Ubuntu Manpage: Smokeping::probes::CiscoRTTMonEchoICMP

NAME

       Smokeping::probes::CiscoRTTMonEchoICMP - Probe for SmokePing

SYNOPSIS

        *** Probes ***

        +CiscoRTTMonEchoICMP

        forks = 5
        offset = 50%
        step = 300
        timeout = 15

        # The following variables can be overridden in each target section
        ioshost = RTTcommunity@Myrouter.foobar.com.au # mandatory
        iosint = 10.33.22.11
        packetsize = 56
        pings = 5
        timeout = 15
        tos = 160
        vrf = INTERNET

        # [...]

        *** Targets ***

        probe = CiscoRTTMonEchoICMP # if this should be the default probe

        # [...]

        + mytarget
        # probe = CiscoRTTMonEchoICMP # if the default probe is something else
        host = my.host
        ioshost = RTTcommunity@Myrouter.foobar.com.au # mandatory
        iosint = 10.33.22.11
        packetsize = 56
        pings = 5
        timeout = 15
        tos = 160
        vrf = INTERNET

DESCRIPTION

       A probe for smokeping, which uses the ciscoRttMon MIB functionality ("Service Assurance
       Agent", "SAA") of Cisco IOS to measure ICMP echo ("ping") roundtrip times between a Cisco
       router and any IP address.

VARIABLES

Supported probe-specific variables:

forks
Run this many concurrent processes at maximum

Example value: 5

Default value: 5

offset
If you run many probes concurrently you may want to prevent them from hitting your
network all at the same time. Using the probe-specific offset parameter you can change
the point in time when each probe will be run. Offset is specified in % of total
interval, or alternatively as 'random', and the offset from the 'General' section is
used if nothing is specified here. Note that this does NOT influence the rrds itself,
it is just a matter of when data acqusition is initiated. (This variable is only
applicable if the variable 'concurrentprobes' is set in the 'General' section.)

Example value: 50%

step
Duration of the base interval that this probe should use, if different from the one
specified in the 'Database' section. Note that the step in the RRD files is fixed when
they are originally generated, and if you change the step parameter afterwards, you'll
have to delete the old RRD files or somehow convert them. (This variable is only
applicable if the variable 'concurrentprobes' is set in the 'General' section.)

Example value: 300

timeout
How long a single 'ping' takes at maximum

Example value: 15

Default value: 5

Supported target-specific variables:

ioshost
The (mandatory) ioshost parameter specifies the Cisco router, which will execute the
pings, as well as the SNMP community string on the router.

Example value: RTTcommunity@Myrouter.foobar.com.au

This setting is mandatory.

iosint
The (optional) iosint parameter is the source address for the pings sent. This should
be one of the active (!) IP addresses of the router to get results. IOS looks up the
target host address in the forwarding table and then uses the interface(s) listed
there to send the ping packets. By default IOS uses the (primary) IP address on the
sending interface as source address for a ping. The RTTMon MIB versions before IOS
12.0\fIs0(3)T didn't support this parameter.

Example value: 10.33.22.11

packetsize
The packetsize parameter lets you configure the packetsize for the pings sent. The
minimum is 8, the maximum 16392. Use the same number as with fping, if you want the
same packet sizes being used on the network.

Default value: 56

pings
How many pings should be sent to each target, if different from the global value
specified in the Database section. Note that the number of pings in the RRD files is
fixed when they are originally generated, and if you change this parameter afterwards,
you'll have to delete the old RRD files or somehow convert them.

Example value: 5

timeout
How long a single RTTMonEcho ICMP 'ping' take at maximum plus 10 seconds to spare.
Since we control our own timeout the only purpose of this is to not have us killed by
the ping method from basefork.

Example value: 15

Default value: 15

tos The (optional) tos parameter specifies the value of the ToS byte in the IP header of
the pings. Multiply DSCP values times 4 and Precedence values times 32 to calculate
the ToS values to configure, e.g. ToS 160 corresponds to a DSCP value 40 and a
Precedence value of 5. The RTTMon MIB versions before IOS 12.0\fIs0(3)T didn't support
this parameter.

Example value: 160

Default value: 0

vrf The the VPN name in which the RTT operation will be used. For regular RTT operation
this field should not be configured. The agent will use this field to identify the VPN
routing Table for this operation.

Example value: INTERNET

AUTHORS

       Joerg.Kummer at Roche.com

NOTES

   IOS VERSIONS
       It is highly recommended to use this probe with routers running IOS 12.0\fIs0(3)T or
       higher and to test it on less critical routers first. I managed to crash a router with
       12.0(9) quite consistently ( in IOS lingo 12.0(9) is older code than 12.0(3)T ). I did not
       observe crashes on higher IOS releases, but messages on the router like the one below,
       when multiple processes concurrently accessed the same router (this case was IOS 12.1(12b)
       ):

       Aug 20 07:30:14: %RTT-3-SemaphoreBadUnlock: %RTR: Attempt to unlock semaphore by wrong RTR
       process 70, locked by 78

       Aug 20 07:35:15: %RTT-3-SemaphoreInUse: %RTR: Could not obtain a lock for RTR. Process 80

   INSTALLATION
       To install this probe copy ciscoRttMonMIB.pm files to ($SMOKEPINGINSTALLDIR)/lib/Smokeping
       and CiscoRTTMonEchoICMP.pm to ($SMOKEPINGINSTALLDIR)/lib/Smokeping/probes. V0.97 or higher
       of Simon Leinen's SNMP_Session.pm is required.

       The router(s) must be configured to allow read/write SNMP access. Sufficient is:

               snmp-server community RTTCommunity RW

       If you want to be a bit more restrictive with SNMP write access to the router, then
       consider configuring something like this

               access-list 2 permit 10.37.3.5
               snmp-server view RttMon ciscoRttMonMIB included
               snmp-server community RTTCommunity view RttMon RW 2

       The above configuration grants SNMP read-write only to 10.37.3.5 (the smokeping host) and
       only to the ciscoRttMon MIB tree. The probe does not need access to SNMP variables outside
       the RttMon tree.

BUGS

       The probe sends unnecessary pings, i.e. more than configured in the "pings" variable,
       because the RTTMon MIB only allows to set a total time for all pings in one measurement
       run (one "life"). Currently the probe sets the life duration to "pings"*5+3 seconds (5
       secs is the ping timeout value hardcoded into this probe).