Provided by: manpages-posix-dev_2013a-2_all 
PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface
may differ (consult the corresponding Linux manual page for details of Linux behavior), or the interface
may not be implemented on Linux.
NAME
pclose — close a pipe stream to or from a process
SYNOPSIS
#include <stdio.h> int pclose(FILE *stream);
DESCRIPTION
The pclose() function shall close a stream that was opened by popen(), wait for the command to terminate,
and return the termination status of the process that was running the command language interpreter.
However, if a call caused the termination status to be unavailable to pclose(), then pclose() shall
return −1 with errno set to [ECHILD] to report this situation. This can happen if the application calls
one of the following functions:
* wait()
* waitpid() with a pid argument less than or equal to 0 or equal to the process ID of the command line
interpreter
* Any other function not defined in this volume of POSIX.1‐2008 that could do one of the above
In any case, pclose() shall not return before the child process created by popen() has terminated.
If the command language interpreter cannot be executed, the child termination status returned by pclose()
shall be as if the command language interpreter terminated using exit(127) or _exit(127).
The pclose() function shall not affect the termination status of any child of the calling process other
than the one created by popen() for the associated stream.
If the argument stream to pclose() is not a pointer to a stream created by popen(), the result of
pclose() is undefined.
RETURN VALUE
Upon successful return, pclose() shall return the termination status of the command language interpreter.
Otherwise, pclose() shall return −1 and set errno to indicate the error.
ERRORS
The pclose() function shall fail if:
ECHILD The status of the child process could not be obtained, as described above.
The following sections are informative.
EXAMPLES
None.
APPLICATION USAGE
None.
RATIONALE
There is a requirement that pclose() not return before the child process terminates. This is intended to
disallow implementations that return [EINTR] if a signal is received while waiting. If pclose() returned
before the child terminated, there would be no way for the application to discover which child used to be
associated with the stream, and it could not do the cleanup itself.
If the stream pointed to by stream was not created by popen(), historical implementations of pclose()
return −1 without setting errno. To avoid requiring pclose() to set errno in this case, POSIX.1‐2008
makes the behavior unspecified. An application should not use pclose() to close any stream that was not
created by popen().
Some historical implementations of pclose() either block or ignore the signals SIGINT, SIGQUIT, and
SIGHUP while waiting for the child process to terminate. Since this behavior is not described for the
pclose() function in POSIX.1‐2008, such implementations are not conforming. Also, some historical
implementations return [EINTR] if a signal is received, even though the child process has not terminated.
Such implementations are also considered non-conforming.
Consider, for example, an application that uses:
popen("command", "r")
to start command, which is part of the same application. The parent writes a prompt to its standard
output (presumably the terminal) and then reads from the popen()ed stream. The child reads the response
from the user, does some transformation on the response (pathname expansion, perhaps) and writes the
result to its standard output. The parent process reads the result from the pipe, does something with it,
and prints another prompt. The cycle repeats. Assuming that both processes do appropriate buffer
flushing, this would be expected to work.
To conform to POSIX.1‐2008, pclose() must use waitpid(), or some similar function, instead of wait().
The code sample below illustrates how the pclose() function might be implemented on a system conforming
to POSIX.1‐2008.
int pclose(FILE *stream)
{
int stat;
pid_t pid;
pid = <pid for process created for stream by popen()>
(void) fclose(stream);
while (waitpid(pid, &stat, 0) == -1) {
if (errno != EINTR){
stat = -1;
break;
}
}
return(stat);
}
FUTURE DIRECTIONS
None.
SEE ALSO
fork(), popen(), wait()
The Base Definitions volume of POSIX.1‐2008, <stdio.h>
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2013 Edition,
Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base
Specifications Issue 7, Copyright (C) 2013 by the Institute of Electrical and Electronics Engineers, Inc
and The Open Group. (This is POSIX.1-2008 with the 2013 Technical Corrigendum 1 applied.) In the event
of any discrepancy between this version and the original IEEE and The Open Group Standard, the original
IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at
http://www.unix.org/online.html .
Any typographical or formatting errors that appear in this page are most likely to have been introduced
during the conversion of the source files to man page format. To report such errors, see
https://www.kernel.org/doc/man-pages/reporting_bugs.html .