Provided by: freebsd-manpages_11.1-3_all 
NAME
cxgbev — Chelsio T4-, T5-, and T6-based 100Gb, 40Gb, 25Gb, 10Gb, and 1Gb Ethernet VF driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel
configuration file:
device cxgbe
device cxgbev
To load the driver as a module at boot time, place the following line in loader.conf(5):
if_cxgbev_load="YES"
DESCRIPTION
The cxgbev driver provides support for Virtual Functions on PCI Express Ethernet adapters
based on the Chelsio Terminator 4, Terminator 5, and Terminator 6 ASICs (T4, T5, and T6).
The driver supports Jumbo Frames, Transmit/Receive checksum offload, TCP segmentation
offload (TSO), Large Receive Offload (LRO), VLAN tag insertion/extraction, VLAN checksum
offload, VLAN TSO, and Receive Side Steering (RSS). For further hardware information and
questions related to hardware requirements, see http://www.chelsio.com/.
The cxgbev driver uses different names for devices based on the associated ASIC:
ASIC Port Name Parent Device
T4 cxgbev t4vf
T5 cxlv t5vf
T6 ccv t6vf
Loader tunables with the hw.cxgbe prefix apply to VFs from all cards. The Physical Function
driver for Chelsio Terminator adapters shares these tunables. The driver provides sysctl
MIBs for both ports and parent devices using the names above. For example, a T5 VF provides
port MIBs under dev.cxlv and parent device MIBs under dev.t5vf. References to sysctl MIBs
in the remainder of this page use dev.<port> for port MIBs and dev.<nexus> for parent device
MIBs.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The cxgbev driver supports Virtual Functions on 100Gb and 25Gb Ethernet adapters based on
the T6 ASIC:
• Chelsio T6225-CR
• Chelsio T6225-SO-CR
• Chelsio T62100-LP-CR
• Chelsio T62100-SO-CR
• Chelsio T62100-CR
The cxgbev driver supports Virtual Functions on 40Gb, 10Gb and 1Gb Ethernet adapters based
on the T5 ASIC:
• Chelsio T580-CR
• Chelsio T580-LP-CR
• Chelsio T580-LP-SO-CR
• Chelsio T560-CR
• Chelsio T540-CR
• Chelsio T540-LP-CR
• Chelsio T522-CR
• Chelsio T520-LL-CR
• Chelsio T520-CR
• Chelsio T520-SO
• Chelsio T520-BT
• Chelsio T504-BT
The cxgbev driver supports Virtual Functions on 10Gb and 1Gb Ethernet adapters based on the
T4 ASIC:
• Chelsio T420-CR
• Chelsio T422-CR
• Chelsio T440-CR
• Chelsio T420-BCH
• Chelsio T440-BCH
• Chelsio T440-CH
• Chelsio T420-SO
• Chelsio T420-CX
• Chelsio T420-BT
• Chelsio T404-BT
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in
loader.conf(5).
hw.cxgbe.ntxq10g
Number of tx queues used for a 10Gb or higher-speed port. The default is 16 or the
number of CPU cores in the system, whichever is less.
hw.cxgbe.nrxq10g
Number of rx queues used for a 10Gb or higher-speed port. The default is 8 or the
number of CPU cores in the system, whichever is less.
hw.cxgbe.ntxq1g
Number of tx queues used for a 1Gb port. The default is 4 or the number of CPU
cores in the system, whichever is less.
hw.cxgbe.nrxq1g
Number of rx queues used for a 1Gb port. The default is 2 or the number of CPU
cores in the system, whichever is less.
hw.cxgbe.holdoff_timer_idx_10G
hw.cxgbe.holdoff_timer_idx_1G
Timer index value used to delay interrupts. The holdoff timer list has the values
1, 5, 10, 50, 100, and 200 by default (all values are in microseconds) and the index
selects a value from this list. The default value is 1 which means the timer value
is 5us. Different interfaces can be assigned different values at any time via the
dev.<port>.X.holdoff_tmr_idx sysctl.
hw.cxgbe.holdoff_pktc_idx_10G
hw.cxgbe.holdoff_pktc_idx_1G
Packet-count index value used to delay interrupts. The packet-count list has the
values 1, 8, 16, and 32 by default, and the index selects a value from this list.
The default value is -1 which means packet counting is disabled and interrupts are
generated based solely on the holdoff timer value. Different interfaces can be
assigned different values via the dev.<port>.X.holdoff_pktc_idx sysctl. This sysctl
works only when the interface has never been marked up (as done by ifconfig up).
hw.cxgbe.qsize_txq
Number of entries in a transmit queue's descriptor ring. A buf_ring of the same
size is also allocated for additional software queuing. See ifnet(9). The default
value is 1024. Different interfaces can be assigned different values via the
dev.<port>.X.qsize_txq sysctl. This sysctl works only when the interface has never
been marked up (as done by ifconfig up).
hw.cxgbe.qsize_rxq
Number of entries in a receive queue's descriptor ring. The default value is 1024.
Different interfaces can be assigned different values via the dev.<port>.X.qsize_rxq
sysctl. This sysctl works only when the interface has never been marked up (as done
by ifconfig up).
hw.cxgbe.interrupt_types
Permitted interrupt types. Bit 0 represents INTx (line interrupts), bit 1 MSI, and
bit 2 MSI-X. The default is 7 (all allowed). The driver selects the best possible
type out of the allowed types. Note that Virtual Functions do not support INTx
interrupts and fail to attach if neither MSI nor MSI-X are enabled.
hw.cxgbe.fl_pktshift
Number of padding bytes inserted before the beginning of an Ethernet frame in the
receive buffer. The default value of 2 ensures that the Ethernet payload (usually
the IP header) is at a 4 byte aligned address. 0-7 are all valid values.
hw.cxgbe.fl_pad
A non-zero value ensures that writes from the hardware to a receive buffer are
padded up to the specified boundary. The default is -1 which lets the driver pick a
pad boundary. 0 disables trailer padding completely.
hw.cxgbe.buffer_packing
Allow the hardware to deliver multiple frames in the same receive buffer
opportunistically. The default is -1 which lets the driver decide. 0 or 1
explicitly disable or enable this feature.
hw.cxgbe.allow_mbufs_in_cluster
1 allows the driver to lay down one or more mbufs within the receive buffer
opportunistically. This is the default. 0 prohibits the driver from doing so.
hw.cxgbe.largest_rx_cluster
hw.cxgbe.safest_rx_cluster
Sizes of rx clusters. Each of these must be set to one of the sizes available
(usually 2048, 4096, 9216, and 16384) and largest_rx_cluster must be greater than or
equal to safest_rx_cluster. The defaults are 16384 and 4096 respectively. The
driver never attempts to allocate a receive buffer larger than largest_rx_cluster
and falls back to allocating buffers of safest_rx_cluster size if an allocation
larger than safest_rx_cluster fails. Note that largest_rx_cluster merely
establishes a ceiling -- the driver is allowed to allocate buffers of smaller sizes.
Certain settings and resources for Virtual Functions are dictated by the parent Physical
Function driver. For example, the Physical Function driver limits the number of queues
available to a Virtual Function. Some of these limits can be adjusted in the firmware
configuration file used with the Physical Function driver.
The PAUSE settings on the port of a Virtual Function are inherited from the settings of the
same port on the Physical Function. Virtual Functions cannot modify the setting and track
changes made to the associated port's setting by the Physical Function driver.
Receive queues on a Virtual Function always drop packets in response to congestion
(equivalent to setting hw.cxgbe.cong_drop to 1).
The VF driver currently depends on the PF driver. As a result, loading the VF driver also
loads the PF driver as a dependency.
SUPPORT
For general information and support, go to the Chelsio support website at:
http://www.chelsio.com/.
If an issue is identified with this driver with a supported adapter, email all the specific
information related to the issue to ⟨support@chelsio.com⟩.
SEE ALSO
altq(4), arp(4), cxgbe(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The cxgbev device driver first appeared in FreeBSD 11.1 and FreeBSD 11.1.
AUTHORS
The cxgbev driver was written by Navdeep Parhar <np@FreeBSD.org> and John Baldwin
<jhb@FreeBSD.org>.