Provided by: pcp_4.0.1-1_amd64 
NAME
pcp-atop, pmatop - Advanced System and Process Monitor
SYNOPSIS
Interactive Usage:
pcp [pcp options] atop [-g|-m|-d|-n|-u|-p|-s|-c|-v|-o|-y] [-C|-M|-D|-N|-A] [-afFG1xR] [-L
linelen] [-Plabel[,label]...] [interval [samples]]
Writing and reading raw logfiles:
pcp atop -w rawfile [-a] [-S] [interval [samples]]
pcp atop -r [ rawfile ] [-b hh:mm ] [-e hh:mm ] [-g|-m|-d|-n|-u|-p|-s|-c|-v|-o|-y]
[-C|-M|-D|-N|-A] [-fFG1xR] [-L linelen] [-Plabel[,label]...]
DESCRIPTION
The program pcp-atop is an interactive monitor to view various aspects of load on a
system. It shows the occupation of the most critical hardware resources (from a
performance point of view) on system level, i.e. cpu, memory, disk and network.
It also shows which processes are responsible for the indicated load with respect to cpu
and memory load on process level. Disk load is shown per process if "storage accounting"
is active in the kernel.
Every interval (default: 10 seconds) information is shown about the resource occupation on
system level (cpu, memory, disks and network layers), followed by a list of processes
which have been active during the last interval (note that all processes that were
unchanged during the last interval are not shown, unless the key 'a' has been pressed or
unless sorting on memory occupation is done). If the list of active processes does not
entirely fit on the screen, only the top of the list is shown (sorted in order of
activity).
The intervals are repeated till the number of samples (specified as command argument) is
reached, or till the key 'q' is pressed in interactive mode.
When invoked via the pcp(1) command, the PCPIntro(1) options -h/--host, -a/--archive,
-O/--origin, -s/--samples, -t/--interval, -Z/--timezone and several other pcp options
become indirectly available. The long option form of these is directly available.
Additionally, the --hotproc option can be used to request the per-process PCP metrics be
used instead of the default proc metrics from pmdaproc(1).
When pcp-atop is started, it checks whether the standard output channel is connected to a
screen, or to a file/pipe. In the first case it produces screen control codes (via the
ncurses library) and behaves interactively; in the second case it produces flat ASCII-
output.
In interactive mode, the output of pcp-atop scales dynamically to the current dimensions
of the screen/window.
If the window is resized horizontally, columns will be added or removed automatically. For
this purpose, every column has a particular weight. The columns with the highest weights
that fit within the current width will be shown.
If the window is resized vertically, lines of the process/thread list will be added or
removed automatically.
Furthermore in interactive mode the output of pcp-atop can be controlled by pressing
particular keys. However it is also possible to specify such key as flag on the command
line. In that case pcp-atop switches to the indicated mode on beforehand; this mode can be
modified again interactively. Specifying such key as flag is especially useful when
running pcp-atop with output to a pipe or file (non-interactively). These flags are the
same as the keys that can be pressed in interactive mode (see section INTERACTIVE
COMMANDS).
Additional flags are available to support storage of pcp-atop data in PCP archive format
(see section PCP DATA STORAGE).
COLORS
For the resource consumption on system level, pcp-atop uses colors to indicate that a
critical occupation percentage has been (almost) reached. A critical occupation
percentage means that is likely that this load causes a noticeable negative performance
influence for applications using this resource. The critical percentage depends on the
type of resource: e.g. the performance influence of a disk with a busy percentage of 80%
might be more noticeable for applications/user than a CPU with a busy percentage of 90%.
Currently pcp-atop uses the following default values to calculate a weighted percentage
per resource:
Processor
A busy percentage of 90% or higher is considered `critical'.
Disk
A busy percentage of 70% or higher is considered `critical'.
Network
A busy percentage of 90% or higher for the load of an interface is considered
`critical'.
Memory
An occupation percentage of 90% is considered `critical'. Notice that this
occupation percentage is the accumulated memory consumption of the kernel (including
slab) and all processes; the memory for the page cache (`cache' and `buff' in the
MEM-line) and the reclaimable part of the slab (`slrec`) is not implied!
If the number of pages swapped out (`swout' in the PAG-line) is larger than 10 per
second, the memory resource is considered `critical'. A value of at least 1 per
second is considered `almost critical'.
If the committed virtual memory exceeds the limit (`vmcom' and `vmlim' in the SWP-
line), the SWP-line is colored due to overcommitting the system.
Swap
An occupation percentage of 80% is considered `critical' because swap space might be
completely exhausted in the near future; it is not critical from a performance point-
of-view.
These default values can be modified in the configuration file (see separate man-page of
pcp-atoprc).
When a resource exceeds its critical occupation percentage, the concerning values in the
screen line are colored red by default.
When a resource exceeded (default) 80% of its critical percentage (so it is almost
critical), the concerning values in the screen line are colored cyan by default. This
`almost critical percentage' (one value for all resources) can be modified in the
configuration file (see separate man-page of pcp-atoprc).
The default colors red and cyan can be modified in the configuration file as well (see
separate man-page of pcp-atoprc).
With the key 'x' (or flag -x), the use of colors can be suppressed.
INTERACTIVE COMMANDS
When running pcp-atop interactively (no output redirection), keys can be pressed to
control the output. In general, lower case keys can be used to show other information for
the active processes and upper case keys can be used to influence the sort order of the
active process/thread list.
g Show generic output (default).
Per process the following fields are shown in case of a window-width of 80 positions:
process-id, cpu consumption during the last interval in system and user mode, the
virtual and resident memory growth of the process.
The subsequent columns depend on the used kernel:
When the kernel supports "storage accounting" (>= 2.6.20), the data transfer for
read/write on disk, the status and exit code are shown for each process. When the
kernel does not support "storage accounting", the username, number of threads in the
thread group, the status and exit code are shown.
The last columns contain the state, the occupation percentage for the chosen resource
(default: cpu) and the process name.
When more than 80 positions are available, other information is added.
m Show memory related output.
Per process the following fields are shown in case of a window-width of 80 positions:
process-id, minor and major memory faults, size of virtual shared text, total virtual
process size, total resident process size, virtual and resident growth during last
interval, memory occupation percentage and process name.
When more than 80 positions are available, other information is added.
For memory consumption, always all processes are shown (also the processes that were
not active during the interval).
d Show disk-related output.
When "storage accounting" is active in the kernel, the following fields are shown:
process-id, amount of data read from disk, amount of data written to disk, amount of
data that was written but has been withdrawn again (WCANCL), disk occupation
percentage and process name.
s Show scheduling characteristics.
Per process the following fields are shown in case of a window-width of 80 positions:
process-id, number of threads in state 'running' (R), number of threads in state
'interruptible sleeping' (S), number of threads in state 'uninterruptible sleeping'
(D), scheduling policy (normal timesharing, realtime round-robin, realtime fifo),
nice value, priority, realtime priority, current processor, status, exit code, state,
the occupation percentage for the chosen resource and the process name.
When more than 80 positions are available, other information is added.
v Show various process characteristics.
Per process the following fields are shown in case of a window-width of 80 positions:
process-id, user name and group, start date and time, status (e.g. exit code if the
process has finished), state, the occupation percentage for the chosen resource and
the process name.
When more than 80 positions are available, other information is added.
c Show the command line of the process.
Per process the following fields are shown: process-id, the occupation percentage for
the chosen resource and the command line including arguments.
o Show the user-defined line of the process.
In the configuration file the keyword ownprocline can be specified with the
description of a user-defined output-line.
Refer to the man-page of pcp-atoprc for a detailed description.
y Show the individual threads within a process (toggle).
Single-threaded processes are still shown as one line.
For multi-threaded processes, one line represents the process while additional lines
show the activity per individual thread (in a different color). Depending on the
option 'a' (all or active toggle), all threads are shown or only the threads that
were active during the last interval.
Whether this key is active or not can be seen in the header line.
u Show the process activity accumulated per user.
Per user the following fields are shown: number of processes active or terminated
during last interval (or in total if combined with command `a'), accumulated cpu
consumption during last interval in system and user mode, the current virtual and
resident memory space consumed by active processes (or all processes of the user if
combined with command `a').
When "storage accounting" is active in the kernel, the accumulated read and write
throughput on disk is shown. When the kernel module `netatop' has been installed,
the number of received and sent network packets are shown.
The last columns contain the accumulated occupation percentage for the chosen
resource (default: cpu) and the user name.
p Show the process activity accumulated per program (i.e. process name).
Per program the following fields are shown: number of processes active or terminated
during last interval (or in total if combined with command `a'), accumulated cpu
consumption during last interval in system and user mode, the current virtual and
resident memory space consumed by active processes (or all processes of the user if
combined with command `a').
When "storage accounting" is active in the kernel, the accumulated read and write
throughput on disk is shown. When the kernel module `netatop' has been installed,
the number of received and sent network packets are shown.
The last columns contain the accumulated occupation percentage for the chosen
resource (default: cpu) and the program name.
j Show the process activity accumulated per Docker container.
Per container the following fields are shown: number of processes active or
terminated during last interval (or in total if combined with command `a'),
accumulated cpu consumption during last interval in system and user mode, the current
virtual and resident memory space consumed by active processes (or all processes of
the user if combined with command `a').
When "storage accounting" is active in the kernel, the accumulated read and write
throughput on disk is shown. When the kernel module `netatop' has been installed,
the number of received and sent network packets are shown.
The last columns contain the accumulated occupation percentage for the chosen
resource (default: cpu) and the Docker container id (CID).
C Sort the current list in the order of cpu consumption (default). The one-but-last
column changes to ``CPU''.
M Sort the current list in the order of resident memory consumption. The one-but-last
column changes to ``MEM''. In case of sorting on memory, the full process list will
be shown (not only the active processes).
D Sort the current list in the order of disk accesses issued. The one-but-last column
changes to ``DSK''.
N Sort the current list in the order of network bandwidth (received and transmitted).
The one-but-last column changes to ``NET''.
A Sort the current list automatically in the order of the most busy system resource
during this interval. The one-but-last column shows either ``ACPU'', ``AMEM'',
``ADSK'' or ``ANET'' (the preceding 'A' indicates automatic sorting-order). The most
busy resource is determined by comparing the weighted busy-percentages of the system
resources, as described earlier in the section COLORS.
This option remains valid until another sorting-order is explicitly selected again.
A sorting-order for disk is only possible when "storage accounting" is active. A
sorting-order for network is only possible when the kernel module `netatop' is
loaded.
Miscellaneous interactive commands:
? Request for help information (also the key 'h' can be pressed).
V Request for version information (version number and date).
R Gather and calculate the proportional set size of processes (toggle). Gathering of
all values that are needed to calculate the PSIZE of a process is a relatively time-
consuming task, so this key should only be active when analyzing the resident memory
consumption of processes.
x Suppress colors to highlight critical resources (toggle).
Whether this key is active or not can be seen in the header line.
z The pause key can be used to freeze the current situation in order to investigate the
output on the screen. While pcp-atop is paused, the keys described above can be
pressed to show other information about the current list of processes. Whenever the
pause key is pressed again, pcp-atop will continue with a next sample.
i Modify the interval timer (default: 10 seconds). If an interval timer of 0 is
entered, the interval timer is switched off. In that case a new sample can only be
triggered manually by pressing the key 't'.
t Trigger a new sample manually. This key can be pressed if the current sample should
be finished before the timer has exceeded, or if no timer is set at all (interval
timer defined as 0). In the latter case pcp-atop can be used as a stopwatch to
measure the load being caused by a particular application transaction, without
knowing on beforehand how many seconds this transaction will last.
When viewing the contents of a raw file, this key can be used to show the next sample
from the file.
T When viewing the contents of a raw file, this key can be used to show the previous
sample from the file.
b When viewing the contents of a raw file, this key can be used to branch to a certain
timestamp within the file (either forward or backward).
r Reset all counters to zero to see the system and process activity since boot again.
When viewing the contents of a raw file, this key can be used to rewind to the
beginning of the file again.
U Specify a search string for specific user names as a regular expression. From now
on, only (active) processes will be shown from a user which matches the regular
expression. The system statistics are still system wide. If the Enter-key is
pressed without specifying a name, (active) processes of all users will be shown
again.
Whether this key is active or not can be seen in the header line.
I Specify a list with one or more PIDs to be selected. From now on, only processes
will be shown with a PID which matches one of the given list. The system statistics
are still system wide. If the Enter-key is pressed without specifying a PID, all
(active) processes will be shown again.
Whether this key is active or not can be seen in the header line.
P Specify a search string for specific process names as a regular expression. From now
on, only processes will be shown with a name which matches the regular expression.
The system statistics are still system wide. If the Enter-key is pressed without
specifying a name, all (active) processes will be shown again.
Whether this key is active or not can be seen in the header line.
/ Specify a specific command line search string as a regular expression. From now on,
only processes will be shown with a command line which matches the regular
expression. The system statistics are still system wide. If the Enter-key is
pressed without specifying a string, all (active) processes will be shown again.
Whether this key is active or not can be seen in the header line.
J Specify a Docker container id of 12 (hexadecimal) characters. From now on, only
processes will be shown that run in that specific Docker container (CID). The system
statistics are still system wide. If the Enter-key is pressed without specifying a
container id, all (active) processes will be shown again.
Whether this key is active or not can be seen in the header line.
S Specify search strings for specific logical volume names, specific disk names and
specific network interface names. All search strings are interpreted as a regular
expressions. From now on, only those system resources are shown that match the
concerning regular expression. If the Enter-key is pressed without specifying a
search string, all (active) system resources of that type will be shown again.
Whether this key is active or not can be seen in the header line.
a The `all/active' key can be used to toggle between only showing/accumulating the
processes that were active during the last interval (default) or showing/accumulating
all processes.
Whether this key is active or not can be seen in the header line.
G By default, pcp-atop shows/accumulates the processes that are alive and the processes
that are exited during the last interval. With this key (toggle),
showing/accumulating the processes that are exited can be suppressed.
Whether this key is active or not can be seen in the header line.
f Show a fixed (maximum) number of header lines for system resources (toggle). By
default only the lines are shown about system resources (CPUs, paging, logical
volumes, disks, network interfaces) that really have been active during the last
interval. With this key you can force pcp-atop to show lines of inactive resources
as well.
Whether this key is active or not can be seen in the header line.
F Suppress sorting of system resources (toggle). By default system resources (CPUs,
logical volumes, disks, network interfaces) are sorted on utilization.
Whether this key is active or not can be seen in the header line.
1 Show relevant counters as an average per second (in the format `..../s') instead of
as a total during the interval (toggle).
Whether this key is active or not can be seen in the header line.
l Limit the number of system level lines for the counters per-cpu, the active disks and
the network interfaces. By default lines are shown of all CPUs, disks and network
interfaces which have been active during the last interval. Limiting these lines can
be useful on systems with huge number CPUs, disks or interfaces in order to be able
to run pcp-atop on a screen/window with e.g. only 24 lines.
For all mentioned resources the maximum number of lines can be specified
interactively. When using the flag -l the maximum number of per-cpu lines is set to
0, the maximum number of disk lines to 5 and the maximum number of interface lines to
3. These values can be modified again in interactive mode.
k Send a signal to an active process (a.k.a. kill a process).
q Quit the program.
PgDn Show the next page of the process/thread list.
With the arrow-down key the list can be scrolled downwards with single lines.
^F Show the next page of the process/thread list (forward).
With the arrow-down key the list can be scrolled downwards with single lines.
PgUp Show the previous page of the process/thread list.
With the arrow-up key the list can be scrolled upwards with single lines.
^B Show the previous page of the process/thread list (backward).
With the arrow-up key the list can be scrolled upwards with single lines.
^L Redraw the screen.
PCP DATA STORAGE
In order to store system and process level statistics for long-term analysis (e.g. to
check the system load and the active processes running yesterday between 3:00 and 4:00
PM), pcp-atop can store the system and process level statistics in the PCP archive format,
as an archive folio (see mkaf(1)).
All processes/threads are stored in the raw file.
The interval (default: 10 seconds) and number of samples (default: infinite) can be passed
as last arguments. Instead of the number of samples, the flag -S can be used to indicate
that pcp-atop should finish anyhow before midnight.
A PCP archive can be read and visualized again with the flag -r . The argument is a
comma-separated list of names, each of which may be the base name of an archive or the
name of a directory containing one or more archives. If no argument is specified, the
file $PCP_LOG_DIR/pmlogger/HOST/YYYYMMDD is opened for input (where YYYYMMDD are digits
representing the current date, and HOST is the hostname of the machine being logged). If
a filename is specified in the format YYYYMMDD (representing any valid date), the file
$PCP_LOG_DIR/pmlogger/HOST/YYYYMMDD is opened. If a filename with the symbolic name y is
specified, yesterday's daily logfile is opened (this can be repeated so 'yyyy' indicates
the logfile of four days ago).
The samples from the file can be viewed interactively by using the key 't' to show the
next sample, the key 'T' to show the previous sample, the key 'b' to branch to a
particular time or the key 'r' to rewind to the begin of the file.
When output is redirected to a file or pipe, pcp-atop prints all samples in plain ASCII.
The default line length is 80 characters in that case; with the flag -L followed by an
alternate line length, more (or less) columns will be shown.
With the flag -b (begin time) and/or -e (end time) followed by a time argument of the form
HH:MM, a certain time period within the raw file can be selected.
OUTPUT DESCRIPTION
The first sample shows the system level activity since boot (the elapsed time in the
header shows the time since boot). Note that particular counters could have reached their
maximum value (several times) and started by zero again, so do not rely on these figures.
For every sample pcp-atop first shows the lines related to system level activity. If a
particular system resource has not been used during the interval, the entire line related
to this resource is suppressed. So the number of system level lines may vary for each
sample.
After that a list is shown of processes which have been active during the last interval.
This list is by default sorted on cpu consumption, but this order can be changed by the
keys which are previously described.
If values have to be shown by pcp-atop which do not fit in the column width, another
format is used. If e.g. a cpu-consumption of 233216 milliseconds should be shown in a
column width of 4 positions, it is shown as `233s' (in seconds). For large memory
figures, another unit is chosen if the value does not fit (Mb instead of Kb, Gb instead of
Mb, Tb instead of Gb, ...). For other values, a kind of exponent notation is used (value
123456789 shown in a column of 5 positions gives 123e6).
OUTPUT DESCRIPTION - SYSTEM LEVEL
The system level information consists of the following output lines:
PRC Process and thread level totals.
This line contains the total cpu time consumed in system mode (`sys') and in user
mode (`user'), the total number of processes present at this moment (`#proc'), the
total number of threads present at this moment in state `running' (`#trun'),
`sleeping interruptible' (`#tslpi') and `sleeping uninterruptible' (`#tslpu'), the
number of zombie processes (`#zombie'), the number of clone system calls (`clones'),
and the number of processes that ended during the interval (`#exit') when process
accounting is used. Instead of `#exit` the last column may indicate that process
accounting could not be activated (`no procacct`).
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
CPU CPU utilization.
At least one line is shown for the total occupation of all CPUs together.
In case of a multi-processor system, an additional line is shown for every individual
processor (with `cpu' in lower case), sorted on activity. Inactive CPUs will not be
shown by default. The lines showing the per-cpu occupation contain the cpu number in
the last field.
Every line contains the percentage of cpu time spent in kernel mode by all active
processes (`sys'), the percentage of cpu time consumed in user mode (`user') for all
active processes (including processes running with a nice value larger than zero),
the percentage of cpu time spent for interrupt handling (`irq') including softirq,
the percentage of unused cpu time while no processes were waiting for disk-I/O
(`idle'), and the percentage of unused cpu time while at least one process was
waiting for disk-I/O (`wait').
In case of per-cpu occupation, the last column shows the cpu number and the wait
percentage (`w') for that cpu. The number of lines showing the per-cpu occupation
can be limited.
For virtual machines the steal-percentage is shown (`steal'), reflecting the
percentage of cpu time stolen by other virtual machines running on the same hardware.
For physical machines hosting one or more virtual machines, the guest-percentage is
shown (`guest'), reflecting the percentage of cpu time used by the virtual machines.
Notice that this percentage overlaps the user-percentage.
In case of frequency-scaling, all previously mentioned CPU-percentages are relative
to the used scaling of the CPU during the interval. If a CPU has been active for
e.g. 50% in user mode during the interval while the frequency-scaling of that CPU was
40%, only 20% of the full capacity of the CPU has been used in user mode.
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
CPL CPU load information.
This line contains the load average figures reflecting the number of threads that are
available to run on a CPU (i.e. part of the runqueue) or that are waiting for disk
I/O. These figures are averaged over 1 (`avg1'), 5 (`avg5') and 15 (`avg15') minutes.
Furthermore the number of context switches (`csw'), the number of serviced interrupts
(`intr') and the number of available CPUs are shown.
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
MEM Memory occupation.
This line contains the total amount of physical memory (`tot'), the amount of memory
which is currently free (`free'), the amount of memory in use as page cache including
the total resident shared memory (`cache'), the amount of memory within the page
cache that has to be flushed to disk (`dirty'), the amount of memory used for
filesystem meta data (`buff'), the amount of memory being used for kernel mallocs
(`slab'), the amount of slab memory that is reclaimable (`slrec'), the resident size
of shared memory including tmpfs (`shmem`), the resident size of shared memory
(`shrss`) the amount of shared memory that is currently swapped (`shswp`), the amount
of memory that is currently claimed by vmware's balloon driver (`vmbal`), the amount
of memory that is claimed for huge pages (`hptot`), and the amount of huge page
memory that is really in use (`hpuse`).
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
SWP Swap occupation and overcommit info.
This line contains the total amount of swap space on disk (`tot') and the amount of
free swap space (`free').
Furthermore the committed virtual memory space (`vmcom') and the maximum limit of the
committed space (`vmlim', which is by default swap size plus 50% of memory size) is
shown. The committed space is the reserved virtual space for all allocations of
private memory space for processes. The kernel only verifies whether the committed
space exceeds the limit if strict overcommit handling is configured
(vm.overcommit_memory is 2).
PAG Paging frequency.
This line contains the number of scanned pages (`scan') due to the fact that free
memory drops below a particular threshold and the number times that the kernel tries
to reclaim pages due to an urgent need (`stall').
Also the number of memory pages the system read from swap space (`swin') and the
number of memory pages the system wrote to swap space (`swout') are shown.
LVM/MDD/DSK
Logical volume/multiple device/disk utilization.
Per active unit one line is produced, sorted on unit activity. Such line shows the
name (e.g. VolGroup00-lvtmp for a logical volume or sda for a hard disk), the busy
percentage i.e. the portion of time that the unit was busy handling requests
(`busy'), the number of read requests issued (`read'), the number of write requests
issued (`write'), the number of KiBytes per read (`KiB/r'), the number of KiBytes per
write (`KiB/w'), the number of MiBytes per second throughput for reads (`MBr/s'), the
number of MiBytes per second throughput for writes (`MBw/s'), the average queue depth
(`avq') and the average number of milliseconds needed by a request (`avio') for seek,
latency and data transfer.
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
The number of lines showing the units can be limited per class (LVM, MDD or DSK) with
the 'l' key or statically (see separate man-page of pcp-atoprc(5)). By specifying
the value 0 for a particular class, no lines will be shown any more for that class.
NFM Network Filesystem (NFS) mount at the client side.
For each NFS-mounted filesystem, a line is shown that contains the mounted server
directory, the name of the server (`srv'), the total number of bytes physically read
from the server (`read') and the total number of bytes physically written to the
server (`write'). Data transfer is subdivided in the number of bytes read via normal
read() system calls (`nread'), the number of bytes written via normal read() system
calls (`nwrit'), the number of bytes read via direct I/O (`dread'), the number of
bytes written via direct I/O (`dwrit'), the number of bytes read via memory mapped
I/O pages (`mread'), and the number of bytes written via memory mapped I/O pages
(`mwrit').
NFC Network Filesystem (NFS) client side counters.
This line contains the number of RPC calls issues by local processes (`rpc'), the
number of read RPC calls (`read`) and write RPC calls (`rpwrite') issued to the NFS
server, the number of RPC calls being retransmitted (`retxmit') and the number of
authorization refreshes (`autref').
NFS Network Filesystem (NFS) server side counters.
This line contains the number of RPC calls received from NFS clients (`rpc'), the
number of read RPC calls received (`cread`), the number of write RPC calls received
(`cwrit'), the number of network requests handled via TCP (`nettcp'), the number of
network requests handled via UDP (`netudp'), the number of Megabytes/second returned
to read requests by clients (`MBcr/s`), the number of Megabytes/second passed in
write requests by clients (`MBcw/s`), the number of reply cache hits (`rchits'), the
number of reply cache misses (`rcmiss') and the number of uncached requests
(`rcnoca'). Furthermore some error counters indicating the number of requests with a
bad format (`badfmt') or a bad authorization (`badaut'), and a counter indicating the
number of bad clients (`badcln'). and the number of authorization refreshes
(`autref').
NET Network utilization (TCP/IP).
One line is shown for activity of the transport layer (TCP and UDP), one line for the
IP layer and one line per active interface.
For the transport layer, counters are shown concerning the number of received TCP
segments including those received in error (`tcpi'), the number of transmitted TCP
segments excluding those containing only retransmitted octets (`tcpo'), the number of
UDP datagrams received (`udpi'), the number of UDP datagrams transmitted (`udpo'),
the number of active TCP opens (`tcpao'), the number of passive TCP opens (`tcppo'),
the number of TCP output retransmissions (`tcprs'), the number of TCP input errors
(`tcpie'), the number of TCP output resets (`tcpor'), the number of UDP no ports
(`udpnp'), and the number of UDP input errors (`udpie').
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
These counters are related to IPv4 and IPv6 combined.
For the IP layer, counters are shown concerning the number of IP datagrams received
from interfaces, including those received in error (`ipi'), the number of IP
datagrams that local higher-layer protocols offered for transmission (`ipo'), the
number of received IP datagrams which were forwarded to other interfaces (`ipfrw'),
the number of IP datagrams which were delivered to local higher-layer protocols
(`deliv'), the number of received ICMP datagrams (`icmpi'), and the number of
transmitted ICMP datagrams (`icmpo').
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
These counters are related to IPv4 and IPv6 combined.
For every active network interface one line is shown, sorted on the interface
activity. Such line shows the name of the interface and its busy percentage in the
first column. The busy percentage for half duplex is determined by comparing the
interface speed with the number of bits transmitted and received per second; for full
duplex the interface speed is compared with the highest of either the transmitted or
the received bits. When the interface speed can not be determined (e.g. for the
loopback interface), `---' is shown instead of the percentage.
Furthermore the number of received packets (`pcki'), the number of transmitted
packets (`pcko'), the line speed of the interface (`sp'), the effective amount of
bits received per second (`si'), the effective amount of bits transmitted per second
(`so'), the number of collisions (`coll'), the number of received multicast packets
(`mlti'), the number of errors while receiving a packet (`erri'), the number of
errors while transmitting a packet (`erro'), the number of received packets dropped
(`drpi'), and the number of transmitted packets dropped (`drpo').
If the screen-width does not allow all of these counters, only a relevant subset is
shown.
The number of lines showing the network interfaces can be limited.
OUTPUT DESCRIPTION - PROCESS LEVEL
Following the system level information, the processes are shown from which the resource
utilization has changed during the last interval. These processes might have used cpu time
or issued disk or network requests. However a process is also shown if part of it has been
paged out due to lack of memory (while the process itself was in sleep state).
Per process the following fields may be shown (in alphabetical order), depending on the
current output mode as described in the section INTERACTIVE COMMANDS and depending on the
current width of your window:
AVGRSZ The average size of one read-action on disk.
AVGWSZ The average size of one write-action on disk.
CID Container ID (Docker) of 12 hexadecimal digits, referring to the container in
which the process/thread is running. If a process has been started and finished
during the last interval, a `?' is shown because the container ID is not part of
the standard process accounting record.
CMD The name of the process. This name can be surrounded by "less/greater than"
signs (`<name>') which means that the process has finished during the last
interval.
Behind the abbreviation `CMD' in the header line, the current page number and the
total number of pages of the process/thread list are shown.
COMMAND-LINE
The full command line of the process (including arguments). If the length of the
command line exceeds the length of the screen line, the arrow keys -> and <- can
be used for horizontal scroll.
Behind the verb `COMMAND-LINE' in the header line, the current page number and
the total number of pages of the process/thread list are shown.
CPU The occupation percentage of this process related to the available capacity for
this resource on system level.
CPUNR The identification of the CPU the (main) thread is running on or has recently
been running on.
CTID Container ID (OpenVZ). If a process has been started and finished during the
last interval, a `?' is shown because the container ID is not part of the
standard process accounting record.
DSK The occupation percentage of this process related to the total load that is
produced by all processes (i.e. total disk accesses by all processes during the
last interval).
This information is shown when per process "storage accounting" is active in the
kernel.
EGID Effective group-id under which this process executes.
ENDATE Date that the process has been finished. If the process is still running, this
field shows `active'.
ENTIME Time that the process has been finished. If the process is still running, this
field shows `active'.
ENVID Virtual environment identified (OpenVZ only).
EUID Effective user-id under which this process executes.
EXC The exit code of a terminated process (second position of column `ST' is E) or
the fatal signal number (second position of column `ST' is S or C).
FSGID Filesystem group-id under which this process executes.
FSUID Filesystem user-id under which this process executes.
MAJFLT The number of page faults issued by this process that have been solved by
creating/loading the requested memory page.
MEM The occupation percentage of this process related to the available capacity for
this resource on system level.
MINFLT The number of page faults issued by this process that have been solved by
reclaiming the requested memory page from the free list of pages.
NET The occupation percentage of this process related to the total load that is
produced by all processes (i.e. consumed network bandwidth of all processes
during the last interval).
This information will only be shown when kernel module `netatop' is loaded.
NICE The more or less static priority that can be given to a process on a scale from
-20 (high priority) to +19 (low priority).
NPROCS The number of active and terminated processes accumulated for this user or
program.
PID Process-id.
POLI The policies 'norm' (normal, which is SCHED_OTHER), 'btch' (batch) and 'idle'
refer to timesharing processes. The policies 'fifo' (SCHED_FIFO) and 'rr' (round
robin, which is SCHED_RR) refer to realtime processes.
PPID Parent process-id.
PRI The process' priority ranges from 0 (highest priority) to 139 (lowest priority).
Priority 0 to 99 are used for realtime processes (fixed priority independent of
their behavior) and priority 100 to 139 for timesharing processes (variable
priority depending on their recent CPU consumption and the nice value).
PSIZE The proportional memory size of this process (or user).
Every process shares resident memory with other processes. E.g. when a particular
program is started several times, the code pages (text) are only loaded once in
memory and shared by all incarnations. Also the code of shared libraries is
shared by all processes using that shared library, as well as shared memory and
memory-mapped files. For the PSIZE calculation of a process, the resident memory
of a process that is shared with other processes is divided by the number of
sharers. This means, that every process is accounted for a proportional part of
that memory. Accumulating the PSIZE values of all processes in the system gives a
reliable impression of the total resident memory consumed by all processes.
Since gathering of all values that are needed to calculate the PSIZE is a
relatively time-consuming task, the 'R' key (or '-R' flag) should be active.
Gathering these values also requires superuser privileges (otherwise '?K' is
shown in the output).
RDDSK When the kernel maintains standard io statistics (>= 2.6.20):
The read data transfer issued physically on disk (so reading from the disk cache
is not accounted for).
Unfortunately, the kernel aggregates the data tranfer of a process to the data
transfer of its parent process when terminating, so you might see transfers for
(parent) processes like cron, bash or init, that are not really issued by them.
RGID The real group-id under which the process executes.
RGROW The amount of resident memory that the process has grown during the last
interval. A resident growth can be caused by touching memory pages which were not
physically created/loaded before (load-on-demand). Note that a resident growth
can also be negative e.g. when part of the process is paged out due to lack of
memory or when the process frees dynamically allocated memory. For a process
which started during the last interval, the resident growth reflects the total
resident size of the process at that moment.
RSIZE The total resident memory usage consumed by this process (or user). Notice that
the RSIZE of a process includes all resident memory used by that process, even if
certain memory parts are shared with other processes (see also the explanation of
PSIZE).
RTPR Realtime priority according the POSIX standard. Value can be 0 for a timesharing
process (policy 'norm', 'btch' or 'idle') or ranges from 1 (lowest) till 99
(highest) for a realtime process (policy 'rr' or 'fifo').
RUID The real user-id under which the process executes.
S The current state of the (main) thread: `R' for running (currently processing or
in the runqueue), `S' for sleeping interruptible (wait for an event to occur),
`D' for sleeping non-interruptible, `Z' for zombie (waiting to be synchronized
with its parent process), `T' for stopped (suspended or traced), `W' for
swapping, and `E' (exit) for processes which have finished during the last
interval.
SGID The saved group-id of the process.
ST The status of a process.
The first position indicates if the process has been started during the last
interval (the value N means 'new process').
The second position indicates if the process has been finished during the last
interval.
The value E means 'exit' on the process' own initiative; the exit code is
displayed in the column `EXC'.
The value S means that the process has been terminated unvoluntarily by a signal;
the signal number is displayed in the in the column `EXC'.
The value C means that the process has been terminated unvoluntarily by a signal,
producing a core dump in its current directory; the signal number is displayed in
the column `EXC'.
STDATE The start date of the process.
STTIME The start time of the process.
SUID The saved user-id of the process.
SWAPSZ The swap space consumed by this process (or user).
SYSCPU CPU time consumption of this process in system mode (kernel mode), usually due to
system call handling.
THR Total number of threads within this process. All related threads are contained
in a thread group, represented by pcp-atop as one line or as a separate line when
the 'y' key (or -y flag) is active.
On Linux 2.4 systems it is hardly possible to determine which threads (i.e.
processes) are related to the same thread group. Every thread is represented by
pcp-atop as a separate line.
TID Thread-id. All threads within a process run with the same PID but with a
different TID. This value is shown for individual threads in multi-threaded
processes (when using the key 'y').
TRUN Number of threads within this process that are in the state 'running' (R).
TSLPI Number of threads within this process that are in the state 'interruptible
sleeping' (S).
TSLPU Number of threads within this process that are in the state 'uninterruptible
sleeping' (D).
USRCPU CPU time consumption of this process in user mode, due to processing the own
program text.
VDATA The virtual memory size of the private data used by this process (including heap
and shared library data).
VGROW The amount of virtual memory that the process has grown during the last interval.
A virtual growth can be caused by e.g. issueing a malloc() or attaching a shared
memory segment. Note that a virtual growth can also be negative by e.g. issueing
a free() or detaching a shared memory segment. For a process which started
during the last interval, the virtual growth reflects the total virtual size of
the process at that moment.
VPID Virtual process-id (within an OpenVZ container). If a process has been started
and finished during the last interval, a `?' is shown because the virtual
process-id is not part of the standard process accounting record.
VSIZE The total virtual memory usage consumed by this process (or user).
VSLIBS The virtual memory size of the (shared) text of all shared libraries used by this
process.
VSTACK The virtual memory size of the (private) stack used by this process
VSTEXT The virtual memory size of the (shared) text of the executable program.
WRDSK When the kernel maintains standard io statistics (>= 2.6.20):
The write data transfer issued physically on disk (so writing to the disk cache
is not accounted for). This counter is maintained for the application process
that writes its data to the cache (assuming that this data is physically
transferred to disk later on). Notice that disk I/O needed for swapping is not
taken into account.
Unfortunately, the kernel aggregates the data tranfer of a process to the data
transfer of its parent process when terminating, so you might see transfers for
(parent) processes like cron, bash or init, that are not really issued by them.
WCANCL When the kernel maintains standard io statistics (>= 2.6.20):
The write data transfer previously accounted for this process or another process
that has been cancelled. Suppose that a process writes new data to a file and
that data is removed again before the cache buffers have been flushed to disk.
Then the original process shows the written data as WRDSK, while the process that
removes/truncates the file shows the unflushed removed data as WCANCL.
PARSEABLE OUTPUT
With the flag -P followed by a list of one or more labels (comma-separated), parseable
output is produced for each sample. The labels that can be specified for system-level
statistics correspond to the labels (first verb of each line) that can be found in the
interactive output: "CPU", "cpu" "CPL" "MEM", "SWP", "PAG", "LVM", "MDD", "DSK", "NFM",
"NFC", "NFS" and "NET".
For process-level statistics special labels are introduced: "PRG" (general), "PRC" (cpu),
"PRM" (memory), "PRD" (disk, only if "storage accounting" is active) and "PRN" (network,
only if the kernel module 'netatop' has been installed).
With the label "ALL", all system and process level statistics are shown.
For every interval all requested lines are shown whereafter pcp-atop shows a line just
containing the label "SEP" as a separator before the lines for the next sample are
generated.
When a sample contains the values since boot, pcp-atop shows a line just containing the
label "RESET" before the lines for this sample are generated.
The first part of each output-line consists of the following six fields: label (the name
of the label), host (the name of this machine), epoch (the time of this interval as number
of seconds since 1-1-1970), date (date of this interval in format YYYY/MM/DD), time (time
of this interval in format HH:MM:SS), and interval (number of seconds elapsed for this
interval).
The subsequent fields of each output-line depend on the label:
CPU Subsequent fields: total number of clock-ticks per second for this machine,
number of processors, consumption for all CPUs in system mode (clock-ticks),
consumption for all CPUs in user mode (clock-ticks), consumption for all CPUs in
user mode for niced processes (clock-ticks), consumption for all CPUs in idle
mode (clock-ticks), consumption for all CPUs in wait mode (clock-ticks),
consumption for all CPUs in irq mode (clock-ticks), consumption for all CPUs in
softirq mode (clock-ticks), consumption for all CPUs in steal mode (clock-ticks),
consumption for all CPUs in guest mode (clock-ticks) overlapping user mode,
frequency of all CPUs and frequency percentage of all CPUs.
cpu Subsequent fields: total number of clock-ticks per second for this machine,
processor-number, consumption for this CPU in system mode (clock-ticks),
consumption for this CPU in user mode (clock-ticks), consumption for this CPU in
user mode for niced processes (clock-ticks), consumption for this CPU in idle
mode (clock-ticks), consumption for this CPU in wait mode (clock-ticks),
consumption for this CPU in irq mode (clock-ticks), consumption for this CPU in
softirq mode (clock-ticks), consumption for this CPU in steal mode (clock-ticks),
consumption for this CPU in guest mode (clock-ticks) overlapping user mode,
frequency of this CPU and frequency percentage of this CPU.
CPL Subsequent fields: number of processors, load average for last minute, load
average for last five minutes, load average for last fifteen minutes, number of
context-switches, and number of device interrupts.
MEM Subsequent fields: page size for this machine (in bytes), size of physical memory
(pages), size of free memory (pages), size of page cache (pages), size of buffer
cache (pages), size of slab (pages), dirty pages in cache (pages), reclaimable
part of slab (pages), total size of vmware's balloon pages (pages), total size of
shared memory (pages), size of resident shared memory (pages), size of swapped
shared memory (pages), huge page size (in bytes), total size of huge pages (huge
pages), and size of free huge pages (huge pages).
SWP Subsequent fields: page size for this machine (in bytes), size of swap (pages),
size of free swap (pages), 0 (future use), size of committed space (pages), and
limit for committed space (pages).
PAG Subsequent fields: page size for this machine (in bytes), number of page scans,
number of allocstalls, 0 (future use), number of swapins, and number of swapouts.
LVM/MDD/DSK
For every logical volume/multiple device/hard disk one line is shown.
Subsequent fields: name, number of milliseconds spent for I/O, number of reads
issued, number of sectors transferred for reads, number of writes issued, and
number of sectors transferred for write.
NFM Subsequent fields: mounted NFS filesystem, total number of bytes read, total
number of bytes written, number of bytes read by normal system calls, number of
bytes written by normal system calls, number of bytes read by direct I/O, number
of bytes written by direct I/O, number of pages read by memory-mapped I/O, and
number of pages written by memory-mapped I/O.
NFC Subsequent fields: number of transmitted RPCs, number of transmitted read RPCs,
number of transmitted write RPCs, number of RPC retransmissions, and number of
authorization refreshes.
NFS Subsequent fields: number of handled RPCs, number of received read RPCs, number
of received write RPCs, number of bytes read by clients, number of bytes written
by clients, number of RPCs with bad format, number of RPCs with bad
authorization, number of RPCs from bad client, total number of handled network
requests, number of handled network requests via TCP, number of handled network
requests via UDP, number of handled TCP connections, number of hits on reply
cache, number of misses on reply cache, and number of uncached requests.
NET First one line is produced for the upper layers of the TCP/IP stack.
Subsequent fields: the verb "upper", number of packets received by TCP, number of
packets transmitted by TCP, number of packets received by UDP, number of packets
transmitted by UDP, number of packets received by IP, number of packets
transmitted by IP, number of packets delivered to higher layers by IP, and number
of packets forwarded by IP.
Next one line is shown for every interface.
Subsequent fields: name of the interface, number of packets received by the
interface, number of bytes received by the interface, number of packets
transmitted by the interface, number of bytes transmitted by the interface,
interface speed, and duplex mode (0=half, 1=full).
PRG For every process one line is shown.
Subsequent fields: PID (unique ID of task), name (between brackets), state, real
uid, real gid, TGID (group number of related tasks/threads), total number of
threads, exit code, start time (epoch), full command line (between brackets),
PPID, number of threads in state 'running' (R), number of threads in state
'interruptible sleeping' (S), number of threads in state 'uninterruptible
sleeping' (D), effective uid, effective gid, saved uid, saved gid, filesystem
uid, filesystem gid, elapsed time (hertz), is_process (y/n), OpenVZ virtual pid
(VPID), OpenVZ container id (CTID) and Docker container id (CID).
PRC For every process one line is shown.
Subsequent fields: PID, name (between brackets), state, total number of clock-
ticks per second for this machine, CPU-consumption in user mode (clockticks),
CPU-consumption in system mode (clockticks), nice value, priority, realtime
priority, scheduling policy, current CPU, sleep average, TGID (group number of
related tasks/threads) and is_process (y/n).
PRM For every process one line is shown.
Subsequent fields: PID, name (between brackets), state, page size for this
machine (in bytes), virtual memory size (Kbytes), resident memory size (Kbytes),
shared text memory size (Kbytes), virtual memory growth (Kbytes), resident memory
growth (Kbytes), number of minor page faults, number of major page faults,
virtual library exec size (Kbytes), virtual data size (Kbytes), virtual stack
size (Kbytes), swap space used (Kbytes), TGID (group number of related
tasks/threads), is_process (y/n) and proportional set size (Kbytes) if in 'R'
option is specified.
PRD For every process one line is shown.
Subsequent fields: PID, name (between brackets), state, obsoleted kernel patch
installed ('n'), standard io statistics used ('y' or 'n'), number of reads on
disk, cumulative number of sectors read, number of writes on disk, cumulative
number of sectors written, cancelled number of written sectors, TGID (group
number of related tasks/threads) and is_process (y/n).
If the standard I/O statistics (>= 2.6.20) are not used, the disk I/O counters
per process are not relevant. The counters 'number of reads on disk' and 'number
of writes on disk' are obsoleted anyhow.
PRN For every process one line is shown.
Subsequent fields: PID, name (between brackets), state, kernel module 'netatop'
loaded ('y' or 'n'), number of TCP-packets transmitted, cumulative size of TCP-
packets transmitted, number of TCP-packets received, cumulative size of TCP-
packets received, number of UDP-packets transmitted, cumulative size of UDP-
packets transmitted, number of UDP-packets received, cumulative size of UDP-
packets transmitted, number of raw packets transmitted (obsolete, always 0),
number of raw packets received (obsolete, always 0), TGID (group number of
related tasks/threads) and is_process (y/n).
EXAMPLES
To monitor the current system load interactively with an interval of 5 seconds:
pcp atop 5
To monitor the system load and write it to a file (in plain ASCII) with an interval of one
minute during half an hour with active processes sorted on memory consumption:
pcp atop -M 60 30 > /log/pcp-atop.mem
Store information about the system and process activity in a PCP archive folio with an
interval of ten minutes during an hour:
pcp atop -w /tmp/pcp-atop 600 6
View the contents of this file interactively:
pcp atop -r /tmp/pcp-atop
View the processor and disk utilization of this file in parseable format:
pcp atop -PCPU,DSK -r /tmp/pcp-atop.raw
View the contents of today's standard logfile interactively:
pcp atop -r
View the contents of the standard logfile of the day before yesterday interactively:
pcp atop -r yy
View the contents of the standard logfile of 2014, June 7 from 02:00 PM onwards
interactively:
pcp atop -r 20140607 -b 14:00
FILES
/etc/atoprc
Configuration file containing system-wide default values. See related man-page.
~/.atoprc
Configuration file containing personal default values. See related man-page.
NOTES
pcp-atop is based on the source code of the atop(1) command from http://atoptool.nl and
aims to be command line and output compatible with it as much as possible. Some features
of that atop command are not available in pcp-atop.
Some features of pcp-atop (such as reporting on the Apache HTTP daemon, and NFS client
mounts) are only activated if the corresonding PCP metrics are available. Refer to the
documentation for pmdaapache(1) and pmdanfsclient(1) for further details on activating
these metrics.
SEE ALSO
pcp(1), pcp-atopsar(1), pmdaapache(1), pmdanfsclient(1), pmdaproc(1), mkaf(1),
pmlogger(1), pmlogger_daily(1), PCPIntro(1) and pcp-atoprc(5).