Provided by: freebsd-manpages_10.1~RC1-1_all bug

NAME

     twe — 3ware 5000/6000/7000/8000 series PATA/SATA RAID adapter driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device pci
           device twe

     Alternatively, to load the driver as a module at boot time, place the following line in
     loader.conf(5):

           twe_load="YES"

DESCRIPTION

     The twe driver provides support for AMCC's 3ware 5000/6000/7000/8000 series PATA/SATA RAID
     adapters.  These adapters were formerly known as “3ware Escalade”.

     These devices support 2, 4, 8, or 12 ATA disk drives and provide RAID0 (striping) and RAID1
     (mirroring) functionality.

HARDWARE

     The twe driver supports the following PATA/SATA RAID controllers:

        AMCC's 3ware 5000 series
        AMCC's 3ware 6000 series
        AMCC's 3ware 7000-2
        AMCC's 3ware 7006-2
        AMCC's 3ware 7500-4LP
        AMCC's 3ware 7500-8
        AMCC's 3ware 7500-12
        AMCC's 3ware 7506-4LP
        AMCC's 3ware 7506-8
        AMCC's 3ware 7506-12
        AMCC's 3ware 8006-2LP
        AMCC's 3ware 8500-4LP
        AMCC's 3ware 8500-8
        AMCC's 3ware 8500-12
        AMCC's 3ware 8506-4LP
        AMCC's 3ware 8506-8
        AMCC's 3ware 8506-8MI
        AMCC's 3ware 8506-12
        AMCC's 3ware 8506-12MI

DIAGNOSTICS

   Controller initialisation phase
     twe%d: microcontroller not ready

     The controller's onboard CPU is not reporting that it is ready; this may be due to either a
     board or system failure.  Initialisation has failed.

     twe%d: no attention interrupt
     twe%d: can't drain AEN queue
     twe%d: reset not reported
     twe%d: controller errors detected
     twe%d: can't drain response queue
     twe%d: reset %d failed, trying again

     The controller is not responding correctly to the driver's attempts to reset and initialise
     it.  This process is retried several times.

     twe%d: can't initialise controller, giving up

     Several attempts to reset and initialise the controller have failed; initialisation has
     failed and the driver will not attach to this controller.

   Driver initialisation/shutdown phase
     twe%d: register window not available
     twe%d: can't allocate register window
     twe%d: can't allocate parent DMA tag
     twe%d: can't allocate interrupt
     twe%d: can't set up interrupt
     twe%d: can't establish configuration hook

     A resource allocation error occurred while initialising the driver; initialisation has
     failed and the driver will not attach to this controller.

     twe%d: can't detect attached units

     Fetching the list of attached units failed; initialisation has failed.

     twe%d: error fetching capacity for unit %d
     twe%d: error fetching state for unit %d
     twe%d: error fetching descriptor size for unit %d
     twe%d: error fetching descriptor for unit %d
     twe%d: device_add_child failed
     twe%d: bus_generic_attach returned %d

     Creation of the disk devices failed, either due to communication problems with the adapter
     or due to resource shortage; attachment of one or more units may have been aborted.

   Operational phase
     twe%d: command completed - %s

     A command was reported completed with a warning by the controller.  The warning may be one
     of:

     redundant/inconsequential request ignored
     failed to write zeroes to LBA 0
     failed to profile TwinStor zones

     twe%d: command failed - %s

     A command was reported as failed by the controller.  The failure message may be one of:

     aborted due to system command or reconfiguration
     aborted
     access error
     access violation
     device failure
     controller error
     timed out
     invalid unit number
     unit not available
     undefined opcode
     request incompatible with unit
     invalid request
     firmware error, reset requested

     The command will be returned to the operating system after a fatal error.

     twe%d: command failed submission - controller wedged

     A command could not be delivered to the controller because the controller is unresponsive.

     twe%d: AEN: <%s>

     The controller has reported a change in status using an AEN (Asynchronous Event
     Notification).  The following AENs may be reported:

     queue empty
     soft reset
     degraded mirror
     controller error
     rebuild fail
     rebuild done
     incomplete unit
     initialisation done
     unclean shutdown detected
     drive timeout
     drive error
     rebuild started
     aen queue full

     AENs are also queued internally for use by management tools.

     twe%d: error polling for signalled AENs

     The controller has reported that one or more status messages are ready for the driver, but
     attempting to fetch one of these has returned an error.

     twe%d: AEN queue overflow, lost AEN <%s>

     A status message was retrieved from the controller, but there is no more room to queue it in
     the driver.  The message is lost (but will be printed to the console).

     twe%d: missing expected status bits %s
     twe%d: unexpected status bits %s

     A check of the controller's status bits indicates an unexpected condition.

     twe%d: host interrupt

     The controller has signalled a host interrupt.  This serves an unknown purpose and is
     ignored.

     twe%d: command interrupt

     The controller has signalled a command interrupt.  This is not used, and will be disabled.

     twe%d: controller reset in progress...

     The controller is being reset by the driver.  Typically this is done when the driver has
     determined that the controller is in an unrecoverable state.

     twe%d: can't reset controller, giving up

     The driver has given up on resetting the controller.  No further I/O will be handled.

     controller reset done, %d commands restarted

     The controller was successfully reset, and outstanding commands were restarted.

AUTHORS

     The twe driver and manual page were written by Michael Smith ⟨msmith@FreeBSD.org⟩.

     Extensive work done on the driver by Vinod Kashyap ⟨vkashyap@FreeBSD.org⟩ and Paul Saab
     ⟨ps@FreeBSD.org⟩.

BUGS

     The controller cannot handle I/O transfers that are not aligned to a 512-byte boundary.  In
     order to support raw device access from user-space, the driver will perform alignment fixup
     on non-aligned data.  This process is inefficient, and thus in order to obtain best
     performance user-space applications accessing the device should do so with aligned buffers.