Provided by: ipmiutil_2.9.7-1_i386 bug


       ipmiutil_picmg - send specific PICMG extended IPMI commands


       ipmiutil picmg [-mixNUPREFJTVY] parameters


       This  ipmiutil picmg subcommand sends specific PICMG/ATCA extended IPMI
       commands to the firmware.

       This utility can use either the /dev/ipmi0 driver  from  OpenIPMI,  the
       /dev/imb  driver  from  Intel,  the  /dev/ipmikcs  driver from valinux,
       direct user-space IOs, or the IPMI LAN interface if -N.


       Command line options are described below.

       -i 00  This option specifies a specific FRU  ID  to  show.   The  input
              value  should be in hex (0b, 1a, etc.), as shown from the sensor
              SDR output.  The default FRU ID is zero (0).

       -m 002000
              Show FRU for a specific MC (e.g. bus 00, sa 20, lun  00).   This
              could  be  used  for  PICMG or ATCA blade systems.  The trailing
              character, if present, indicates SMI addressing if 's', or  IPMB
              addressing if 'i' or not present.

       -x     Causes extra debug messages to be displayed.

       -N nodename
              Nodename  or  IP  address  of  the  remote  target system.  If a
              nodename is specified, IPMI LAN interface  is  used.   Otherwise
              the local system management interface is used.

       -U rmt_user
              Remote  username  for the nodename given.  The default is a null

       -P/-R rmt_pswd
              Remote password for the nodename given.  The default is  a  null

       -E     Use the remote password from Environment variable IPMI_PASSWORD.

       -F drv_t
              Force  the  driver  type  to one of the followng: imb, va, open,
              gnu, landesk, lan, lan2, lan2i, kcs, smb.  Note that lan2i means
              lan2  with  intelplus.   The  default is to detect any available
              driver type and use it.

       -J     Use  the  specified  LanPlus   cipher   suite   (0   thru   17):
              0=none/none/none,       1=sha1/none/none,      2=sha1/sha1/none,
              3=sha1/sha1/cbc128,  4=sha1/sha1/xrc4_128,  5=sha1/sha1/xrc4_40,
              6=md5/none/none, ... 14=md5/md5/xrc4_40.  Default is 3.

       -T     Use  a  specified  IPMI  LAN Authentication Type: 0=None, 1=MD2,
              2=MD5, 4=Straight Password, 5=OEM.

       -V     Use a specified IPMI  LAN  privilege  level.  1=Callback  level,
              2=User level, 3=Operator level, 4=Administrator level (default),
              5=OEM level.

       -Y     Yes, do prompt the  user  for  the  IPMI  LAN  remote  password.
              Alternatives for the password are -E or -P.


       picmg parameters

                     Get  PICMG  properties  may  be  used to obtain and print
                     Extension major version  information,  PICMG  identifier,
                     FRU Device ID and Max FRU Device ID.


                     Get   address   information.   This  command  may  return
                     information on the Hardware address, IPMB-0 Address,  FRU
                     ID, Site/Entity ID, and Site/Entity Type.

              frucontrol fru id options

                     Set various control options:

                     0x00      - Cold Reset

                     0x01      - Warm Reset

                     0x02      - Graceful Reboot

                     0x03      - Issue Diagnostic Interrupt

                     0x04      - Quiesce [AMC only]

                     0x05-0xFF - Cold Reset

              activate fru id

                     Activate the specified FRU.

              deactivate fru id

                     Deactivate the specified FRU.

              policy get fru id

                     Get FRU activation policy.

              policy set fru id lockmask lock

                     Set  FRU  activation  policy.   lockmask  is  1  or  0 to
                     indicate action on the deactivation or activation  locked
                     bit  respectively.   lock  is  1 or 0 to set/clear locked

              portstate set|getall|getgranted|getdenied parameters

                     Get or set various port states.  See usage for  parameter


       ipmiutil picmg properties
       Gets  PICMG  properties  from the default target address (slave address

       ipmiutil picmg -N -U root -P pswd addrinfo
       Gets PICMG Address Information from the specified IP address.


       ipmiutil(8)  ialarms(8)  iconfig(8)  idiscover(8)  ievents(8)   ifru(8)
       igetevent(8) ihealth(8) ilan(8) ireset(8) isel(8) isensor(8) iserial(8)
       isol(8) iwdt(8)


       See for the latest version of ipmiutil
       and any bug fix list.


       Copyright (C) 2010  Kontron America, Inc.

       See  the  file  COPYING  in the distribution for more details regarding

       This utility is distributed in the hope that it  will  be  useful,  but


       Andy Cress <arcress at>

                           Version 1.0: 04 Jun 2010                  IPICMG(8)