Provided by: manpages-posix-dev_2013a-1_all 
PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of
this interface may differ (consult the corresponding Linux manual page for details of
Linux behavior), or the interface may not be implemented on Linux.
NAME
msgsnd — XSI message send operation
SYNOPSIS
#include <sys/msg.h>
int msgsnd(int msqid, const void *msgp, size_t msgsz, int msgflg);
DESCRIPTION
The msgsnd() function operates on XSI message queues (see the Base Definitions volume of
POSIX.1‐2008, Section 3.225, Message Queue). It is unspecified whether this function
interoperates with the realtime interprocess communication facilities defined in Section
2.8, Realtime.
The msgsnd() function shall send a message to the queue associated with the message queue
identifier specified by msqid.
The application shall ensure that the argument msgp points to a user-defined buffer that
contains first a field of type long specifying the type of the message, and then a data
portion that holds the data bytes of the message. The structure below is an example of
what this user-defined buffer might look like:
struct mymsg {
long mtype; /* Message type. */
char mtext[1]; /* Message text. */
}
The structure member mtype is a non-zero positive type long that can be used by the
receiving process for message selection.
The structure member mtext is any text of length msgsz bytes. The argument msgsz can range
from 0 to a system-imposed maximum.
The argument msgflg specifies the action to be taken if one or more of the following is
true:
* The number of bytes already on the queue is equal to msg_qbytes; see <sys/msg.h>.
* The total number of messages on all queues system-wide is equal to the system-imposed
limit.
These actions are as follows:
* If (msgflg & IPC_NOWAIT) is non-zero, the message shall not be sent and the calling
thread shall return immediately.
* If (msgflg & IPC_NOWAIT) is 0, the calling thread shall suspend execution until one of
the following occurs:
-- The condition responsible for the suspension no longer exists, in which case the
message is sent.
-- The message queue identifier msqid is removed from the system; when this occurs,
errno shall be set to [EIDRM] and −1 shall be returned.
-- The calling thread receives a signal that is to be caught; in this case the
message is not sent and the calling thread resumes execution in the manner
prescribed in sigaction().
Upon successful completion, the following actions are taken with respect to the data
structure associated with msqid; see <sys/msg.h>:
* msg_qnum shall be incremented by 1.
* msg_lspid shall be set to the process ID of the calling process.
* msg_stime shall be set to the current time, as described in Section 2.7.1, IPC General
Description.
RETURN VALUE
Upon successful completion, msgsnd() shall return 0; otherwise, no message shall be sent,
msgsnd() shall return −1, and errno shall be set to indicate the error.
ERRORS
The msgsnd() function shall fail if:
EACCES Operation permission is denied to the calling process; see Section 2.7, XSI
Interprocess Communication.
EAGAIN The message cannot be sent for one of the reasons cited above and (msgflg &
IPC_NOWAIT) is non-zero.
EIDRM The message queue identifier msqid is removed from the system.
EINTR The msgsnd() function was interrupted by a signal.
EINVAL The value of msqid is not a valid message queue identifier, or the value of mtype
is less than 1; or the value of msgsz is greater than the system-imposed limit.
The following sections are informative.
EXAMPLES
Sending a Message
The following example sends a message to the queue identified by the msqid argument
(assuming that value has previously been set). This call specifies that an error should be
reported if no message is available. The message size is calculated directly using the
sizeof operator.
#include <sys/msg.h>
...
int result;
int msqid;
struct message {
long type;
char text[20];
} msg;
msg.type = 1;
strcpy(msg.text, "This is message 1");
...
result = msgsnd(msqid, (void *) &msg, sizeof(msg.text), IPC_NOWAIT);
APPLICATION USAGE
The POSIX Realtime Extension defines alternative interfaces for interprocess communication
(IPC). Application developers who need to use IPC should design their applications so that
modules using the IPC routines described in Section 2.7, XSI Interprocess Communication
can be easily modified to use the alternative interfaces.
RATIONALE
None.
FUTURE DIRECTIONS
None.
SEE ALSO
Section 2.7, XSI Interprocess Communication, Section 2.8, Realtime, mq_close(),
mq_getattr(), mq_notify(), mq_open(), mq_receive(), mq_send(), mq_setattr(), mq_unlink(),
msgctl(), msgget(), msgrcv(), sigaction()
The Base Definitions volume of POSIX.1‐2008, Section 3.225, Message Queue, <sys_msg.h>
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std
1003.1, 2013 Edition, Standard for Information Technology -- Portable Operating System
Interface (POSIX), The Open Group Base Specifications Issue 7, Copyright (C) 2013 by the
Institute of Electrical and Electronics Engineers, Inc and The Open Group. (This is
POSIX.1-2008 with the 2013 Technical Corrigendum 1 applied.) In the event of any
discrepancy between this version and the original IEEE and The Open Group Standard, the
original IEEE and The Open Group Standard is the referee document. The original Standard
can be obtained online at http://www.unix.org/online.html .
Any typographical or formatting errors that appear in this page are most likely to have
been introduced during the conversion of the source files to man page format. To report
such errors, see https://www.kernel.org/doc/man-pages/reporting_bugs.html .