Ubuntu Manpage: dc — DEC/Intel 21143 and clone 10/100 Ethernet driver

Provided by: freebsd-manpages_11.1-3_all

NAME

     dc — DEC/Intel 21143 and clone 10/100 Ethernet driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel
     configuration file:

           device miibus
           device dc

     Alternatively, to load the driver as a module at boot time, place the following line in
     loader.conf(5):

           if_dc_load="YES"

DESCRIPTION

The dc driver provides support for several PCI Fast Ethernet adapters and embedded
controllers based on the DEC/Intel 21143 chipset and clones.

All of supported chipsets have the same general register layout, DMA descriptor format and
method of operation. All of the clone chips are based on the 21143 design with various
modifications. The 21143 itself has support for 10baseT, BNC, AUI, MII and symbol media
attachments, 10 and 100Mbps speeds in full or half duplex, built in NWAY autonegotiation and
wake on LAN. The 21143 also offers several receive filter programming options including
perfect filtering, inverse perfect filtering and hash table filtering.

Some clone chips duplicate the 21143 fairly closely while others only maintain superficial
similarities. Some support only MII media attachments. Others use different receiver
filter programming mechanisms. At least one supports only chained DMA descriptors (most
support both chained descriptors and contiguously allocated fixed size rings). Some chips
(especially the PNIC) also have peculiar bugs. The dc driver does its best to provide
generalized support for all of these chipsets in order to keep special case code to a
minimum.

These chips are used by many vendors which makes it difficult to provide a complete list of
all supported cards.

The dc driver supports the following media types:

autoselect Enable autoselection of the media type and options. The user can manually
override the autoselected mode by adding media options to the /etc/rc.conf
file.

Note: the built-in NWAY autonegotiation on the original PNIC 82c168 chip is
horribly broken and is not supported by the dc driver at this time (see the
BUGS section for details). The original 82c168 appears on very early revisions
of the LinkSys LNE100TX and Matrox FastNIC.

10baseT/UTP Set 10Mbps operation. The mediaopt option can also be used to enable
full-duplex operation. Not specifying full-duplex implies half-duplex mode.

100baseTX Set 100Mbps (Fast Ethernet) operation. The mediaopt option can also be used to
enable full-duplex operation. Not specifying full-duplex implies half-duplex
mode.

The dc driver supports the following media options:

full-duplex Force full duplex operation. The interface will operate in half duplex mode if
this media option is not specified.

Note that the 100baseTX media type may not be available on certain Intel 21143 adapters
which support 10Mbps media attachments only. For more information on configuring this
device, see ifconfig(8).

HARDWARE

     The dc driver provides support for the following chipsets:

     •   DEC/Intel 21143
     •   ADMtek AL981 Comet, AN985 Centaur, ADM9511 Centaur II and ADM9513 Centaur II
     •   ALi/ULi M5261 and M5263
     •   ASIX Electronics AX88140A and AX88141
     •   Conexant LANfinity RS7112 (miniPCI)
     •   Davicom DM9009, DM9100, DM9102 and DM9102A
     •   Lite-On 82c168 and 82c169 PNIC
     •   Lite-On/Macronix 82c115 PNIC II
     •   Macronix 98713, 98713A, 98715, 98715A, 98715AEC-C, 98725, 98727 and 98732
     •   Xircom X3201 (cardbus only)

     The following NICs are known to work with the dc driver at this time:

     •   3Com OfficeConnect 10/100B (ADMtek AN985 Centaur-P)
     •   Abocom FE2500
     •   Accton EN1217 (98715A)
     •   Accton EN2242 MiniPCI
     •   Adico AE310TX (98715A)
     •   Alfa Inc GFC2204 (ASIX AX88140A)
     •   Built in 10Mbps only Ethernet on Compaq Presario 7900 series desktops (21143, non-MII)
     •   Built in Sun DMFE 10/100 Mbps Ethernet on Sun Netra X1 and Sun Fire V100 (DM9102A, MII)
     •   Built in Ethernet on LinkSys EtherFast 10/100 Instant GigaDrive (DM9102, MII)
     •   CNet Pro110B (ASIX AX88140A)
     •   CNet Pro120A (98715A or 98713A) and CNet Pro120B (98715)
     •   Compex RL100-TX (98713 or 98713A)
     •   D-Link DFE-570TX (21143, MII, quad port)
     •   Digital DE500-BA 10/100 (21143, non-MII)
     •   ELECOM Laneed LD-CBL/TXA (ADMtek AN985)
     •   Hawking CB102 CardBus
     •   IBM EtherJet Cardbus Adapter
     •   Intel PRO/100 Mobile Cardbus (versions that use the X3201 chipset)
     •   Jaton XpressNet (Davicom DM9102)
     •   Kingston KNE100TX (21143, MII)
     •   Kingston KNE110TX (PNIC 82c169)
     •   LinkSys LNE100TX (PNIC 82c168, 82c169)
     •   LinkSys LNE100TX v2.0 (PNIC II 82c115)
     •   LinkSys LNE100TX v4.0/4.1 (ADMtek AN985 Centaur-P)
     •   Matrox FastNIC 10/100 (PNIC 82c168, 82c169)
     •   Melco LGY-PCI-TXL
     •   Microsoft MN-120 10/100 CardBus (ADMTek Centaur-C)
     •   Microsoft MN-130 10/100 PCI (ADMTek Centaur-P)
     •   NDC SOHOware SFA110A (98713A)
     •   NDC SOHOware SFA110A Rev B4 (98715AEC-C)
     •   NetGear FA310-TX Rev. D1, D2 or D3 (PNIC 82c169)
     •   Netgear FA511
     •   PlaneX FNW-3602-T (ADMtek AN985)
     •   SMC EZ Card 10/100 1233A-TX (ADMtek AN985)
     •   SVEC PN102-TX (98713)
     •   Xircom Cardbus Realport
     •   Xircom Cardbus Ethernet 10/100
     •   Xircom Cardbus Ethernet II 10/100

NOTES

     On sparc64 the dc driver respects the local-mac-address? system configuration variable for
     the built in Sun DMFE 10/100 Mbps Ethernet interfaces on Sun Netra X1 and Sun Fire V100.
     This system configuration variable can be set in the Open Firmware boot monitor using the
     setenv command or by eeprom(8).  If set to “false” (the default), the dc driver will use the
     system's default MAC address for both of the built in devices.  If set to “true”, the unique
     MAC address of each interface is used rather than the system's default MAC address.

DIAGNOSTICS

dc%d: couldn't map ports/memory A fatal initialization error has occurred.

dc%d: couldn't map interrupt A fatal initialization error has occurred.

dc%d: watchdog timeout A packet was queued for transmission and a transmit command was
issued, but the device failed to acknowledge the transmission before a timeout expired.
This can happen if the device is unable to deliver interrupts for some reason, of if there
is a problem with the network connection (cable or network equipment) that results in a loss
of link.

dc%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.

dc%d: TX underrun -- increasing TX threshold The device generated a transmit underrun error
while attempting to DMA and transmit a packet. This happens if the host is not able to DMA
the packet data into the NIC's FIFO fast enough. The driver will dynamically increase the
transmit start threshold so that more data must be DMAed into the FIFO before the NIC will
start transmitting it onto the wire.

dc%d: TX underrun -- using store and forward mode The device continued to generate transmit
underruns even after all possible transmit start threshold settings had been tried, so the
driver programmed the chip for store and forward mode. In this mode, the NIC will not begin
transmission until the entire packet has been transferred into its FIFO memory.

dc%d: chip is in D3 power state -- setting to D0 This message applies only to adapters
which support power management. Some operating systems place the controller in low power
mode when shutting down, and some PCI BIOSes fail to bring the chip out of this state before
configuring it. The controller loses all of its PCI configuration in the D3 state, so if
the BIOS does not set it back to full power mode in time, it will not be able to configure
it correctly. The driver tries to detect this condition and bring the adapter back to the
D0 (full power) state, but this may not be enough to return the driver to a fully
operational condition. If you see this message at boot time and the driver fails to attach
the device as a network interface, you will have to perform a second warm boot to have the
device properly configured.

Note that this condition only occurs when warm booting from another operating system. If
you power down your system prior to booting FreeBSD, the card should be configured
correctly.

HISTORY

     The dc device driver first appeared in FreeBSD 4.0.

AUTHORS

     The dc driver was written by Bill Paul <wpaul@ee.columbia.edu>.

BUGS

The Macronix application notes claim that in order to put the chips in normal operation, the
driver must write a certain magic number into the CSR16 register. The numbers are
documented in the app notes, but the exact meaning of the bits is not.

The 98713A seems to have a problem with 10Mbps full duplex mode. The transmitter works but
the receiver tends to produce many unexplained errors leading to very poor overall
performance. The 98715A does not exhibit this problem. All other modes on the 98713A seem
to work correctly.

The original 82c168 PNIC chip has built in NWAY support which is used on certain early
LinkSys LNE100TX and Matrox FastNIC cards, however it is horribly broken and difficult to
use reliably. Consequently, autonegotiation is not currently supported for this chipset:
the driver defaults the NIC to 10baseT half duplex, and it is up to the operator to manually
select a different mode if necessary. (Later cards use an external MII transceiver to
implement NWAY autonegotiation and work correctly.)

The dc driver programs 82c168 and 82c169 PNIC chips to use the store and forward setting for
the transmit start threshold by default. This is to work around problems with some NIC/PCI
bus combinations where the PNIC can transmit corrupt frames when operating at 100Mbps,
probably due to PCI DMA burst transfer errors.

The 82c168 and 82c169 PNIC chips also have a receiver bug that sometimes manifests during
periods of heavy receive and transmit activity, where the chip will improperly DMA received
frames to the host. The chips appear to upload several kilobytes of garbage data along with
the received frame data, dirtying several RX buffers instead of just the expected one. The
dc driver detects this condition and will salvage the frame; however, it incurs a serious
performance penalty in the process.

The PNIC chips also sometimes generate a transmit underrun error when the driver attempts to
download the receiver filter setup frame, which can result in the receive filter being
incorrectly programmed. The dc driver will watch for this condition and requeue the setup
frame until it is transferred successfully.

The ADMtek AL981 chip (and possibly the AN985 as well) has been observed to sometimes wedge
on transmit: this appears to happen when the driver queues a sequence of frames which cause
it to wrap from the end of the transmit descriptor ring back to the beginning. The dc
driver attempts to avoid this condition by not queuing any frames past the end of the
transmit ring during a single invocation of the dc_start() routine. This workaround has a
negligible impact on transmit performance.