

DESCRIPTION

1-Wire
1-wire is a wiring protocol and series of devices designed and manufactured by Dallas
Semiconductor, Inc. The bus is a low-power low-speed low-connector scheme where the data
line can also provide power.

Each device is uniquely and unalterably numbered during manufacture. There are a wide
variety of devices, including memory, sensors (humidity, temperature, voltage, contact,
current), switches, timers and data loggers. More complex devices (like thermocouple
sensors) can be built with these basic devices. There are also 1-wire devices that have
encryption included.

The 1-wire scheme uses a single bus master and multiple slaves on the same wire. The bus
master initiates all communication. The slaves can be individually discovered and
addressed using their unique ID.

Bus masters come in a variety of configurations including serial, parallel, i2c, network
or USB adapters.

OWFS design
OWFS is a suite of programs that designed to make the 1-wire bus and its devices easily
accessible. The underlying principle is to create a virtual filesystem, with the unique ID
being the directory, and the individual properties of the device are represented as simple
files that can be read and written.

Details of the individual slave or master design are hidden behind a consistent interface.
The goal is to provide an easy set of tools for a software designer to create monitoring
or control applications. There are some performance enhancements in the implementation,
including data caching, parallel access to bus masters, and aggregation of device
communication. Still the fundemental goal has been ease of use, flexibility and
correctness rather than speed.

DS2406
The DS2406 (3) allows control of other devices, like LEDs and relays. It superceeds the
DS2405 and DS2407 Alternative switches include the DS2408 or even DS2450
The DS2407 is practically identical to the DS2406 except for a strange hidden mode. It is
supported just like the DS2406

TAI8570
The TAI-8570 Pressure Sensor is based on a 1-wire composite device by AAG Electronica.
The TAI8570 uses 2 DS2406 (3) chips, paired as a reader and writer to synthesize 3-wire
communication. Only 1 of the DS2406 (3) will allow temperature or pressure readings. It's
mate's address can be shown as sibling.

The TAI8570 uses the Intersema MS5534a pressure sensor, and stores calibration and
temperature compensation values internally.

Design and code examples are available from AAG Electronica http://aag.com.mx , specific
permission to use code in a GPL product was given by Mr. Aitor Arrieta of AAG and Dr.
Simon Melhuish of OWW.

ADDRESSING

       All 1-wire devices are factory assigned a unique 64-bit address. This address  is  of  the
       form:

       Family Code
              8 bits

       Address
              48 bits

       CRC    8 bits

       Addressing under OWFS is in hexidecimal, of form:

              01.123456789ABC

       where 01 is an example 8-bit family code, and 12345678ABC is an example 48 bit address.

       The dot is optional, and the CRC code can included. If included, it must be correct.

DATASHEET

       http://pdfserv.maxim-ic.com/en/ds/DS2406.pdf
       http://pdfserv.maxim-ic.com/en/ds/DS2407.pdf
       http://www.embeddeddatasystems.com/page/EDS/PROD/IO/T8A
       http://oww.sourceforge.net/hardware.html#bp

AVAILABILITY

       http://www.owfs.org

AUTHOR

       Paul Alfille (paul.alfille@gmail.com)