Provided by: watchdog_5.15-2_amd64 
NAME
watchdog - a software watchdog daemon
SYNOPSIS
watchdog [-F|--foreground] [-f|--force] [-c filename|--config-file filename] [-v|--verbose] [-s|--sync]
[-b|--softboot] [-q|--no-action]
DESCRIPTION
The Linux kernel can reset the system if serious problems are detected. This can be implemented via
special watchdog hardware, or via a slightly less reliable software-only watchdog inside the kernel.
Either way, there needs to be a daemon that tells the kernel the system is working fine. If the daemon
stops doing that, the system is reset.
watchdog is such a daemon. It opens /dev/watchdog, and keeps writing to it often enough to keep the
kernel from resetting, at least once per minute. Each write delays the reboot time another minute. After
a minute of inactivity the watchdog hardware will cause the reset. In the case of the software watchdog
the ability to reboot will depend on the state of the machines and interrupts.
The watchdog daemon can be stopped without causing a reboot if the device /dev/watchdog is closed
correctly, unless your kernel is compiled with the CONFIG_WATCHDOG_NOWAYOUT option enabled.
TESTS
The watchdog daemon does several tests to check the system status:
• Is the process table full?
• Is there enough free memory?
• Is there enough allocatable memory?
• Are some files accessible?
• Have some files changed within a given interval?
• Is the average work load too high?
• Has a file table overflow occurred?
• Is a process still running? The process is specified by a pid file.
• Do some IP addresses answer to ping?
• Do network interfaces receive traffic?
• Is the temperature too high? (Temperature data not always available.)
• Execute a user defined command to do arbitrary tests.
• Execute one or more test/repair commands found in /etc/watchdog.d. These commands are called with the
argument test or repair.
If any of these checks fail watchdog will cause a shutdown. Should any of these tests except the user
defined binary last longer than one minute the machine will be rebooted, too.
OPTIONS
Available command line options are the following:
-v, --verbose
Set verbose mode. Only implemented if compiled with SYSLOG feature. This mode will log each
several infos in LOG_DAEMON with priority LOG_DEBUG. This is useful if you want to see exactly
what happened until the watchdog rebooted the system. Currently it logs the temperature (if
available), the load average, the change date of the files it checks and how often it went to
sleep.
-s, --sync
Try to synchronize the filesystem every time the process is awake. Note that the system is
rebooted if for any reason the synchronizing lasts longer than a minute.
-b, --softboot
Soft-boot the system if an error occurs during the main loop, e.g. if a given file is not
accessible via the stat(2) call. Note that this does not apply to the opening of /dev/watchdog and
/proc/loadavg, which are opened before the main loop starts. Now this is implemented by disabling
the error re-try timer.
-F, --foreground
Run in foreground mode, useful for running under systemd (for example).
-f, --force
Force the usage of the interval given or the maximal load average given in the config file.
Without this option these values are sanity checked.
-c config-file, --config-file config-file
Use config-file as the configuration file instead of the default /etc/watchdog.conf.
-q, --no-action
Do not reboot or halt the machine. This is for testing purposes. All checks are executed and the
results are logged as usual, but no action is taken. Also your hardware card or the kernel
software watchdog driver is not enabled. NOTE: This still allows 'repair' actions to run, but the
daemon itself will not attempt a reboot.
-X num, --loop-exit num
Run for 'num' loops then exit as if SIGTERM was received. Intended for test/debug (e.g. using
valgrind for checking memory access). If the daemon exits on a loop counter and you have the
CONFIG_WATCHDOG_NOWAYOUT option compiled for the kernel or device-driver then an unplanned reboot
will follow - be warned!
FUNCTION
After watchdog starts, it puts itself into the background and then tries all checks specified in its
configuration file in turn. Between each two tests it will write to the kernel device to prevent a reset.
After finishing all tests watchdog goes to sleep for some time. The kernel drivers expects a write to the
watchdog device every minute. Otherwise the system will be reset. watchdog will sleep for a configure
interval that defaults to 1 second to make sure it triggers the device early enough.
Under high system load watchdog might be swapped out of memory and may fail to make it back in in time.
Under these circumstances the Linux kernel will reset the machine. To make sure you won't get unnecessary
reboots make sure you have the variable realtime set to yes in the configuration file watchdog.conf.
This adds real time support to watchdog: it will lock itself into memory and there should be no problem
even under the highest of loads.
On system running out of memory the kernel will try to free enough memory by killing process. The
watchdog daemon itself is exempted from this so-called out-of-memory killer.
Also you can specify a maximal allowed load average. Once this load average is reached the system is
rebooted. You may specify maximal load averages for 1 minute, 5 minutes or 15 minutes. The default values
is to disable this test. Be careful not to set this parameter too low. To set a value less then the
predefined minimal value of 2, you have to use the -f option.
You can also specify a minimal amount of virtual memory you want to have available as free. As soon as
more virtual memory is used action is taken by watchdog. Note, however, that watchdog does not
distinguish between different types of memory usage. It just checks for free virtual memory.
If you have a machine with temperature sensor(s) you can specify the maximal allowed temperature. Once
this temperature is reached on any sensor the system is powered off. The default value is 90 C. Typically
the temperature information is provided by the sensors package as files in the virtual filesystem
/sys/device and can be found using, for example, the command
find /sys -name 'temp*input' -print
These files hold the temperature in milli-Celsius. You can have multiple sensors used in the config file.
For example to change to 75C maximum and to check two virtual files for the system temperature you might
have this:
max-temperature = 75
temperature-sensor = /sys/class/hwmon/hwmon0/device/temp1_input
temperature-sensor = /sys/class/hwmon/hwmon0/device/temp2_input
The watchdog will issue warnings once the temperature increases 90%, 95% and 98% of the configured
maximum temperature.
When using file mode watchdog will try to stat(2) the given files. Errors returned by stat will not cause
a reboot. For a reboot the stat call has to last at least the re-try time-out value (default 1 minute).
This may happen if the file is located on an NFS mounted filesystem. If your system relies on an NFS
mounted filesystem you might try this option. However, in such a case the sync option may not work if
the NFS server is not answering.
watchdog can read the pid from a pid file and see whether the process still exists. If not, action is
taken by watchdog. So you can for instance restart the server from your repair-binary.
watchdog will try periodically to fork itself to see whether the process table is full. This process will
leave a zombie process until watchdog wakes up again and catches it; this is harmless, don't worry about
it.
In ping mode watchdog tries to ping the given IPv4 addresses. These addresses do not have to be a single
machine. It is possible to ping to a broadcast address instead to see if at least one machine in a subnet
is still living.
Do not use this broadcast ping unless your MIS person a) knows about it and b) has given you explicit
permission to use it!
watchdog will send out three ping packages and wait up to <interval> seconds for the reply with
<interval> being the time it goes to sleep between two times triggering the watchdog device. Thus a
unreachable network will not cause a hard reset but a soft reboot.
You can also test passively for an unreachable network by just monitoring a given interface for traffic.
If no traffic arrives the network is considered unreachable causing a soft reboot or action from the
repair binary.
watchdog can run an external command for user-defined tests. A return code not equal 0 means an error
occurred and watchdog should react. If the external command is killed by an uncaught signal this is
considered an error by watchdog too. The command may take longer than the time slice defined for the
kernel device without a problem. However, error messages are generated into the syslog facility. If you
have enabled softboot on error the machine will be rebooted if the binary doesn't exit in half the time
watchdog sleeps between two tries triggering the kernel device.
If you specify a repair binary it will be started instead of shutting down the system. If this binary is
not able to fix the problem watchdog will still cause a reboot afterwards.
If the machine is halted an email is sent to notify a human that the machine is going down. Starting with
version 4.4 watchdog will also notify the human in charge if the machine is rebooted.
The re-try timer applies to most errors, except reset/reboot calls and too hot. It allows a given error
source to recover, and treats most tests in this way. Exceptions are file handle test, load averages,
and system memory. If set to the minimum time of 1 second it will still allow a single re-try at any
polling interval of the system.
SOFT REBOOT
A soft reboot (i.e. controlled shutdown and reboot) is initiated for every error that is found. Since
there might be no more processes available, watchdog does it all by himself. That means:
1. Kill all processes with SIGTERM.
2. After a short pause kill all remaining processes with SIGKILL.
3. Record a shutdown entry in wtmp.
4. Save the random seed from /dev/urandom. If the device is non-existant or there is no filename for
saving this step is skipped.
5. Turn off accounting.
6. Turn off quota and swap.
7. Unmount all partitions except the root partition.
8. Remount the root partition read-only.
9. Shut down all network interfaces.
10. Finally reboot.
CHECK BINARY
If the return code of the check binary is not zero watchdog will assume an error and reboot the system.
Be careful with this if you are using the real-time properties of watchdog since watchdog will wait for
the return of this binary before proceeding. An exit code smaller than 245 is interpreted as an system
error code (see errno.h for details). Values of 245 or larger than are special to watchdog:
255 (based on -1 as unsigned 8-bit number)
Reboot the system. This is not exactly an error message but a command to watchdog. If the return
code is this the watchdog will not try to run a shutdown script instead.
254 Reset the system. This is not exactly an error message but a command to watchdog. If the return
code is this the watchdog will attempt to hard-reset the machine without attempting any sort of
orderly stopping of process, unmounting of file systems, etc.
253 Maximum load average exceeded.
252 The temperature inside is too high.
251 /proc/loadavg contains no (or not enough) data.
250 The given file was not changed in the given interval.
249 /proc/meminfo contains invalid data.
248 Child process was killed by a signal.
247 Child process did not return in time.
246 Free for personal watchdog-specific use (was -10 as an unsigned 8-bit number).
245 Reserved for an unknown result, for example a slow background test that is still running so
neither a success nor an error.
REPAIR BINARY
The repair binary is started with one parameter: the error number that caused watchdog to initiate the
boot process. After trying to repair the system the binary should exit with 0 if the system was
successfully repaired and thus there is no need to boot anymore. A return value not equal 0 tells
watchdog to reboot. The return code of the repair binary should be the error number of the error causing
watchdog to reboot. Be careful with this if you are using the real-time properties since watchdog will
wait for the return of this binary before proceeding.
The configuration file parameter repair-maximum controls the number of successive repair attempts that
report 0 (i.e. success) but fail to clear the tested fault. If this is exceeded then a reboot takes
place. If set to zero then a reboot can always be blocked by the repair program reporting success.
TEST DIRECTORY
Executables placed in the test directory are discovered by watchdog on startup and are automatically
executed. They are bounded time-wise by the test-timeout directive in watchdog.conf.
These executables are called with either "test" as the first argument (if a test is being performed) or
"repair" as the first argument (if a repair for a previously-failed "test" operation on is being
performed).
The as with test binaries and repair binaries, expected exit codes for a successful test or repair
operation is always zero.
If an executable's test operation fails, the same executable is automatically called with the "repair"
argument as well as the return code of the previously-failed test operation.
For example, if the following execution returns 42:
/etc/watchdog.d/my-test test
The watchdog daemon will attempt to repair the problem by calling:
/etc/watchdog.d/my-test repair 42
This enables administrators and application developers to make intelligent test/repair commands. If the
"repair" operation is not required (or is not likely to succeed), it is important that the author of the
command return a non-zero value so the machine will still reboot as expected.
Note that the watchdog daemon may interpret and act upon any of the reserved return codes noted in the
Check Binary section prior to calling a given command in "repair" mode.
As for the repair binary, the configuration parameter repair-maximum also controls the number of
successive repair attempts that report success (return 0) but fail to clear the fault.
BUGS
None known so far.
AUTHORS
The original code is an example written by Alan Cox <alan@lxorguk.ukuu.org.uk>, the author of the kernel
driver. All additions were written by Michael Meskes <meskes@debian.org>. Johnie Ingram
<johnie@netgod.net> had the idea of testing the load average. He also took over the Debian specific work.
Dave Cinege <dcinege@psychosis.com> brought up some hardware watchdog issues and helped testing this
stuff.
FILES
/dev/watchdog
The watchdog device.
/var/run/watchdog.pid
The pid file of the running watchdog.
SEE ALSO
watchdog.conf(5)
4th Berkeley Distribution January 2016 WATCHDOG(8)