Provided by: freebsd-manpages_11.1-3_all 
NAME
gre — encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration
file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in
loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated
datagrams are routed to a destination host, where they are decapsulated and further routed
to their final destination. The “tunnel” appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy
subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram
and a GRE header. The GRE header specifies the type of the encapsulated datagram and thus
allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on
Cisco routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key
option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
\ /
\ /
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1,
while router B has external address B and internal address 192.168.2.1, the following
commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
In case when internal and external IP addresses are the same, different routing tables (FIB)
should be used. The default FIB will be applied to IP packets before GRE encapsulation.
After encapsulation GRE interface should set different FIB number to outgoing packet. Then
different FIB will be applied to such encapsulated packets. According to this FIB packet
should be routed to tunnel endpoint.
Host X -- Host A (198.51.100.1) ---tunnel--- Cisco D (203.0.113.1) -- Host E
\ /
\ /
+----- Host B ----- Host C -----+
(198.51.100.254)
On Host A (FreeBSD):
First of multiple FIBs should be configured via loader.conf:
net.fibs=2
net.add_addr_allfibs=0
Then routes to the gateway and remote tunnel endpoint via this gateway should be added to
the second FIB:
route add -net 198.51.100.0 -netmask 255.255.255.0 -fib 1 -iface em0
route add -host 203.0.113.1 -fib 1 198.51.100.254
And GRE tunnel should be configured to change FIB for encapsulated packets:
ifconfig greN create
ifconfig greN inet 198.51.100.1 203.0.113.1
ifconfig greN inet tunnel 198.51.100.1 203.0.113.1 tunnelfib 1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco
routers. This may not be an optimal value, depending on the link between the two tunnel
endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not
run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8)
variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a
different key or without a key will be treated as if they would belong to this interface.
The sequence number field also used only for outgoing packets.